Chipper Shredder Carburetor

This is a genuine replacement diaphragm kit for select Briggs & Stratton engines. With regular use, the diaphragms and gaskets can wear down and degrade, causing them to fail. If the carburetor cannot mix the gas and air properly because of missing or broken components in the diaphragm, this kit can provide the replacement pieces that are needed for compatible engines. Without a functional carburetor, the engine will fail to run properly or may not run at all, which is why a replacement is essential. This OEM replacement kit fits select engines that feature 2-5 HP and a horizontal crankshaft, found on various models of lawn equipment. It is compatible with tillers, chippers, and other lawn machines, and is fully-compliant with all EPA guidelines. Whenever working on the carburetor, it is essential to disconnect power to the engine and drain the gas. Only perform repairs on a fully-cooled engine for safety. This replacement kit is sold as an individual unit and includes three pieces.

This is a replacement fuel solenoid for Briggs & Stratton engines on some Toro lawn mower models. The fuel solenoid, also called a fuel shut-off solenoid, is responsible for stopping the flow of fuel through the line to the engine after it has been turned off. This prevents unspent fuel from collecting and causing backfiring when the mower is restarted. The fuel solenoid is an electromechanical component that is subject to wear and tear over time and through normal use. Eventually, the mechanical actuator will wear out, and the solenoid will need to be replaced. The solenoid can also suffer from electrical failure. Physical damage to the solenoid is unlikely, though. To replace the solenoid, make sure the engine is off. Locate the solenoid on the engine, and use pliers to crimp the fuel line and prevent spilling. Unscrew the old solenoid and remove the wiring harness. Install the new solenoid, reconnect the wiring harness, and uncrimp the fuel line. This is a genuine OEM replacement solenoid and is sold individually. It is compatible with over 150 different Toro lawn mowers and lawn tractors.

Here is a replacement welch plug for use with the carburetor on small engines and various pieces of outdoor lawn equipment. It is important for a carburetor to have a tight seal, which will prevent an influx of air and cause issues with the fuel mixture. The welch plug is meant to prevent these issues. Over time, the plug could have lost its seal, it could have become corroded, or cracked, or it could have become lost. This could cause a loss of power or for the engine to run rough. Owners must replace the welch plug as soon as possible to avoid issues with their engine. This welch plug is a genuine OEM replacement part that is sold separately. The plug can be used on many different types of small engines and lawn equipment, such as lawn mowers, snowblowers, lawn tractors, and chippers. Compatible brands include Craftsman, Toro, MTD, Lawn-Boy, Cub Cadet, and Tecumseh.

Carburetors must have tight seals to prevent too much air from getting into the carburetor at one time. If there are issues with a welch plug, it could cause an engine to lose power or to run rough. The plug might have lost its seal, it could have cracked, or it could have become lost. Sometimes, the vibration of the engine is enough to cause a plug to fall out if it is not tightly sealed. A loose fit will cause problems with the flow of fuel. This genuine OEM welch plug is sold individually and can help to seal your carburetor so your engine retains power. The part can be used with a range of lawn tractors, lawnmowers, snowblowers, and small engines. Compatible brands include Tecumseh, Lawn-Boy, Toro, Craftsman, and MTD.

This is a genuine replacement carburetor float designed to work with a range of small engines on lawn mowers, snow throwers, lawn tractors, and other equipment. The carburetor's job is to blend air and fuel to ensure that the engine can operate. A carburetor float helps control the flow of fuel, ensuring the proper level of fuel in the chamber. Carburetor floats are not subject to wear and tear type damage, but they are exposed to caustic gasoline and oxygen, as well as high heat. Over time, they degrade and will need to be replaced. If the engine continually floods and will not remain running, it could be that the carburetor float needs to be replaced. Replacing the carb float will require removing the airbox and cover, the air filter base, the fuel line, and the fuel linkage. Clean the carburetor and then remove the bowl. Remove the damaged float and replace it with a new one. Note that it's recommended to replace the carburetor gaskets at this time, too. This is an OEM replacement carburetor float, and it is sold individually. It works with Tecumseh, Toro, Lawn-Boy, Cub Cadet, MTD, and other brands.

This is a carburetor. A carburetor mixes fuel and air before delivering it to the engine. The diaphragm helps regulate the amount of fuel that is in this mixture. The gaskets create a seal that keeps unnecessary air out so that the engine works properly.A new carburetor may be needed if the engine is running roughly when it's at idle, if there are engine misfires, or if the equipment hesitates under acceleration. If the engine won't start, if it cuts off while running, if there is excessive smoke during use, or if the equipment revs on its own, the carburetor may need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine Tecumseh part and is an OEM part sourced directly from the manufacturer and it is sold individually. This carburetor is compatible with engines, chippers, shredders, lawnmowers, and vacuums manufactured by Tecumseh and Craftsman.

This is a main nozzle tube replacement for use with a range of different types of outdoor equipment and small engines. Another name for the main nozzle tube is the fuel jet. The fuel will turn into a vapor and then travel through the main nozzle in a vacuum process. This draws the air into the Venturi pipe. The main nozzle tube is made from plastic, and it can eventually start to break down and wear away. When this happens, it will no longer be efficient. Owners might find that the engine is not running smoothly, or that it is difficult to start the engine. Replacing this element of the system could be what is needed. This is a genuine OEM main nozzle tube replacement. It is sold individually and works for various models of lawn mower, snowblower, tiller, pressure washer, generator, log splitter, wood chipper, and other small engines. Compatible brands include MTD, Toro, Cub Cadet, Lawn-Boy, Craftsman, and Briggs & Stratton. Owners should always ensure they are getting the correct replacement for their make and model.