Alexander February 19, 2024 for Model Number 795.71603.012 I replaced the water valve and water line from valve to icemaker after water was leaking from the back of the fridge (where the supply line enters the back of fridge. Ice maker seemed to be overfilling due to valve not closing quickly enough. New water solved problem. Immediately following this repair, I now have ice that smells and tastes bad. This is a short term rental, and there is no food in the fridge or freezer. The inside is very clean. Also this model does not have water filter. Any idea why the ice smells and tastes bad?
1 Answer Alexander, There should be nothing in the part that could cause this issue. The smell and or taste issue would be from the water or airborne source. Read More...
Tp December 16, 2023 for Model Number LHTNS2403S I think this is the valve i need. I only need the wiring harness, if you can make an exception, jjst the 2 end connectors
1 Answer TP, the water valve MJX41869208 would be used with the model number provided and the wire would not be available separately. Read More...
Sara February 24, 2023 for Model Number LFC21776ST I recently replaced the water valve on the refrigerator because the water to the ice tray wouldn't turn off. It makes ice but doesn't freeze it completely before dumping. Is the ice maker bad? What else should I check?
1 Answer Sara, Thanks for asking!!! Yes, you likely need to replace the icemaker as a temperature sensor is built into it. Check your model revision number to get the correct icemaker. Read More...
John W August 12, 2020 for Model Number LFC28768ST Ice cubes being made are not real smooth, and when cubes drop some water seems to spill on top, creating a large useless clump of cubes. Suspecting that water pressure was high I placed a valve in the water feed line to reduce flow but didn’t do any good. Is replacing the valve AP4444451 the probable solution, or perhaps is there some clog internally in the ice maker where just replacing the entire unit would be the fastest fix?
1 Answer John, yes I am betting that it is the water valve not closing quickly enough due to internal wear. Unfortunately, there is no good way to test for it. I would replace the valve first then the icemaker only if needed. Read More...
Victor May 02, 2020 for Model Number Lg lfcs25426d Hello-looking to replace my water inlett valve and ice maker and am wondering what the correct part numbers are?
1 Answer Victor, The water valve for this unit will be part number 5220JB2010A and the ice maker will be part number AEQ72909603. Read More...
Richard May 19, 2018 for Model Number LFC21776ST Our ice maker has not been working, I'm trying to get it fixed. We turned it off because of water dripping/leaking onto the floor behind the refrigerator. Now i've turned it back on, it is not leaking but the water tray is not really filling and the whole ice maker makes 1 itty bitty cube at a time. Is it the water intake valve that needs replacing? I'm looking at part # 5220JB2010A
1 Answer Richard, You will want to look for corrosion on the water valve on the back of the unit. This would be the most likely cause for leaking. Also check the fill tube for being frozen which would also be caused by a faulty water valve. Read More...
Don H. February 03, 2017 for Model Number LG LFC25765 I just wanted to be sure I am ordering the correct part because when I put my model number into the comparability tool it tells me it is NOT compatible. I have the LFC25765 French door refrigerator and wish to replace the water intake valve which supplies the water to the ice cube maker and I am looking at part AP4444451 is that correct? I also wish to replace the tubes and I was refereed to part WR17X1948, is that the correct part for the supply lines for my model refrigerator? Thank You
1 Answer Hello Don, The water valve is AJU55759303, icemaker AEQ72909603, and fill tube AJU73753101, (which is no longer available). Since these part numbers have crossed by the manufacturer from the part numbers on the original parts list for the model number, the compatibility tool will not recognize the part as being compatible with the model number. The compatibility tool is still in work and we apologize once again. Read More...
Nancy September 26, 2016 for Model Number LFC525770SW The water line that goes to the ice maker is the problem. The connector where it attaches leaks water. It seems to be corroded. What piece needs to be replaced?
1 Answer Hello Nancy, If your model number is actually LFC525770SW, you will need to order water valve 5220JB2010A. If the model number is different, we will need to re-verify the part number to prevent ordering the wrong part for your unit. Read More...
Ken August 28, 2016 for Model Number LFC25760ST This is a follow-on to question asking How can I tell if the valve is bad or the ice maker is at fault? In the answer, it refers to checking to see whether there is power going to the valve when the ice maker cycles. Is there any way to force the ice maker to cycle, so that I know when to check? Turing the unit off then back on? How do I know if the ice maker is cycling? Is that when the tine arm rotates, to scoop the cubes our of the slots where they form? In my case, I don't seem to see anything whatsoever when I turn the unit off then back on; rather, it just sits there, with the ice slots empty....... (Last time we had something go wrong with refrigerator at our old home, replacing refrigerator (instead of part) led to re-doing the whole kitchen. Perhaps my wife is behind this......... :) )
1 Answer Hello Ken. Make sure the freezer is between 0° and 5°. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. To cycle the icemaker, you have a test button on the bottom of the icemaker head. You press and hold the button until the icemaker starts to cycle. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Hello The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...