Need Help?
Call or text
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Felt seal that fits around your dishwasher's door vent to contain steam and moisture. Replace if you notice condensation or minor leaks during cycles.
Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix. Read more
Replace your washer's door boot seal when you notice leaks, tears, or mold around the door opening. Creates a watertight barrier. Confirm fit with your model.
Replaced the seal. Read more
Replace worn water inlet valve seals to stop leaks and restore flow. Install when seals are cracked or flattened. Confirm fit with your washer's model number.
Opened the washer (details later) and noted the controls and water path. Ordered dispenser bottom and cover and dispenser valve assembly and rubber washers. When the parts arrived I removed the top portion of the detergent dispenser assembly; removed the door and 2 screws from opposite door wall; snap open the front cover and lifted it off; removed 1 metal screw each from the bottom front corners of the top cover; lifted the top cover and used a piece of wood to hold it up; pull... Read more
Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.
Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.
Replaced blower housing seal Read more
Black door boot seal creates a watertight barrier between the door and tub on front-load washers. Replace when worn or torn to stop leaks. Verify fit.
Creates a watertight seal between the washer door and tub. Replace if you notice leaks, tears, or mold buildup. Confirm fit with your model number.
Creates a watertight seal between the washer tub and cabinet. Replace if you notice water leaking during wash cycles. Verify fit with your model number.
Disassembled washer, found that 2 out of the 3 basket support legs had cracked through. Unfortunately, support cannot be bought except as an assembly, so had to spend almost $300 for the part. Bearings were worn, but not trashed, so I replaced them and the seal. Note, most parts places (including AppliancePartsPros.com) will only sell the bearings and seal as part of the rear tub assembly. The bearings are standard 6205 and 6206 sealed ball bearings, available from Grainger and many others for... Read more
Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Seals the door opening to the outer tub on front-load washers. Replace if you notice leaks, tears, odors, or clothes snagging. Confirm fit with your model.
Followed online instructions. Read more
Flexible rubber seal around the door opening that prevents leaks during wash and spin cycles. Replace if torn, cracked, or moldy. Confirm fit with your washer model number.
Vinyl door seal lines the dryer door perimeter to block air leaks and cushion closure. Replace when worn or cracked to restore a tight seal. Verify fit by model.
Ordered new gasket and adhesive! Read more
Secures your washer's inner door gasket to maintain a watertight seal and prevent leaks. Replace if the gasket is loose or water escapes during cycles. Confirm fit with your model number.
Rubber gasket that seals the joint between the tub and cover to prevent leaks and water seepage. Replace if you notice leaking or debris buildup. Verify fit.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more