Kenmore Dishwasher 665.16023402 (66516023402, 665 16023402) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8580309
The Door Latch Strike is an OEM part for Whirlpool dishwashers. This part ensures that the dishwasher door securely latches when closed, maintaining a tight seal to prevent water leakage during the wash cycle.
Causes of a bad door latch strike include wear and tear from frequent opening and closing of the dishwasher door, accidental impact that can bend or break the strike, or buildup of debris that interferes with proper latching.
Symptoms of a bad door latch strike include:
- Dishwasher door not latching securely
- Water leaking from the door during operation
- Difficulty in closing or opening the dishwasher door
- The dishwasher not starting because the door isn’t properly closed
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Latch did not close properly causing dishwasher not to turn on and run Rani S. • Henrico , VA • March 24, 2020
I ordered this part and switched the previously used one.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400919
This small decorative cap covers an exposed screw on your appliance, restoring a clean, finished look and helping prevent snags. Replace a missing or damaged cover to keep panels tidy and screws protected.
- Conceals screw heads on the cabinet, console, or panel for a neat appearance
- Helps protect hands and clothing from catching on exposed screws
- Replace if the original cover is missing, cracked, loose, or discolored
- Installs by pressing over the screw head where used to sit flush with the surface
What's included: 1 screw cover Installation notes:
- Disconnect power to the appliance; shut off gas or water if applicable before servicing
- Gently pry off the old cover using a plastic tool to avoid scratching finishes
- Align and press the new cover until seated flush
- Do not force; re-align if resistance is felt to prevent damage
Do-It-Yourself Stories from Customers like You
The water parts were broken the washer is about 16 years old Katrina M. • Fontana , CA • July 14, 2018
We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set.
Read more
More
$6.95
- Compare At:
-
$8.34
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268321
This replacement mount secures the dishwasher's upper spray assembly in place, keeping it aligned so it spins freely and delivers consistent water coverage to the upper rack for dependable cleaning performance.
- Holds the up-spray/upper spray arm assembly securely inside the tub
- Maintains proper alignment and clearance for free rotation
- Common symptoms: upper spray arm loose or falls off, poor cleaning on the top rack, rattling from the arm striking the rack or tub, visible cracks in the mount
- Restores stable support after a worn or broken mount
What's included: 1 upper spray arm mount. Install notes:
- Disconnect power and water supply before servicing
- Remove the upper rack for access; release the old mount and transfer the spray arm if attached
- Seat and lock the new mount; verify the upper spray arm spins freely
- Run a short test cycle to confirm proper operation
Do-It-Yourself Stories from Customers like You
Dishwasher: upper wash came off/broke Carl M. • Peoria , AZ • November 08, 2015
Replaced wash arm mount
Read more
More
$53.33
- Compare At:
-
$63.46
- You Save:
-
$10.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10177098
The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.
Do-It-Yourself Stories from Customers like You
Dishwasher detergent dispenser Howard K. • Rockaway , NJ • November 01, 2015
Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself!
Read more
More
$10.41
- Compare At:
-
$12.28
- You Save:
-
$1.87
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.
Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.
Symptoms of a bad power cord include:
- The dishwasher not turning on or completing cycles
- Warm or hot power cords during operation
- Frayed, cracked, or exposed copper wiring
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Mice chewed the drain hose and power cord Noah C. • Eastsound , WA • February 16, 2015
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly.
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
Leaking around dishwasher door previous repair missing parts Patrick R. • Peachtree City , GA • November 15, 2014
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: W10871196
Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.
Do-It-Yourself Stories from Customers like You
I needed a toe kick panel for my maytag dishwasher Jeffrey C. • Plymouth , MN • May 02, 2016
I found the part number, double checked it, and ordered the part, which arrived as promised. However, the part was just placed in a folded cardboard tube and was damaged by the shipper. I figured it was only a toe-kick, so I bent the part as best I could and installed it in 3 minutes.
Read more
More
$85.62
- Compare At:
-
$102.74
- You Save:
-
$17.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10358302
Goes from pump to exterior drain hose.
Do-It-Yourself Stories from Customers like You
Dishwashwer was only partially draining James M. • Barre , MA • November 07, 2016
I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair.
Read more
More
$52.95
- Compare At:
-
$62.48
- You Save:
-
$9.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268909
Overfill control.
Do-It-Yourself Stories from Customers like You
Washer would not fill with water Ty J. • Hillsboro , OR • July 08, 2018
Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8531857
This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.
- Screens large food particles and debris from the pump/chopper inlet
- Helps maintain proper water circulation and consistent cleaning performance
- Reduces risk of pump damage or noisy operation from debris
- Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results
What's included: 1 inlet protector Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack and spray arm; access the sump/accumulator area per your model
- Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
- Reassemble and ensure the screen sits flat with no gaps
Do-It-Yourself Stories from Customers like You
Clogged at the chopper assembly strange noisehopper assembly broken Thomas H. • Idaho Falls , ID • July 07, 2015
Looked at Dishwasher. Scratched head and armpit. Told wife I would fix, not repariman. Wife skeptical - shook head. Found schematic on web. Found YouTube video of guy repairing same DW model. Disassembled. Diagnosed problem. Chopper assembly welded in place by water scale -broke removing. Potty mouth. Ordered parts. Waited for parts. Washed dishes by hand. Wife doing ok. Parts arrived (in only a day or two!!! Fed Ex for 7 bucks!! Great deal). Put on nasty t-shirt, baggy shorts. ...
Read more
More
$78.57
- Compare At:
-
$94.74
- You Save:
-
$16.17
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10477552
This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.
- Secures the wire/ring terminal to the heater stud for a solid electrical connection
- Helps prevent arcing, discoloration, and heat damage from a loose connection
- Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection
What's included: 1 heater terminal nut
- Disconnect power and allow the appliance and element to cool completely before service
- Photograph wiring for reference; remove old hardware and clean the terminal
- Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
- Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten
Do-It-Yourself Stories from Customers like You
Stopped running after rinse cycle and the clean light was flashed 3 times Clyde Y. • Turtle Creek , PA • August 29, 2015
Replaced the heating element as shown in the video. Repaired a bad connector on the wire leading to the heating element. The clean light still flashed 3 times. Determined that the thermal fuse also needed to be replaced. Replaced the thermal fuse as shown in the video. The clean light now flashed 7 times which I discovered meant that the control panel needed to be reset. I then reset the control panel by pressing the buttons: normal, heated dry, normal, heated dry. It now works perfectly.
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W10817436
This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.
- Fastens brackets, panels, and internal components to their mounting points
- Maintains alignment and reduces vibration during operation
- Replaces missing, worn, rusted, or stripped hardware
- Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supply if applicable
- Align the part being secured and remove any damaged hardware
- Hand-start threads to avoid cross-threading; tighten with the correct driver
- Do not overtighten; verify the assembly is secure and operates freely
Do-It-Yourself Stories from Customers like You
Wheel tub broken. Paul K. • Belleville , NJ • January 11, 2019
Replaced Wheel-Tub.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11027055
This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.
- Secures the heating element to its mounting point to keep it stable
- Maintains proper spacing from nearby components and surfaces
- Helps reduce vibration, rubbing, or rattling noises
- Replace if the original support is cracked, warped, missing, or the element appears misaligned
What's included: 1 heater support. Install notes:
- Disconnect power to the appliance before servicing; allow hot components to cool
- Access the heater per your model's service information; note the original orientation and routing
- Seat the support fully and handle element leads carefully to avoid damage
Do-It-Yourself Stories from Customers like You
Not cleaning well, silverware very bad. Walter M. • Labelle , FL • December 10, 2017
Replaced spray arms and tube. Found all had debris in them and prohibited water pressure from reaching items. After replacement everything comes out sparkling. Don't understand how the spray arms getting plugged. Almost like waste water is recycled. Turns out to be a very easy project and if needed AppliancePartsPro has information and directions available at your finger tips.!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268990
Bushing, Door spring
Do-It-Yourself Stories from Customers like You
Door spring was week or broke Ronald O. • Saginaw , MI • February 26, 2016
Purchased door springs from Appliance Parts pros.com, installed them and door on our Dishwasher was back to normal, Had to pull out dishwasher from under cupboard to get to springs, as they were on the sides of the dishwasher.
Read more
More
$57.22
- Compare At:
-
$68.09
- You Save:
-
$10.87