Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix DE door error codes or doors that won't latch with this washer door latch hook. Simple 15-minute DIY repair with video guide. Secures door during cycles.
Changed out door switch and door latch hook. Watched video it was so easy. Appliance Parts Pros save me hundreds of $$$$. This is the 3rd time I used this company I must say they are the best. Read more
Washer won't spin or shows LE error? A faulty motor wire harness disrupts power to the drum motor. DIY fix in 20-60 minutes with basic hand tools.
I replaced the rotor and stator motor assembly. Read more
Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.
The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more
Replaces your washer's door boot gasket that seals the drum opening. Install when you notice leaks, mold buildup, or cracks. Confirm fit with your model.
First I watched the very, very helpful video (twice), then I planned out the job in regards to tools, work area, and access. I have stacked units of washer/dryer due to space restrictions and had to ask my son-in-law to help me lift the dryer of the washer once I had prepared the process by fabricating 2 pieces of 3/4" plywood to turn the dryer and then slide it out far enough were 2 people can lift it and then set it on some cribbing for easy handling. Disconnected the power, turned off the... Read more
Replace your washer's drain hose if cracked, leaking, or damaged. Connects the pump to the standpipe for proper water drainage during wash cycles.
I suspected the tub gears where ready to break so I dismantled my LG WM2032HW front load washer. I found the spyder gear corroded and broken. I also found that the stainless steel drum abraded the front tub cover so bad, it was cracked. My washer is an early model and always had standing water in the door seal after a wash. What I learned is LG stopped making the orginal front tub cover and replaced it with one that had a drain hole at the bottom front edge. I also learned that this new... Read more
Motor harness wiring for washers. Connects motor to control board. Replace if wires are damaged, frayed, connectors broken, or harness is worn out.
My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more
This inlet hose routes water from the fill valve into your washer. Replace if cracked, leaking, or worn to prevent water damage and drips.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
Replacement bolt that secures the spider assembly to the inner wash basket. Needed when hardware is missing, stripped, or corroded during repairs.
Can't buy LG parts in Canada without getting an LG Tech to install. $1000 repair was too steep for me so went on websites and bought from Appliance Parts. Watch the video on Appliance Parts. Note - Joyce from Appliance Parts really helped in identifying the bolts that I needed. Read on and you will see why. Stripped down machine and identified the spider had failed along its three arms. Bearings were still in good condition. Managed to get three bolts off spider but remaining three had same... Read more
Washer won't spin or agitate properly? A worn stator disrupts the motor's magnetic field, preventing drum rotation. Moderate DIY repair restores spin.
Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.
I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more
Factory mounting screw for washer tub assemblies, panels, and brackets. Replaces stripped, corroded, or missing screws to secure components properly.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Complete front panel assembly for washer pull-out drawer. Replaces cracked, broken, or missing drawer fronts. Restores clean appearance and handle support.
Ordered a new Drawer Panel Assembly. Unwrapped it and installed it. Read more
Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.
Replacement Read more
Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.
Replaced Read more
Washer door hinge assembly supports and pivots the lid for smooth opening and closing. Replace when worn or misaligned to restore proper seal. Confirm fit.