Wm3499hva Parts

This is the direct-drive rotor for the dishwasher wash motor. It pairs with the stator to spin the impeller and circulate wash water through the spray arms, helping restore proper spray pressure and quieter operation when the original rotor is worn.

• Couples with the stator to drive the circulation pump impeller
• Moves wash water through the spray arms for consistent cleaning performance
• Common failure signs: little or no spray, poor cleaning, loud humming or grinding from the pump area, or intermittent wash action
• Physical damage or weakened magnets can prevent proper rotation

• Disconnect power and water supply and pull the unit forward for access
• Remove the toe-kick and drain remaining water at the sump
• Remove the pump cover and center fastener, then pull the old rotor straight off
• Seat the new rotor fully, reassemble, and run a test cycle to check operation and leaks

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

The stator assembly is the stationary coil pack for the direct-drive motor in your washer. Working with the rotor, it creates the magnetic field that turns the tub and restores consistent wash and spin performance. What it does:

• Generates the electromagnetic field that drives the rotor and spins the drum
• Failure can cause no spin or agitation/tumble, or a stalled drum
• May trigger LE/motor error codes and a humming or grinding noise from the motor area
• Can produce a burning smell or signs of overheating near the rear of the machine

• 1 stator assembly

• Disconnect power; move the appliance for rear access and turn off water if needed
• Remove the rear panel, rotor bolt, and rotor; handle strong magnets with care
• Unbolt and replace the stator; transfer the hall/position sensor and harness if attached, and secure wiring
• Reinstall the rotor and panel; run a test spin

This noise filter assembly conditions incoming AC power to reduce electromagnetic interference before it reaches the control system. A failed line filter can cause no power, intermittent shutdowns, or breaker trips; replacing restores stable, reliable operation. What it does:

• Filters EMI/RFI on the power line to help protect sensitive control electronics
• Helps prevent interference that can cause no power, flickering display, or random resets
• A failing filter may trip a breaker/GFCI when the unit is plugged in or starts a cycle
• Visual clues can include scorch marks, burnt odor, or a cracked/bulged filter body

• 1 noise filter assembly

• Disconnect power before servicing; verify the outlet is de-energized
• Access is typically near the power cord entry behind a rear/top panel (varies by model)
• Label or photograph wire positions and transfer connections one by one; secure the ground
• Mount firmly and route wires to avoid pinching; reassemble and test for proper operation

• Line filter, EMI filter, RFI filter

This replacement bolt secures the drum spider within the washer tub assembly. Replacing worn or missing hardware helps keep the basket properly mounted to reduce wobble, vibration, and noise during spin.

• Fastens the spider to the inner wash basket
• Maintains proper alignment and balance of the basket during spin
• Use when original bolts are rusted, stripped, loose, or missing
• Symptoms include rattling, thumping, off-balance errors, or visible basket wobble

• Unplug the appliance; shut off water and remove hoses if access requires moving the unit
• Access typically requires panel removal to reach the inner basket and spider
• Replace any damaged bolts and tighten evenly in a crisscross pattern; do not overtighten
• Inspect the spider and basket for corrosion or cracks before reassembly

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This locker hook engages the appliance's latch/lock mechanism to keep the door securely closed during operation. Replacing a worn or bent hook restores reliable latching and helps prevent nuisance door/lock errors and cycle interruptions.

• Interfaces with the door lock/latch to secure the door during use
• Allows the safety interlock to confirm the door is closed
• Common symptoms: door won't latch or stay closed, needing to hold/push door to start, door/lock error messages
• Physical signs of failure: bent hook, worn contact surface, or cracked/broken mounting ears

• Disconnect power; turn off water supply if applicable
• Access the hook location on the door or cabinet/tub (varies by model); remove mounting screws/clips
• Transfer any reusable hardware; align the new hook so it mates cleanly with the latch/lock and tighten fasteners
• Close the door to verify smooth engagement before running a cycle

The Shipping Bolt Assembly is an OEM part for LG washing machines. This assembly is used to secure the washer drum during transportation, preventing it from moving and getting damaged. Shipping bolts are essential for maintaining the integrity of the washing machine when it is being moved or installed.

Causes of a bad or missing shipping bolt assembly include improper handling during moves, wear and tear from multiple uses, or not reinstalling them when relocating the washer. Ensuring that the shipping bolts are in place is crucial for protecting the internal components of the washer during transit.

Symptoms of a missing or damaged shipping bolt assembly include:

• Excessive movement or shaking of the drum during transportation
• Internal components of the washer getting damaged during a move
• Difficulty in securing the drum for transport
• Noise or instability during washer installation

This OEM LG part is also compatible with Sears/Kenmore.

This washer water inlet valve assembly regulates and shuts off household water flow into the machine during fill cycles. Replacing a weak or leaking valve restores proper filling performance and helps prevent slow fill, no-fill, or overfilling issues.

• Opens when energized to allow water into the washer; closes to stop flow
• Directs incoming water to the dispenser/tub as commanded by the control
• Failure symptoms can include no fill, slow fill, continuous filling, or water leaking into the tub between cycles
• May trigger fill-related error or fault notifications when sticking or restricted

• Unplug the washer and shut off the water supply before servicing
• Place a towel or shallow pan to catch residual water; relieve hose pressure
• Note hose and wire connector positions for correct reassembly
• Inspect inlet screens and hose washers; reconnect fittings securely and check for leaks after installation

This replacement door handle restores a secure, comfortable grip for opening and closing the appliance door. Replace a cracked, loose, or missing handle to bring back proper function and a clean, finished look. What it does:

• Provides the handhold used to open and close the door
• Mounts to the door with internal screws or bolts specific to the model
• Restores appearance after wear, cracks, or finish damage
• Typical symptoms: cracked/broken or wobbly/loose handle, missing handle, difficulty gripping

• 1 handle

• Disconnect power to the appliance before servicing; allow surfaces to cool
• Access the handle's mounting screws from the inner side of the door; remove trim or panels as needed
• Transfer any spacers or bushings from the old handle to the new one
• Tighten hardware evenly without overtightening; verify door opens and closes smoothly

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

This lifter assembly is the plastic baffle inside the drum that lifts and tumbles laundry as the drum turns. Replacing a cracked or missing lifter restores smooth tumbling and helps prevent fabric snags and noisy operation. What it does:

• Lifts and turns items to promote effective tumbling during cycles
• Helps distribute loads more evenly and reduce thumping
• Replaces broken, loose, or missing baffles
• Addresses symptoms like rattling, clothing snagging/tearing, or poor item movement in the drum

• 1 lifter assembly

• Disconnect power before servicing
• Work through the drum opening; remove the old lifter by releasing its locking mechanism
• Align the new lifter's tabs with the drum slots, then slide/lock it securely in place
• Verify it is firmly seated and does not wobble before running a test cycle

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This clamp assembly secures a hose, tube, or similar connection inside your appliance, maintaining a tight, reliable hold to prevent leaks and movement. Replacing a worn or damaged clamp restores proper sealing and dependable performance.

• Holds a hose/tube or component firmly in place to help prevent leaks or disconnections
• Reduces movement and vibration that can cause noise or wear
• Restores clamping force when the original is bent, corroded, or stretched
• Common symptoms: drips at a joint, hose slipping off, rattling, or a missing/broken clamp

• Disconnect power; shut off the water supply if the clamp secures a water line
• Place a towel or pan to catch residual water and relieve line pressure if applicable
• Note the original orientation; use suitable hand tools to release and seat the clamp securely
• Inspect the hose/tube and fitting for damage; replace if cracked or deformed and check for leaks after reassembly

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed