Lisa I February 28, 2013 for Model Number GLTF2940FSI Hello I have a Frigidaire front load Washer Model number GLTF2940FSI that is having a hard time maintaining its final spin. I have received the error code E47 but can't seem to find a place to search using that info just the option to search for the part needed and I have no clue what part that is :) After the washer attempts to spin (it moves side to side but never completes the full turn) it then turns off with 8 minutes remaining. I have 6 kids and desperately need my washer so please any advice would be greatly appreciated thank you so very much!
1 Answer Lisa, The E47 error code indicates that the board thinks the door PTC circuit is open in spin. To test you will remove door lock assembly and measure the resistance of th PTC. If shorted or open then replace the door lock assembly 131763256 and if it reads around 1500 ohms then replace main control 137006000. Read More...
Lucy December 21, 2012 for Model Number FTF2140es3 part 137005000 control board Hello, I receive the control board and is replacing the part now but I'm stuck unable to undo two pieces of plastic ties that are holding the wires together. These two ties are inserted in the back of the control board and seems impossible to remove unless I break them. Please help! Tks.
1 Answer Hello Lucy, Just cut the wire ties. If you want to replace them, you can order two 00411008. Read More...
I Bucek November 24, 2012 for Model Number ftf2140es3 my washer is running and washing ok, it does not spin laundry out properly. I have taken pump out and cleaned it had debris in it, after that it still does not spin fast enough to remove water from clothes. also lights on control panel come on by them self. what controls spin out speed of drum? Thanks I Bucek
1 Answer Bucek, The most likely issue is the motor control board 134743500, It may be as simple as a loose connection and the motor, motor control board or the machine control board 137005000NH.If you're sure the door locks and the washer drum drains, thats where you need to start. Thanks Read More...
Dave August 29, 2012 for Model Number FTF2140ES3 I just replaced the control board because of a E43 fault code. (unit shuts off when turned to normal wash cycles) New control board immediately starts beeping and the right side 5 led lights keep flashing 9 times (with the beeper). I cannot get this to stop, nor will it go into diagnostic mode. Other than a "beep", I get no response from any button pushed. I have checked and rechecked all wires and pins/terminals. Any help would be greatly appreciated.
1 Answer Hello Dave, There seems to be some controversy over the fault codes. Some are claiming it is the fault of the individual reading the codes and others say it is the fault code list being wrong from the manufacturer. Regardless of who is at fault, the problem seems to be that while the fault code says to replace the control board, the door lock assembly should be tested to make sure it isn't the cause of the issue. If it tests out good, the control board in the bottom of the machine which is referred to by Frigidaire as the speed controller, is the board that should be replaced. As I said, the control board should not be replaced until the cheaper part is tested. Testing it is as follows: Access the door lock assembly and measure the resistance of the wax motor on the assembly. You will need a resistance meter to test it. If it reads 1500 ohms, give or take 10%, then its fine, and the problem would be the speed controller, (control board in the bottom of the unit). Read More...
Denis June 24, 2012 for Model Number ltf2140es3 I get nothing. I have power at the outlet. I don't have any power indication on the front panel.
1 Answer Hello Denis, You need to open the main top of the unit and check to see if you have power to the J14 terminals C2,1 and C2,2. There should be 120Vac here as this is where the ac voltage is supplied to the control. If the voltage is there, you will need to replace the main control board 137005000NH. If it isn't, replace the power cord 5304505407. Read More...
Jai June 23, 2012 for Model Number FTFB4000FS1 My washer will go through the wash cycle but does not do a final spin cycle , I checked the filter and there is nothing in it. Even when I manually put it in rinse cycle it will let a few drops of water in and just sits ,it will not cycle, the door light does not come on to indicate there is a problem with door switch. So what is the matter with my machine?
1 Answer Hello Jai. It sounds like you either have an issue with the water valve not filling the unit, or the door lock assembly is bad and will need to be replaced. Check and see if the valve is not filling the unit with cold water. If the valve is working properly, and the drain pump is working properly, you will need to replace the door lock assembly 131763256 on the unit. Read More...
Al May 22, 2012 for Model Number ltf2140es3 washer will not start the door light will not come on and beeps 3 times I changed the door lock thinking that was it but was wrong washer will not go into diagnastic mode just beeps 3 times.
1 Answer Al, First check and make sure there are no loose connections on the wiring between the door lock assembly and control board. Make sure the loading door and hinges are aligned to the door opening and front panel, The replace the control. The control is not seeing the door switch activate and de activate. Thanks and Good Luck Read More...
Kelly April 19, 2012 for Model Number ATF6000ES0 Drain pump humming but not working. Is my pump bad or what else could it be?
1 Answer Hello Kelly. Check and make sure the filter in the hose attached to the pump is not clogged and preventing the pump from running. If not, and the drain hose is not clogged, you will need to order and replace the pump 137221600 on the unit. Hope this helps. Read More...
Doug B March 12, 2012 for Model Number FTF2140ES0 Ran diagnostics tests and tub does not or turn when it is supposed to spin and it comes up "error code 95" which is listed "control board". However I see that there is a control board and a motor control board so which do I order for E95?
1 Answer Doug, when it comes to a communication error between the board (E95) the motor control 134743500 is usually the culprit. If you're sure you have no loose connections or corrosion on the connectors at either board, The motor control is where to start. Thanks and Good Luck Read More...
Terry December 11, 2011 for Model Number FTF2140ES3 When I go to start my washer and I push the start button all it does is flash and all the lights come on when only the lock light and wash should be lit up to start. Can you tell me why this is happening. Thank you for your help
1 Answer Hello Terry. Check and make sure the door lock assembly 131763256 is good on the unit. If so, you will need to replace the control board 137005000NH. Also, make sure the dispenser is closed all the way. Hope this helps. Read More...