Line Hook Line Mover Float Needle Parts

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

Needed to replace diverter valve. Since you can't get service now due to covid restrictions. We needed to order direct. The service was exceptionally great. Received tracking number right away. Since I ordered overnight delivery, the part came early next day and we are up and running! Read more

Replaced the door latch/lock assembly. Read more

Replaced door lock switch. Read more

Ordered parts from Appliance Parts Pros and replaced them.Works like new Read more

I figured it was the valve, but searching on the Appliance Parts site, somebody said they fixed it by replacing the switch flood assembly. So I order both parts. The Switch Flood Assembly was easiest to replace, so I decided to try that first. When I pulled out the old assembly, I noticed it did not 'rattle', as the new one did. So, there is apparently a float ball that had gotten stuck. I put the new one in and poof.. it worked. The only update to the instructions is a reminder that the... Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

It finally gave E15 code, then after drying out the E15 code came back within 5 minutes of running. I dried out the base then I ran the dishwasher and observed water coming down the overflow chute after running only 5 minutes.There is a water inlet (clear water chamber on the side of the machine). It had some gunk inside that was stopping a black float shut-off from moving. I replaced the water inlet chamber. I also suspected the non return valve (also called a check valve). From the parts... Read more

• Will not fill with water
• Noisy

Recently my Kenmore dishwasher would start but would not fill with water. A quick test of the float switch reflected proper operation, AND voltage was being delivered TO the contact on the water inlet valve. I then removed power and checked for continuity on the contacts. This read “infinity” (Open circuit) which indicated a break in the coil inside the valve’s solenoid. As such the valve would not open to allow water to flow. I ordered the replacement water inlet valve from... Read more

• overflowing
• Noisy

Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more

Replaced the lock lid mechanism. Read more

• Door won't close
• Won't start

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Replaced it. Read more

About a year ago my dishwasher during a cycle was emitting a horrible plastic burning smell. We stopped it mid-cycle, cleaned it out and tried to run a few more cycles after that and realized it wouldn't drain so it sat in my kitchen broken for a year. I finally got so fed up with washing dishes by hand that I took the whole dishwasher apart. Confirmed there were no blockages in any of the hoses etc. when it still didn't work I googled the problem, found this website and found that it must be... Read more

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more