Generac Parts

This replacement air filter fits the engine on a generator. Air filters serve an important purpose in ensuing that dirt, dust, pollen, and other debris does not reach the combustion chamber, where it could cause damage. Instead, the filter traps and collects these contaminants. However, over time, the air filter will slowly clog with trapped debris, which will restrict airflow to the engine. This causes the engine to work harder than normal, consuming additional fuel, reducing performance, and increasing wear on internal components.Periodically, the owner will need to replace the air filter element. The frequency will vary based on use. Users should check their owner's manuals for specific change interval recommendations. To change the air filter, simply open the air filter housing, remove the old air filter, clean any debris that might have accumulated inside the box, and then install the new air filter. Close the housing when finished.This air filter is a genuine OEM part and is designed for specific Generac generators. It is sold individually.

The Generac air filter element is used to clean the air that enters the carburetor of the generator. This is a two-part filter with a pre-cleaner and a cleaner. The dual filter provides added cleaning before the air gets to the carburetor.Dirt and debris obstructs the flow of air and limits how much air makes it to the carburetor. If the carburetor does not receive proper airflow, this can result in reduced performance and more gas use. Visual inspection, as well as scheduled maintenance, is important in keeping the generator running efficiently. If a visual inspection shows that the filter is clogged, it should be removed and replaced, regardless of the maintenance schedule. Remove the air filter cover by loosening the knob that holds it in place. Remove and dispose of the air filter. Place the new air filter inside and replace the cover. If the air filter is not visibly dirty, check the maintenance schedule and replace the filter if it is time according to the schedule. Regular maintenance and replacement will keep the generator operating properly and efficiently, costing less to operate when airflow is optimal.This is a genuine OEM Generac part that is sourced from the manufacturer. It is sold individually and in packs of two. This air filter is for use in Generac personal generators.

Created for use with pressure washer by Generac, this fuel filter is an important component of the machine. A fuel filter has the responsibility of removing dirt and debris found in fuel so that it doesn't pass through to the carburetor. Having a maintained fuel filter in a pressure washer is important since even small particles could reach the carburetor. All fuel filters should be inspected on a regular basis and replaced about once a year.If the fuel filter needs to be replaced, the pressure washer should be placed on a level surface and the spark plug boot needs to be removed. Remove any fuel in the washer and then use a hooked piece of wire to pull out the fuel filter. Take the line in one hand while working to bring the filter out. Once it's out, put the new filter on the fuel line and work it inside. The filter will go into the tank and can be refilled with fuel before replacing the cap.This fuel filter is designed for use on Generac pressure washers. It is a genuine OEM product directly sourced from the manufacturer. It comes as a single individual part.

The way that a pressure washer works is simple, but there are also simple issues that can cause trouble with the machine. Pressure washers have both a water filter and an air filter to prevent debris from causing trouble in the machine. The air filter stops dirt and dust, as well as debris, from making it into the carburetor and causing the engine to run poorly or stall. As part of regular maintenance on a pressure washer's engine, it is a good idea to replace both the air and the oil or fuel filters. This is an OEM replacement part that will require a short amount of time and the use of a wrench set and pliers to make the change. This replacement pressure washer filter is designed to work with Generac pressure washers and effectively capture any contaminants that might enter the carburetor and then the engine itself. It works with a long list of Generac models, and is an easy part to replace.

This inlet screen prevents dirt, dust, and debris from entering the pump from the water inlet hose on many different Generac pressure washers. Any contaminants found in the garden hose that attaches to the pressure washer will be filtered out through the inlet screen so the water is clean and provided at the appropriate level of pressure. This part can get worn out or damaged and let in dirt and debris. If this happens, the inlet screen that connects to the hose will need to be replaced.If the pressure washer isn't providing the right water pressure, it can be a consequence of a damaged or dirty inlet screen. Detach the hose from the inlet valve and visually inspect it for problems. If there is an issue, the replacement will involve a set of pliers. The old inlet screen can be pulled out of the tool and replaced with this new replacement part. This inlet screen is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The screen is made for use with pressure washers manufactured by Generac.