Need Help?
Call or text
Roller bearing cage installs in the dishwasher rack track to support smooth gliding. Replace if cracked, broken, or causing the rack to stick or slide out.
I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more
The Mode Shifter & Shaft Assembly is an OEM replacement part for GE washing machines. It is a mechanical component located inside the washer tub that allows for shifting between agitation, spin, and other cycles. The mode shifter and shaft assembly receive input from the control system to precisely change the operational mode at designated points in the cycle. Causes of a bad mode shifter & shaft assembly include worn out or damaged internal gears, stripped or broken shafts, or a loss of integrity in components that restrict smooth shifting between modes. Symptoms of a bad mode shifter & shaft assembly include:
This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
The GE screw is an OEM replacement part responsible for securing various components or parts together on a washing machine. Its main function is to connect and hold together various parts, panels, or brackets, ensuring that they remain securely in place during the appliance's operation. The screw comes in the size 1/4-20 MCH HXW 5/8 S, indicating its thread size, head type, and length.
This part fixes the following symptoms:
The GE washing machine screw can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more
The 2 In 3 Out Water Valve is an OEM replacement part for GE washing machines. It is located within the water supply system to help regulate water flow into the washer tub.
Causes of failure can include obstruction or clogging from mineral deposits over time. Valve components may also wear out with extended usage.
Symptoms of a faulty water valve include:
Compatible models include GE, Hotpoint, RCA, and select Kenmore models.
The GE front loading HE washer wound paused at the rinse fill point and need manual selection of drain & spin to finish the load. Online searches told me how to get the error code. Once E22 was found online searching told me it was a water flow problem- slow fill. I removed the hoses at the washer and inspected for clogs - nothing was found. I then put the ends of the hoses in a bucket and turned on the water- strong flow. Interesting is some debris/solids came out. I’m betting over time solids... Read more
The Micro Switch is an OEM part for GE microwaves. This part ensures the appliance operates only when the door is securely closed. It controls the electrical circuit, allowing the microwave to start heating food when the door latch engages the switch.
Causes of a bad micro switch can include wear and tear from frequent use, electrical issues, or physical damage from slamming the microwave door.
Symptoms of a bad micro switch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
By replacing the switches. Read more
Oven not heating or baking unevenly? The bake element is likely burned out. This 15-minute DIY fix requires just a screwdriver to restore your oven.
Determined the lower heating element wasn't working. Chatted with appliance parts pros and found compatible part. Quick ship and easy replacement. Probable saved over $100 not having a GE service call. Read more
Fix dishwasher leaking from pump housing with this impeller & seal kit. Repairs worn seals causing water leaks. DIY-friendly, typically 30 minutes.
Replaced pump impeller. Read more
Replace your dishwasher's middle spray arm kit if the center arm is cracked, broken, or missing. Includes rotating arm, hub, nut, and washer for middle rack.
I ordered a new arm kit from AP Pro. I watched the video..easy repair. The arm spin jets were plugged just like the video said. The old washer was also worn. The new arm (genuine GE) had redesigned spin jets, they added two more. I ordered on a weekend, the order was filled on Monday and it was at my door at noon on Tuesday! I didn't do any special shipping. Excellent video, shockingly fast delivery. Amazon Prime (I am a member) would be jealous, and AP Pro has excellent videos. Read more
Seals oven door to retain heat and improve efficiency. Replace when hard, cracked, or damaged to prevent heat loss. Clips on in minutes—no tools needed.
Quick and simple fix. Literally about two minutes to remove the old gasket and install the new one. Read more
Replacement timer dial for washers. Installs on the control panel to set wash cycles. Needed when original dial is cracked, broken, or worn smooth.
Easily replaced the knobs Read more
If your burner won't heat or has stopped working, this 8-inch surface heating element restores cooktop function. Easy plug-in installation in minutes.
Ordered new heating coils for stove Read more
Oven not heating or reaching temperature? This bake heating element distributes even heat for proper baking. DIY-friendly repair with basic tools.
Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more
The Defrost Heater Assembly is an OEM replacement part for GE refrigerators. It contains the heating element responsible for maintaining optimal temperatures within the refrigerator. As a crucial component, the heater works to keep stored food safely cooled and prevent freezing.
Causes of a bad defrost heater can include gradual wear over time, mineral buildup reducing heat transfer efficiency, and physical damage.
Symptoms of failure are:
This GE OEM part is also compatible with Hotpoint, RCA, and Kenmore models for simple cross-referencing.
Burner stays on high or won't turn off completely? This infinite control switch regulates surface burner heat. Simple 10-minute DIY fix with video guide.
I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more
The Control Valve Assembly is an OEM replacement part for GE ranges. It plays a key role in regulating gas flow within the oven burners to provide consistent, even heating across various temperature settings. The control valve monitors and controls gas pressure to the oven burners during baking and broiling functions.
Causes of a faulty control valve can include grime or debris deposit buildup on the valve or its components over time, wear and tear on seals from regular oven use, or damage to internal valve parts.
Symptoms of a bad control valve assembly include:
Fixed it by replacing Valve Control Assemble and Range Oven Igniter, a little intimidating at first,but the videos from Appliance Parts Pro made so much easier.Whenever I need parts for appliance in the future AppliancePartsPros will be my first choice. Read more
Broil element burned out or not heating? This upper oven heating element restores broiling function. Simple 15-minute DIY fix with basic tools.
Replaced broiler element with new one. We had difficulties in locating the correct element for my oven. Read more