Solenoid Parts

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

I replaced the Inlet Valve. The part arrived ahead of schedule and was approximately $10 cheaper from AppliancePartsPros.com. This is the second time that I ordered parts from this company and have had great success with each one. Thanks Larry Read more

Ordered water inlet valve, watched repair video and installed it very quickly. Totally solved problem. Defrosted freezer and working great now. Read more

Replaced inlet valve. Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more

• Will not fill with water

The GE front loading HE washer wound paused at the rinse fill point and need manual selection of drain & spin to finish the load. Online searches told me how to get the error code. Once E22 was found online searching told me it was a water flow problem- slow fill. I removed the hoses at the washer and inspected for clogs - nothing was found. I then put the ends of the hoses in a bucket and turned on the water- strong flow. Interesting is some debris/solids came out. I’m betting over time solids... Read more

Replaced broken part with new part. Easy peasy. Read more

• Leaking
• Not dispensing water
• Noisy

Verified that the water line had flowing water, check. Removed lower screen and vacuumed and cleaned all dust. Proceeded to test water flow to the valve and beyond the valve. The valve did not allow water to pass through it. Nor would it open or close. Went to Marbeck for confirmation and was sent to your website for the part. Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more

Perfect Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more