Kenmore Dishwasher 665.13989K800 (66513989K800, 665 13989K800) Parts

The Upper Dishrack Rail is an OEM replacement part for Whirlpool dishwashers. It guides upper racks in and out for easy access to dishes. 

Causes of faulty rails can include worn rollers, broken clips, or stress cracks in modules after repeated cycles. 

Symptoms of a bad upper dishrack rail include:

• Difficulty inserting or removing the upper rack smoothly   
• Off-track movement that impacts washing coverage
• Detached ends or segments that compromise stability

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Air Vent Gasket is an OEM part for Whirlpool dishwashers. It is designed to seal the air vent, preventing water from leaking out during the dishwasher's operation. This gasket plays a critical role in maintaining the efficiency and effectiveness of your dishwasher by ensuring a watertight seal around the air vent, which is essential for the proper function of the venting system.

Causes of a bad Air Vent Gasket can include wear and tear over time, leading to cracks or deterioration, improper installation, which may result in a poor seal, or damage from harsh cleaning chemicals.

Symptoms of a bad Air Vent Gasket include:

• Water leaking from around the dishwasher's door.
• Dishes not drying properly due to compromised venting.
• Visible signs of wear or damage on the gasket itself.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement panel restores your appliance's original look while shielding internal components. Install a new panel to replace a dented, cracked, or missing piece and keep the assembly secure, aligned, and protected.

• Covers and protects internal parts while restoring the exterior finish and fit
• Provides the designed mounting surface for trim/handles; helps maintain alignment
• Replace when the panel is dented, cracked, warped, rusted, or mounting tabs are broken
• Helps resolve loose or rattling panels and visible gaps or misalignment

• Disconnect power; turn off water or gas supply if applicable
• Wear gloves and protect finished surfaces; handle carefully to avoid bending or scratching
• Transfer and reuse original screws, clips, insulation, and trim as directed by your service manual
• Fit and alignment before fully tightening fasteners

The Diverter Motor is an OEM part for Whirlpool dishwashers. It controls the movement of the diverter disc, which directs water flow to different spray arms during the wash cycle. This ensures that all areas of the dishwasher receive adequate water pressure for effective cleaning.

Causes of a bad diverter motor can include electrical malfunctions, wear and tear from frequent use, or damage from water exposure. A faulty diverter motor can prevent the proper distribution of water, leading to poor cleaning performance.

Symptoms of a bad diverter motor include:

• Dishes not being cleaned properly
• Unusual noises coming from the dishwasher during operation
• The dishwasher not advancing through cycles correctly
• Water not reaching all areas of the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Includes wire harness WPW10083167, Drain cap part number WPW10193605, and the shaft seal has been incorporated into sump housing, not available separately.

The Door Spring is an OEM replacement part for Whirlpool dishwashers. It assists in balancing and supporting the door during opening and closing motions. 

Causes of a bad door spring can include metal fatigue from years of compression and extension during cycles. The spring can also become misshaped if over-tightened during maintenance or installation.

Symptoms of a bad door spring for a dishwasher include:  

• Doors that slam shut too forcefully or rapidly
• Difficulty smoothly opening or closing the door  
• An imbalanced feeling when lifting or lowering the door

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper built-in dishwashers.

The Side Mounting Bracket Kit is an OEM part for Whirlpool dishwashers. It provides a secure and stable installation by mounting the dishwasher to the adjacent cabinetry or walls.

Causes of a bad Side Mounting Bracket Kit can include missing or damaged components, improper installation, or wear and tear over time.

Symptoms of a bad Side Mounting Bracket Kit include:

• The dishwasher rocking or shifting during operation
• Gaps or spaces between the dishwasher and surrounding cabinetry
• Potential safety hazards due to an improperly secured dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Tub Inlet Gasket is an OEM part for Whirlpool dishwashers. It ensures a watertight seal at the point where water enters the tub, preventing leaks and maintaining efficient water flow during the wash cycle.

Causes of a bad tub inlet gasket include wear and tear from regular use, damage from harsh cleaning chemicals, or drying out and cracking due to age.  

Symptoms of a bad tub inlet gasket include:

• Water leaking from the front or bottom of the dishwasher
• Poor cleaning results due to insufficient water pressure
• Visible cracks or wear on the gasket
• Unusual noises from the dishwasher during the filling cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head

The Door Hinge Assembly is an OEM part for Whirlpool dishwashers. This hinge assembly is responsible for attaching the dishwasher door to the main body, allowing it to open and close smoothly while maintaining a proper seal when shut. 

Causes of a bad door hinge assembly can include regular wear and tear, damage from excessive force or accidental impacts, and corrosion from exposure to moisture and detergents.  

Symptoms of a bad door hinge assembly include:

• The dishwasher door not closing properly or staying open
• Difficulty opening or closing the dishwasher door
• A misaligned dishwasher door
• Unusual noises or resistance when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Bracket is an OEM replacement part for Whirlpool dishwashers. Located inside the dishwasher tub along the edge, this bracket securely holds the entire detergent dispenser assembly in place. 

Causes of a bad bracket may be normal wear and tear over time, damage from overloading dishes, or accidental impact affecting the integrity of the plastic.

Symptoms of a bad detergent dispenser bracket include:

• Loose or unstable detergent dispenser  
• Detergent not dispensing or leaking
• Clanking noises coming from inside the tub
• Visible cracks, breaks, or deformations in the bracket 

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, and some Kenmore and Maytag models.

Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.

Shaft seal included.

The Adjuster Axle is an OEM part for Whirlpool dishwashers. It plays a crucial role in the height adjustment mechanism of the upper rack, allowing users to customize the rack's position to accommodate different dish sizes. This axle ensures that the adjustment is smooth and stable, providing flexibility in the dishwasher's loading capacity.

You should replace the adjuster axle if it becomes worn out or damaged. Causes of a bad adjuster axle can include wear from frequent adjustments, breakage from overloading the rack, or damage from mishandling.

Symptoms of a bad adjuster axle include:

• Difficulty in adjusting the height of the upper rack
• The rack not staying in the desired position
• Unusual movement or instability of the rack
• The adjuster mechanism not functioning properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dual tine positioner secures two rack tines together to keep dishes stable and properly spaced during the wash. Replacing a cracked or missing clip helps prevent plates and lids from tipping or rattling. What it does:

• Holds two adjacent rack tines in the selected position
• Helps maintain spacing for plates, lids, and trays
• Restores stable loading when the original clip is worn or broken
• Common symptoms: broken/missing clip, tines won't stay upright, items tip over or rattle

• One dual tine positioner clip

• Slide the rack out; remove the old clip by releasing its tabs
• Align the new clip over two tines and snap it firmly into place
• Spin the spray arm by hand to confirm clearances before running a cycle

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.