Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more
Secures the washer lid to the hinge assembly. Replace if stripped, rusted, or missing. Essential for proper lid alignment and secure closure during use.
I just replaced the glass lid and broken plastic frame with the all metal one. Call 877 477 7278 for appliancepartspros and order the following Whirlpool parts (prices as of November 2016): 1 lid part number WP8572026 (AP6013408) for $119.81 2 hinges WP8563964 (AP6004844) for $6.17 each 4 screws WPW10119828 (AP6015313) for $1.97 each Total $140.03 plus $8.95 shipping, grand total $148.98 Note that it does not say that this lid will fit model 7800, but the lid will fit this model. The... Read more
Secures the control console to the top panel of your dryer. Replace this clip if it's broken, cracked, or missing to keep the console firmly mounted.
Fix a washer that won't advance through cycles or gets stuck between wash and rinse. This cycle switch controls your wash sequence. DIY repair.
Ordered the right part, took the back off the top control panel, and popped it in. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Timer knob for dryer control panels. Replacement needed when original is cracked, broken, or worn from regular use. Installs on control panel front.
Replaced timer Read more
Replaces cracked, worn, or missing washer lid bumpers. Cushions lid closure and reduces vibration. Sold individually. Installation video available.
Replaced both with ease after reviewing video. Parts matched OEM specs perfectly. ***Shipping time was excellent - placed order with standard package delivery at @11pm on a Tuesday evening & received the order in Southeast Texas Thursday morning @11am. Read more
Fix a washer that fills but won't spin or agitate. This motor start capacitor stores electrical energy to help start your washer motor. DIY repair.
I was actually getting an error code for the shifter and speed sensor. I ordered a shifter, which included the speed sensor, and replaced that part but the washer still didn't work. After doing some more research online, someone mentioned that the capacitor may be bad. After talking to my dad, who is an electrician, he said it sounded like my problem could very well be the capacitor. Knowing that we'd been without a washer for almost two weeks at this point, I went ahead and ordered the... Read more
Replaces broken or worn washer lid hinge bearings. Installs in the lid hinge assembly to allow smooth opening and closing. Needed when bearing is cracked or missing.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
If your washer agitator spins freely or won't move clothes, the upper agitator may be worn. Often replaced with agitator dogs. Video guide available.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Fix a washer that won't fill or continuously fills with this water inlet valve. Controls hot and cold water flow into the tub. Simple DIY repair.
Super simple project that cost 110. My stackable washer is back in action. Read more
Cracked bleach dispenser leaking onto your washer? This cup holds and meters bleach during wash cycles. Simple snap-in installation, video included.
Just took the old one out and inserted the new as instructed by your knowledgeable staff. This is my second time using your firm and would recommend you to anyone needing parts and your staff's know-how. Read more
Snaps onto the outer tub to contain splashing and guide water back into the basket. Replace if cracked or loose to stop leaks and prevent imbalance issues.
Replace the all four suspension and ring tub. it work like brand new. thanks for having the parts that i needed. and the fast shipping. michael moore Read more
Fix unresponsive buttons, blank displays, or cycle selection failures. This washer control panel houses input dials and digital displays.
Fix washer shaking and excessive vibration during spin cycles. This leveling leg locking nut secures adjustable legs to stabilize your machine.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
Washer won't spin or agitate? A faulty drive motor causes humming noises and stopping mid-cycle. This direct replacement restores drum rotation.
This was a tricky one to figure out. The Maytag Centennial MVWC400XW4 would fill and wash, then stop before spin cycle or would not complete the spin cycle. We had to manually move the dial to rinse & spin, etc. to get it to finish a load. This technique worked but it definitely became a pain to do and at the time we didn't notice how much longer the machine took calibrating a wash load. I called Sears initially thinking I really didn't want to mess with this and they came out. They... Read more