Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.
My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more
Transfers motor power to rotate the drum. Replace if dryer hums but won't spin or makes squealing sounds. Verify fit with your model number.
Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more
Traps lint and debris during drying to prevent clogs and maintain efficiency. Replace if cracked, warped, or damaged. Verify fit by model number.
Had to purchase a new filter as the felt does not feed back into the ridge in the filter. It seems to me that the felt should not pull out so easily. My dryer isn't even a year old so I think this is a design failure. But the new filter works great and hopefully we won't have this problem again. Thank you for your prompt service! Read more
Dryer won't start or shuts off mid-cycle? This thermal fuse cuts power when overheating occurs. Common fix for E63, E66 errors. DIY repair under 1 hour.
Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more
Dryer not drying or taking too long? A worn blower wheel reduces airflow, causing poor drying performance. Moderate DIY repair in 30-45 minutes.
High temperature adhesive for dryers. Use to bond drum seals, felt guides, and gaskets during repairs. Replace when reattaching worn parts. Confirm fit.
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more
Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.
I ordered a new motor. Read more
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more
If your dryer shuts off early or runs too long, the moisture sensor may be broken. This 5-minute repair helps restore automatic cycle detection.
Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes. Read more
Dryer won't heat or overheats? This thermostat regulates temperature to prevent error codes E66 and E68. Moderate difficulty, 2-hour repair.
Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Dryer not heating? A failed igniter is the most common cause. This part ignites the gas burner for heat. Watch the video for step-by-step replacement.
I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more
Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.
Dryer won't start or stops mid-cycle? This door switch signals when the door is closed, restoring reliable starts. Moderate DIY repair with video guide.
Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.
I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more