Parts for Craftsman 358791370: Cylinder / Crankshaft / Crankcase Parts

Combustion engines are quite loud by nature, and their sound and emissions are toned down through the use of a muffler system. In small engines, the muffler often attaches directly to the cylinder to capture the gases and reduce noise. Should that connection weaken or loosen, a replacement bolt may need to be installed to ensure a tight seal and optimal engine performance. This replacement muffler bolt is meant to be installed on edgers, blowers, trimmers and pruners from brands like Poulan, Jonesred, Weed Eater and Husqvarna. This is an OEM replacement part and is going to be responsible for fastening the machine's muffler to the cylinder. It will require the proper hex key to install properly and is considered an easy repair frequently required on many small machines.

This genuine muffler is designed to offer a replacement for select lawn and garden equipment engines. The muffler is part of the exhaust system and it is responsible for reducing the noise from the engine as it exhausts out of the unit. Over time, mufflers are known to get clogged, rust, or otherwise wear out and require replacement. If the muffler becomes clogged or damaged, it will need to be replaced in order to operate the equipment safely. This is a genuine OEM replacement muffler that is manufactured to specific standards. It is made by Weed Eater and is compatible with several of their machines, as well as units from Husqvarna and Poulan. The muffler is sold as an individual unit and does not include the hardware required for installation. It is used in select trimmers, pole pruners, edgers, and lawnmowers. To replace the muffler, it will be important to wear gloves and allow the engine to cool completely. Remove the old muffler and replace it with the new unit, securing it into place with the existing hardware. In the event that the hardware also needs to be replaced, it can be purchased separately.

This is a genuine engine cylinder that is designed for use in select outdoor power equipment. The cylinder is the part of the engine that houses the spark plug and piston, creating the combustion chamber that the engine needs to ignite the air-fuel mixture that runs the engine. The cylinder is exposed to high heat, excessive pressure, and chemicals that can all cause wear and breakage over time. In the event that the cylinder goes bad, it needs to be replaced immediately to prevent further engine damage. This OEM cylinder is manufactured by Husqvarna. It can be used in trimmers, blowers, edgers, and pruners from the brand, as well as from Poulan and Weed Eater. The cylinder is sold as an individual unit and does not include hardware or other parts or accessories. Replacing the cylinder takes a little more effort because it requires disassembling the engine. To replace the cylinder, remove the engine shrouds, and then remove the engine from its mount. From here, the cylinder can be removed from the block and the piston can be taken out. Then, the new cylinder can have the piston installed before being bolted into place. The accessories can be replaced and then the engine can be re-mounted.

This gasket replacement kit is for use with several types of handheld lawn and garden tools to help ensure there are no leaks of air or oil in the engine. They are an important part of the engine and help it continue to run efficiently. Over time, the gaskets will start to wear down. They might become brittle and start to crack. In some cases, they may no longer sit properly and could allow for leaks. If an owner notices an engine running roughly or leaking oil, the problem could be with the gaskets. They will need to be replaced. This replacement gasket kit is a genuine OEM selection. It includes the major gaskets and O-rings that need to be replaced when the owner is rebuilding an engine. These gaskets will work with trimmers and pole pruners. The compatible brands include Craftsman, Weed Eater, Poulan, Poulan Pro, and Husqvarna. Buyers should always double-check to ensure the gasket kit is compatible with their make and model.

A piston ring is a component located between a piston and a cylinder and helps the engine operate correctly. This component maintains gas compression between the cylinder wall and piston, makes lubricating oil to prevent scuffing, transfers heat from the crown of the piston to the cylinder, and prevents the piston from hitting the cylinder wall. There are several signs that a piston ring needs to be replaced. Excessive smoke may come out of the engine, oil may be used more rapidly, and your equipment might have a decreased performance without the power it used to have. If the engine is still in good shape, but the rings have lost their tension, replacing the piston ring is the best solution. Inspecting the cylinder for wear is also important since damaged piston rings can lead to cylinder wear. This piston ring is a genuine OEM product directly from the manufacturer. It comes as an individual part. It can be used on hedge trimmer, leaf blowers, and trimmers from Husqvarna, Weed Eater, and Poulan. Several tools, including a screwdriver and wrenches, might be required to install the replacement part.

Here is a replacement piston kit for use with handheld lawn and garden equipment engines. The pistons in an engine are essential to transfer combustion power to the various working parts of the machine. Pistons might need to be replaced if they have suffered any sort of damage or corrosion. There are several parts to the system including the piston, rings, wristpin, and circlips. The damage or wear and tear could occur in any of these different parts. When replacing a piston, it is a good idea to replace all of the parts of the kit, not just the part that is having issues. This authentic OEM piston kit is compatible with string trimmers, leaf blowers, hedge trimmers, pole pruners, and edgers. It is sold individually and is compatible with Husqvarna, Craftsman, Poulan, Poulan Pro, and Weed Eater brands. Owners buying a piston kit need to be sure they are getting the right part for their make and model.

This carburetor adapter attaches to the gasket on some kinds of lawn equipment with small engines. It is made of a durable plastic material, but wear and tear or impact can cause the part to become damaged. If the part is damaged or broken, the carburetor adapter will need to be replaced with a new component.A visual inspection can determine whether the carburetor adapter should be replaced. The fuel lines and throttle linkage will first need to be removed. Next, the bolts on the carburetor should be taken out so the carburetor can be removed. Take the bolts out of the carburetor plate and remove it. This will give access to the carburetor adapter so it can be determined whether it needs to be replaced. Simply install the new part before reassembling the machine so it can be used again.This replacement carburetor adapter is designed for use with string trimmers and pole pruners manufactured by Craftsman, Poulan, Poulan Pro, and Weed Eater. It is a genuine OEM part that is directly sourced from the manufacturer. This part is sold as an individual component.

This replacement screw is intended for use on a variety of lawn and garden tools to attach components. It is a genuine OEM part sourced directly from the manufacturer. It is used to attached the trimmer head to the shaft in weed eaters and in many other applications on other tools. Overuse and normal wear and tear can cause damage to the screw. The screw can also become stripped when it is over-tightened or bent from contact with heavy debris. The screw will need to be replaced if this happens. Routinely inspecting equipment will help reveal broken or missing screws that need to be replaced or tightened. This screw is a star-slotted screw that requires a Torx screwdriver to remove it from the machinery. If the screw is in a tight-fitting area, an extension socket with a Torx bit can be used to remove the screw and to install a new one. When replacing a screw, check the remaining screws for damage and tighten any that are loose. This screw is a silver-colored, heavy-duty metal screw sold individually. It is compatible with trimmers, leaf blowers, leaf vacuums, hedge trimmers, and other equipment manufactured by Craftsman, Weed Eater, Poulan, and Husqvarna.

This carburetor is an original OEM part sourced directly from the manufacturer, Husqvarna. It is sold individually. A carburetor is designed for use with pieces of outdoor lawn and garden power equipment with small engines such as trimmers and string trimmers. It is compatible with products by brands such as Craftsman, Weed Eater, and Poulan.Having an OEM carburetor is crucial if the time comes to rebuild or replace the machine's carburetor. The purpose of the carburetor is to mix air and fuel in the proper air-to-fuel ratio for internal combustion engines. The replacement or repair process is necessary when the carburetor fails to perform as expected. Any number of symptoms could indicate a faulty carburetor, ranging from poor engine performance to black smoke from the exhaust. Other indicators of a bad carburetor include backfiring, overheating, and hard-starting. When using the carburetor kit to repair or replace the machine's carburetor, be sure to complete the work in a well-ventilated area. It is essential that anyone involved in the rebuild knows to drain any leftover fuel from the tank and fuel lines prior to beginning the rebuild process. It's also important that the repair person or repair team wears proper safety equipment throughout the installation process, such as work gloves to protect the hands.

Screws are responsible for holding together various lawn and garden engine components and housing parts. Although it is made of durable metal, the screw can be subject to damage from an incident or impact. It could also become worn or stripped over time, or even lost in the process of other repairs. As a result, a replacement would be necessary, and it should be made as soon as possible. This screw will provide the perfect fit for compatible machines. This genuine OEM replacement screw is manufactured by Husqvarna to exact standards. It can be found in applications on more than 150 machines from Poulan, Husqvarna, Weed Eater, and Jonsered. The screw is used on multiple machines, including hedge trimmers, pruners, blowers, and trimmers. Be sure to check the parts diagram for exact application and location of this screw. The screw is sold individually as a single unit and those who need more than one will have to purchase additional quantities. This screw is made of premium metal and requires a Phillips head screwdriver for replacement.

This OEM replacement part is a foam air filter for a weed eater. This part sifts out dirt and debris before it can enter the carburetor and engine. The carburetor is responsible for maintaining the delicate balance of air and gasoline needed to create a spark in the engine. If it becomes clogged by dirt that's been kicked up into the air during mowing, the mixture will become contaminated and the carburetor will no long work properly. Foam air filters should be replaced every three to four months, depending on how much use the weed eater gets. Generally, after 25 hours of use, the filter will become clogged and will no longer function efficiently. When changing out the filter, first apply a small dab of two cycle oil to the pouch that the filter arrives in. Squeeze with a bit of paper to remove any excess oil and then switch the old filter for the new. This will help the filter collect dirt and debris. This filter is made of seafoam green foam and is intended to be used with Poulan, Husqvarna, and Paramount weed eaters. It ships individually and is sourced from the original manufacturer.

This part is a replacement air filter cover. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace broken or defective air filter cover in a variety of line trimmer models. The air filter cover keeps the air filter protected from dirt, debris, the elements, and anything else that may damage the filter. This part should be replaced with a genuine OEM replacement part if cracked, detached, or otherwise rendered ineffective. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this air filter cover, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this air filter cover is suitable for use on several different models of line trimmers manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable plastic and is sold individually.

These ignition screws are used in the ignition systems on a variety of lawn and garden equipment. The screws are made of durable metal and fasten together different parts in the ignition system. While the screws are made of high-quality material, they can experience stress, wear and tear, and impacts that will break or damage them.To replace an ignition module screw, the garden tool will need to be disassembled. First, it should be turned off and placed on a flat surface. The spark plug wire should be disconnected before making the replacement. The ignition assembly will need to be taken apart to reach the ignition module screw. Use a screwdriver to remove the old part and replace it with a new replacement screw.This is an authentic OEM replacement component that is sourced directly from the manufacturer. The part is sold as an individual unit. Each ignition module screw is designed to be used with hedge trimmers, string trimmers, leaf blowers, edgers, and pole pruners created by Craftsman, Husqvarna, Poulan, Poulan Pro, and Weed Eater.

Designed for use with a wide range of string trimmers, this momentary switch is a genuine OEM replacement part. A momentary switch, also known as a kill switch, is a safety precaution that kills an appliance's engine in a moment, even if the engine is not set to the off position. This helps prevent accidents if the operator begins to lose control of the trimmer. At the touch of a button, the engine cuts and cannot be restarted for a short period (usually about five seconds). Momentary switches are positioned in a way that they don't often sustain damage but, over time, they can wear out. Once a switch stops working, it will need to be replaced to ensure safe operation. This is a fairly straightforward fix that only requires a screwdriver to open the tiller's handle and pliers to safely remove the wiring. This part is designed for string trimmers made by Poulan, Weed Eater, Paramount, and Husqvarna. It ships individually of any other hardware is comes sourced from the original manufacturer.

This starter rope is a genuine MTD part, sold individually. This starter rope can be used as a replacement part in a string trimmer. The purpose of a starter rope in a string trimmer is to give the operator a component to pull to engage the pull-start mechanism of the appliance, which loops around the pulley and facilitates the powering on of the small engine of the string trimmer.The starter rope in a string trimmer is a crucial component of the pull-start mechanism that might need to be replaced if the starter rope suffers damage from general wear and tear with long-term use or as the result of an accident. If the starter rope is sufficiently frayed, punctured, ripped, scraped, torn, or otherwise damaged to the point that it cannot function, the starter rope should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This starter rope is compatible with the following outdoor appliance brands: MTD, Craftsman, and Weed Eater.

This is a starter pulley that is used with various types of string trimmers from major manufacturers.The pulley keeps the starter rope in the right location so that the chainsaw comes on and offers cutting power. Through wear and tear or impact, the starter pulley can break or become damaged.If a user pulls the starter rope and the engine does not start, the starter pulley may not be working correctly. It will need to be replaced. Before the replacement is made, make sure the tool is turned off and the spark plug wire is disconnected. The starter pulley and rope can be reached by disassembling the trimmer. The recoil spring should be rewound before the rope is threaded back in.This starter pulley is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The component is made for use with string trimmers manufactured by Turf King, Craftsman, Paramount, Weed Eater, Poulan, and Poulan Pro.

The flywheel is a heavy metal wheel that connects to the rotating shaft. Its purpose is to help regulate how power is delivered from the motor to the rest of the tool. Its weight and inertia oppose and moderate small changes in the speed of the engine and holds onto that energy for use when needed. The most common problem with flywheels is for them to crack. As the engine begins to age and other parts begin to break down, excess vibration in the engine can cause the flywheel to wear down, grate, and even shatter. The flywheel needs replacing when the motor begins slipping into the wrong gear. The exact steps for replacing the flywheel will depend on the specific model being repaired. It should only require a screwdriver. This is a genuine OEM replacement flywheel assembly for gardening hand tools like leaf blowers, edgers, weed eaters, and hedge trimmers made by Craftsman, Husqvarna, Weed Eater, Poulan, Poulan Pro, Paramount, Turf King. This part ships individually.

This is a genuine outer bearing replacement for use on select models of outdoor lawn and garden equipment. The outer bearing is installed on the crankshaft and helps create a flexible joint for the various components to move against. This bearing is made of durable metal material, but over time it can become worn and damaged. It may also come loose or get lost in the process of other repairs. In any case, a faulty bearing will need an immediate and original replacement. Wear gloves and allow the engine to cool completely before beginning any repairs. Be sure to take the crankshaft components apart carefully to access the bearing so that they can be reassembled properly. Bearings should also be lubricated when installed.This is an OEM part that is manufactured to exact standards. It is made by Craftsman and can be used in machines from Weed Eater, Poulan, and Craftsman. This bearing can be used in compatible blowers, edgers, trimmers, pruners, and hedge trimmers. It is sold as an individual unit and there is no additional hardware included.

A crankcase seal is what prevents the oil from leaking between the crankcase opening and the crankshaft. It is often found on the engine's front or underside and seals the timing cover to the crankshaft. Oil seals may become damaged or worn with use. Bearing seizures and grinding indicate that the crankcase seal should be replaced. If there is oil leaking from the crankcase or on the crankshaft, a replacement crankcase seal is necessary.Wear gloves and be sure to collect all the tools needed prior to starting a replacement. Replacing a crankcase seal requires Torx wrenches, a container for fuel, spark plug socket or wrench, adjustable or 10-millimeter wrench, rubber mallet, long-nosed pliers, screwdriver, adjustable pliers, socket set, starter rope, 2-cycle engine oil, ignition gapping gauge, and a razor blade. Follow the operator manual for specific directions.The crankcase seal is a genuine OEM part. It is sold individually. The crankcase seal is black, round, and made from durable, high-quality plastic and metal for extensive use. It can be used in a variety of lawn equipment, including leaf blowers, trimmers, hedge trimmers, and vacuums. It is compatible with various manufacturers, including Craftsman, Husqvarna, Weed Eater, RedMax, and Poulan Pro.

This replacement piston kit is designed to be used with many different types of handheld lawn and garden equipment. The pistons are important parts of the engine. The crankshaft powers the pistons, so they move up and down within the cylinder. The purpose of the pistons is to transfer the gas that expands within the cylinder. The pistons can begin to wear out over time, which means that they could fail, which will cause serious problems for engine performance. If there are issues with the piston, a replacement piston kit is essential to get the machine back up and running. When a piston goes bad, it will cause the engine power to decrease. In some cases, the engine might lose all power. Replacement will require pliers, a set of wrenches, and a screwdriver to complete. This high-quality piston kit replacement is a genuine OEM part. It is sold individually. The part can be used for pole pruners, edgers, leaf blowers, string trimmers, and hedge trimmers. Compatible brands include Weed Eater, Poulan, Poulan Pro, Husqvarna, and Craftsman.

This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.

This item is a fuel retainer tank for use on lawn and garden trimmers. It is a genuine Husqvarna part. It is a small item but is very important, as it prevents the fuel inside the tank from becoming contaminated or dirty. Contaminated fuel can ruin a trimmer or other appliance.This retainer is a genuine OEM part sourced directly from the manufacturer and is sold individually. Replacing the retainer is a simple repair that is appropriate for beginners. The retainer usually comes off easily without the use of tools. It is normal for the retainer to experience damage throughout the life of the trimmer and need to be replaced.This retainer is made for compatibility with several brands and models of weed whackers and trimmers, including Craftsman, Husqvarna, Poulan, and Weedeater. It may also be compatible with similar products made by AYP, Jonsered, McCulloch, and RedMax.

The Fuel Pick Up Assembly is an OEM part for Husqvarna outdoor power equipment, including chainsaws, trimmers, and blowers. This assembly is responsible for drawing fuel from the tank to the carburetor, ensuring the engine receives a steady supply of fuel for optimal performance.

Over time, the fuel pick up assembly can become clogged or damaged due to debris in the fuel, exposure to ethanol-blended gasoline, or regular wear and tear. If the fuel pick up assembly is compromised, it can lead to poor engine performance or difficulty starting the equipment.

Symptoms of a bad fuel pick up assembly include:

• Engine not starting or hard to start
• Engine stalling or running inconsistently
• Reduced power or performance
•  Visible damage or clogging in the fuel line

This OEM Husqvarna part ensures proper fuel delivery and compatibility with your outdoor power equipment.