Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Agitator barely moving clothes? Worn agitator dogs prevent the ratcheting action needed for proper washing. Simple DIY fix in under 30 minutes.
I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more
Washer making loud grinding noise during spin or agitation? Drive clutch kit repairs worn clutch assembly. Moderate DIY repair, typically 30-45 minutes.
Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more
Fix a washer that won't spin or agitate with this drive hub kit. Transfers power from motor to basket. Moderate DIY repair with video guide included.
I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more
Washer won't spin or shows F7 E1 error? The shift actuator controls cycle transitions. Moderate DIY repair with video guide available.
After internet search of symptoms, discovered that the hub that connects the drive shaft to the tub was stripped causing intermittent spinning which in turn caused the knocking and creating the unbalanced condition. Appliance Parts Pros got me the hub within a day and the other part a little longer due to snowstorm, but still timely. To replace the hub: Remove agitator by popping off plastic cap, undoing the bolt, take agitator of the shaft by tugging at it from side to side, if it seems like... Read more
The washer drive belt transfers motor power to the washer’s drive system so the basket spins and agitates. Replacing a stretched or broken belt helps stop squealing and slipping so cycles finish at proper spin speed.
What it does
What’s included One drive belt.
Install notes
This OEM Whirlpool belt is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more
Suspension rod supports and stabilizes the washer tub assembly. Replace if cracked, worn, or damaged to restore proper tub support and balance.
Replaced suspension springs/rods and all associated bushings in the kit. Read more
Washer won't start or stops mid-cycle? A faulty lid lock assembly prevents operation. Moderately difficult DIY repair—installation video available.
The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more
Upper agitator not spinning or turning freely? This short cam agitator repair kit includes dogs, cam, and retainer. DIY-friendly 10-minute repair.
I searched the internet for the most likely cause of the problem and then went to the AppliancePartsPros.com site to see if they had the parts. Naturally they did, but the best part was that they had a video on how to change the part. The video was very clear and straightforward. So easy to follow. I ordered the part mid-day on a Thursday. Imagine my surprise when later that day an email came in letting me know that the part was already shipped! The next day the part was on my front... Read more
Fix grinding gears or a loose, rattling agitator. This complete assembly restores washing action. Easy 5-minute DIY repair with video guide.
Installed new agitator Read more
Fix a washer that won't fill or fills slowly with a new water inlet valve. Controls hot and cold water flow into the tub. Moderate DIY repair.
Replaced solenoid valve assembly. Easy repair. Read more
Washer won't spin or agitate? A worn drive block often causes spinning failure. This connects the transmission to the tub. Moderately difficult repair.
Fix an agitator that won't turn or leaks fabric softener with this inner cap. Simple 5-minute repair—remove the outer cap and replace. Video guide included.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Rubber washer that seals beneath the agitator bolt to secure the agitator to the drive shaft. Replace if agitator loosens or leaks occur. Verify fit.
I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more
Washer won't spin or stops mid-cycle? A faulty lid lock strike prevents the lid from securing properly. Moderate DIY repair with included video guide.
Loud grinding noise during spin cycle? Failed gearcase bearings cause noise and oil leaks. Moderately difficult repair requires disassembly and cleanup.
Disassembled washer and replaced gearcase and reassembled. Read more
Secures the washplate to the drive shaft in your washer. Replace if stripped, damaged, or missing during washplate repairs or agitator service.