Turn Line Mover Float Needle Parts

Only two screws hold the mount of the pump in the lower left near the floor. Easy access by removing the front covers then remove the two mounting screws to the pump assy. Then remove the intake and output hoses. I noticed on the new pump a male hose bib on the intake. Supplied with the dishwasher was the smooth intake water tube. Best to not reuse this supplied hose. It just won't clamp tight enough for a good seal. Cut a portion from a garden hose the same size as the intake valve bib... Read more

• Will not drain

So all of a sudden the dishwasher stops working, "0E error"on the panel. Did some google searches and found that it might be the filter, which I did not know needed to be changed, or worse, the motor. Took the filter off per online tutorial (easy) and mopped up all the stagnant water. Poking around, I find the small rubber check valve that has broken. Had to fish it out with tweezers. Long story short, it was not the motor and I doubt it was the filter. It was this $1.87 rubber drainage... Read more

I bought a new controller first and installed it. The exact replacement controller was no longer available and I had to modify two AC connectors that changed from 3 pins with two wires to two pins with two wires. This was not expected but I made it work just fine by getting the three pin connectors on the cable to fit the two pin by breaking out the center web in the board two pin and then shaving off the raised key plastic on the wires. Then on power up, I found that the wash motor did not... Read more

Purchased your parts watched the awesome video on your site. Repair was complete within an hour the dishwasher is running as I am typing this. Thank you so much for the service you offer. Regards, Rich Read more

• Will not fill with water

Took the washer out, turned it over and found the solenoid that worked the drain valve to be melted, and the shaft that the solenoid activates was heavily corroded. I found the right parts on your website after reading the notes left by other customers, then watched the video. The repairs were fairly simple and successful. This was a GE profile dishwasher. Read more

Here's what the problem was: Started the 'Normal' cycle... I closed the door... it calls for water, water fills, ECS sensor doesn't kick it to the next segment of the cycle (wash), so the water over-fills and reaches the over-fill sensor. So many other are replacing the plastic 'case-brake,' main board, and the ECS sensor. I, however, was able to get by with just the ECS sensor replacement, which is known to be a faulty design by Samsung, supposedly. The idea is replace the (1) most common... Read more

First determined drain discharge hose was clear. Turned of power to dishwasher. I did not find it necessary to remove the dishwasher. I simply removed the lower service panel at the floor and was able to easily remove the defective pump, unplug it, replace the small rubber check valve flapper before the pump inlet and reinstall the new pump assembly. The dishwasher surprisingly cleans and runs quietly like new again although I found no excuse for the pump failure as it is well designed. Never... Read more

Replacing the heating element and float switch with AppliancePartsPros.com hardware and Repair Clinic YouTube videos. Just followed the videos and made the swaps. Was able to complete and test all repairs in a single evening. Read more

• overflowing

Replaced the water inlet valve and float switch. Read more

I first installed the inlet pump with no results. I then ordered a Control Switch and Float and Nut. This fixed the problem. Everything comes out so clean. I also replaced the filter which allowed me to clean debris around old filter. It is also easier to replace all these parts with the dishwasher pulled out and tilted on its side. I had to pull mine out to unplug power to the dishwasher. Read more

I drained the dishwasher by hand, disconnected power, water, and drain under the sink. I removed the screws holding the dishwasher in place. I located the pump with the online owners manual and removed it leaving the power connected. I put the machine on the rinse cycle and then hit cancel, the pump is supposed to come on, it didn't, I tried it twice, each time it would start if I manually started it spinning. So I ordered a new drain pump and reversed the removal procedure. Everything worked... Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more