Kenmore Dryer 110.71202011 (11071202011, 110 71202011) Parts

Replaced It With New One Read more

It took less then 15 min. Read more

• Noisy

Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more

Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer. Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more

After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

I undid the top with a putty knife, took out two screws and took off the front. I replaced the drum rollers and put the new belt on the drum, looped the belt on the idler and then onto the motor pulley. I also put on two new top hold down clips as the old ones broke because they were plastic, the new ones were metal. I took off the back panel and replaced the heating element. The hardest part was cleaning up all of the lint and dirt that had accumulated over the years. It was not difficult,... Read more

I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new... Read more

Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more

I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

Watched your very helpful and informative "how to" video and replaced both right and left hinges. Getting the front panel to line up on the clips was the most difficult part. Read more