Parts for Maytag MDG18PDAGW0: 02 - Cabinet Parts

Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.

Replacement mounting nut for dryers and laundry centers. Secures internal components during operation. Order a new nut if original is missing or stripped.

Secures the front panel to the dryer cabinet. Replace if broken or missing to ensure proper panel alignment. Verify fit with your model number.

This screw secures internal dryer components and panels. Replaces lost, stripped, or damaged screws during repairs or maintenance of your dryer unit.

Replace your dryer door seal to prevent heat loss and improve drying efficiency. Install when you notice air leaks or torn rubber around the door opening.

Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.

Cabinet housing for dryers. This outer shell encases internal components. Replace if cracked, rusted, dented, or structurally damaged from impact or wear.

Adjustable leveling foot that screws into the bottom of your dryer cabinet. Replace missing, broken, or cracked feet to stabilize and level your unit.

If your dryer motor has come loose or makes grinding noises, this motor clamp secures the drive motor. Simple DIY repair with basic tools in under an hour.

Idler arm spring maintains tension in your dryer's belt system. Replace if spring is stretched, broken, or unable to keep proper tension on the drum belt.

Secures the idler pulley to maintain proper drum belt tension in your dryer. Replace if worn, loose, or causing squealing noises. Confirm fit with your model.

Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.

Maintains proper drive belt tension to prevent squealing, slipping, and premature wear. Replace if your dryer is noisy or the drum won't turn smoothly.

Mounting screw for securing panels, brackets, or components inside your appliance. Replace if screw is stripped, missing, or damaged during repairs.

Covers and seals your dryer's exhaust opening to direct airflow and keep debris out. Replace if cracked, warped, or missing to maintain proper venting.

Replacement mounting screw for dishwashers. Secures interior panels and components. Replace if stripped, missing, or damaged during service or repairs.

Secures the lower access panel to your dryer base. Replace this clip if broken, rusted, or missing to keep the front toe kick panel properly aligned.

Door hinge pin assembly creates the pivot point for smooth opening and closing. Replace if your dryer door sags, binds, or won't stay aligned. Verify fit.

Replacement screw for dryers and laundry centers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Rubber boot that slips over dryer leveling legs to protect floors from scratches and reduce vibration. Replace when cracked, worn, or missing.

6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.

Rubber bumper that cushions and supports the dryer drum. Replace if cracked, worn, or missing to prevent drum damage and reduce noise during operation.

This motor drive pulley transfers motor torque to the dryer drum belt so the drum spins smoothly and reliably. Replaces a worn or damaged pulley to restore proper belt alignment and reduce noise or slipping. What it does:

• Guides the dryer drum belt so the belt tracks correctly and transmits motor power to the drum.
• Maintains belt alignment and tension to prevent slipping or uneven drum rotation.
• Reduces bearing or shaft wear that can cause squealing, grinding, or vibration.
• Helps restore normal drum rotation when a cracked or worn pulley prevents the drum from turning.

• One motor drive pulley (quantity: 1)

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Inspect belt, idler, and motor shaft for wear; replace damaged components as needed.
• Use basic hand tools; support the drum or bulkhead as required to access the pulley safely.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Dryer drum belt transfers power from motor to drum for smooth tumbling. Replace if dryer won't start, drum doesn't turn, or you hear squealing.

Fix a misaligned or sagging dryer door with this door hinge clip. Secures the hinge assembly to keep your door properly aligned and functioning smoothly.

This flat washer is a small metal hardware piece that spaces and secures fasteners to help prevent loosening and protect mating surfaces. It's used where a smooth, even bearing surface is needed under a nut or screw. What it does

• Provides a stable bearing surface to distribute load from a fastener
• Helps prevent fasteners from digging into or damaging parts
• Reduces loosening from vibration when used with the correct nut or bolt
• Commonly replaced when fasteners become loose, hardware is corroded, or assemblies rattle

• Disconnect power and water to the appliance before servicing electrical or water-connected components
• Remove the fastener, replace the washer, and reassemble using the original fastener
• Inspect mating surfaces and replace any corroded or damaged hardware
• Tighten fasteners securely but avoid over-tightening which can deform the washer

Fix a dryer that won't heat or has burning smell at the power connection. This terminal wire kit replaces burned wires and connectors. Easy DIY repair.

Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.

Replace your worn or damaged dryer drum support pad. This cushioning pad installs between the drum and cabinet to reduce noise and prevent wear.

Dryer not drying properly or leaking? This elbow pipe redirects air or water lines around tight spaces. Restores proper flow and stops leaks. Easy install.

Dryer belt slipping off motor pulley or making squealing noises? The belt restrainer keeps the drive belt aligned. Moderate DIY repair with video guide.

Dryer won't start or turn on? This power cord switch often fails, preventing your dryer from operating. Direct plug-in replacement takes 15-30 minutes.

Dryer won't start when door closes? The door switch detects if the door is latched. Easy 10-minute DIY repair with our step-by-step video guide.

Replaces damaged lower front panel on your dryer. Restores cabinet seal and professional appearance. Confirm fit with your model number before ordering.

Prevents water and air leaks at the dryer front panel. Replace if worn, cracked, or causing moisture issues. Verify fit with your model number.

Flat head screw secures panels, brackets, or trim for a flush fit on your dishwasher. Replace worn or missing screws to prevent rattling and shifting.

Secures the dryer's lower access panel in place. Replace this spring retainer clip if it's bent, broken, or missing to properly hold the panel closed.

Rear door panel for dryers. Installs on the back of the dryer door assembly. Replace if cracked, damaged, or missing to restore proper door appearance.

Replace your cracked, broken, or damaged dryer door assembly. Installs on the front of your dryer to provide access to the drum. Easy installation.

White plastic door handle for dryer models. Mounts on the dryer door exterior. Replace if cracked, broken, or missing to restore door operation.

Replace your dryer's control panel if the original is cracked, broken, or damaged. Covers the control area and restores the finished appearance.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Dryer door won't close or stay latched? This door latch kit restores secure closure. Easy 15-minute DIY repair with common tools. Video guide included.

Secures the handle end cap to the center of your refrigerator door. Replace if missing, stripped, or lost during handle repairs. 8-18 x 1/2 inch size.

Vinyl door seal creates an airtight barrier to maintain proper temperature and prevent energy loss. Replace when worn, cracked, or causing drafts.

Secures the top panel on washer dryer combos. If your top won't stay closed or lifts during use, this lock restores a stable fit. DIY-friendly repair.

Cage nut clips into panel openings to create a threaded anchor point for secure mounting. Replace if broken, stripped, or missing to restore hardware.

If your dryer won't heat, this gas burner coil and valve assembly restores ignition and flame control. Direct-fit replacement for even, consistent drying heat.

Replacement mounting screw for securing panels, brackets, and interior assemblies. Needed when original screw is stripped, missing, or damaged.

Dryer not heating or won't dry clothes? This igniter kit lights the gas burner. Moderately easy DIY repair with video guide—replaces failed igniters.

Fix a dryer that won't heat with this gas valve. Controls gas flow to the burner assembly. Moderate DIY repair typically takes 30-45 minutes.

Poly-V blower belt connects motor to blower wheel for proper airflow. Replace when worn or broken to restore drying performance. Confirm fit with model.

Plug insert for dryer drum or console panel. Replaces cracked, broken, or missing inserts. Covers openings to maintain clean appearance.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.

Washer won't start or displays lid lock error? This lid lock assembly secures the door during operation. Common DIY fix with basic tools needed.

Adjustable leveling foot that screws into the bottom of your dryer cabinet. Replace missing, broken, or cracked feet to stabilize and level your unit.