Customer Questions and Answers for Oven Igniter by Whirlpool

Best Seller

Manufacturer Part

Oven Igniter

4.89 (64)

By: Whirlpool

Part Number: OEM18111615

Manufacturer Part Number: W10918546

The Oven Igniter is an OEM part for Whirlpool ovens responsible for igniting the gas burner that heats the oven. It works by drawing electrical current through the igniter filament, heating it to a high temperature until it glows and ignites the gas to start the cooking process.

Symptoms of a failing Oven Igniter include:

Oven not heating up at all
Igniter glowing without igniting the gas
Weak flame or delayed ignition
Increased gas smell

Causes of a bad Oven Igniter can range from normal wear and tear, which reduces the igniter's efficiency over time, to physical damage or a buildup of dirt and grease that can interfere with its operation. A malfunctioning igniter can lead to uneven cooking, wasted gas, and in some cases, safety hazards due to the accumulation of gas without ignition.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

$41.95

Compare At:: $49.92
You Save:: $7.97

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Questions & Answers

For Whirlpool Oven Igniter (Part Number: OEM18111615)

Len B. January 26, 2013 for Model Number ans.721.1a-1991

i'm looking for replacement igniter, bake and broil. they are different lengths,flat type. can not find due to being discontinued for some time? is there another model and part number that can be used to replace these? thank you len

1 Answer

Len, You may want to try a couple of these 12400035, with all the extrs connectors, wire nuts and insert, they're pretty much a "universal" fit. Since most "flat" type igniters are rated at 3.2 to 3.6 amps they should work in your range. The model number you supplied is not correct, so that's about the best we can do, for now. Thanks

Rose November 14, 2012 for Model Number 774t117p or 774t120p

My oven no longer heats up. I believe I need an ignitor. The model number was given. However, I can't find it. It is from a Tappan range oven. Is there another ignitor compatible to this one? I would like to do some cooking for Thanksgiving. Hope you can help. Thanks.

1 Answer

Rose, model number 774t117p does not pull up in our system. I googled this model and found igniter part number 316T023P05 and 5303935067. We have images available of each product you may view by clicking on the part numbers. If the model number given was from the igniter please locate your model number to your appliance and feel free to repost for further verification. Thanks!

Duque October 26, 2012 for Model Number sf315pepq2

The oven had issues getting started. If we start the top burners sometimes it will come on.. It seems like that is the only thing that will get it to ignite.. That worked for awhile, however now it takes longer to get it ignited.. Does it need a new igniter? Or what would you suggest..? Is this something we could fix?

1 Answer

Duque, It sounds like you may have two issues, a weak igniter W10918546 and or a faulty gas pressure regulator W10624131 Start by replacing the igniter, it's the more likely issue, and it is an easy repair, and something you can do. Remove the oven door, remove the oven bottom panel, remove the flame spreader, and you'll have access to the igniter and can replace it.

Bruce R August 01, 2012 for Model Number sf114pxsw2

just replaced the ignitor,used it this morning,code number f2 came up beeping,could not get it to stop. had t0 unplug it,what do,s code f2 mean @ how do i fix it.

1 Answer

Bruce, the F2 Diagnostic code indicates an issue with the touchpad assembly "F2 - Shorted key ". Your control is a single piece control and touchpad assembly WPW10335164. You'll need to replace the control to solve the issue. Thanks

Bruce August 01, 2012 for Model Number sf114pxsw2

put in new part,frist time to use it,after warm up,it started beeping and would not stop,code f2 on front of stove,what's it mean?

1 Answer

Bruce, The F2 code on your range indicates a failure in the control WPW10335164, But, you may want to check or replace the oven sensor first WPW10181986. The resistance should be less than 1100 ohms resistance at room temp. We'll send you the data information sheet, that will give you a better understanding of the system and operation of the range.

Jeff July 17, 2012 for Model Number sf315pemw1

When I replaced the ignitor, I was given a similar GE ignitor installed it and it seemed to work, but I found that it runs all the time even if the stove is turned off and it continues to heat up.

1 Answer

Hello Jeff, This has to be a bad gas valve WP98014893. If it were anything else, the thermostats would have kicked it off. If the valve is stuck open, when the thermostats are open so the valve would normally close, it has to be still open.

Joyce L. June 22, 2012 for Model Number Tappan TGF336AUG

My oven takes a long time to light when it does light, I smell gas sometimes, I can take a wooden spoon and tap on the tube above the safety valve and it will start.When it gets to that temp and shuts off it will not restart unless I tap it again it seems as though it takes a long time to preheat when I do get it to light. I removed the safety valve and cleaned it put it back in and it worked good for a while then it started the same thing again what does it sound like to you, Thanks.

1 Answer

Hello Joyce, You need to replace that safety valve 5304521339. The manufacturer doesn't even want qualified technicians tampering with it as it creates a gas leak, fire, burn, and explosion hazard.

Bart June 07, 2012 for Model Number Magic Chef Model #31203PAV

Will this oven igniter work with Magic Chef Model #31203PAV?

1 Answer

Hello Bart. No, based on the model number, 12400035 is the correct igniter.

Confused March 17, 2012 for Model Number sf377pegz1

Hi, do you know if this will work to replace an existing round type igniter? Turns out my oven uses a round type and I bought the wrong type. Thanks.

1 Answer

Hello! For the listed model SF377PEGZ1 you will need to use the round igniter, part number 4342528. If you purchased the flat igniter WP3186491 with our company you may return the item at anytime. Here is our return policy link for you to view our return policy and to get started on your return. Thanks! http://www.appliancepartspros.com/customerservice/returns.aspx

Dora R. May 24, 2011 for Model Number sf111pxsq1

Yes I just install a new oven ignitor in my whirlpool stove I tryed it out but nothing happen it will not do anything, it simple to install... Can you help me?

1 Answer

Hello Dora. You will need to test and see if there is 120 volts coming to the igniter. If not, you will need to replace the thermostat WPW10641988. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Have questions? Ask our pros!

Call us 1-877-477-7278

Need Help? Chat with a Pro

Or ask a question by filling in the form

Share your thoughts with other customers

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Customer Questions and Answers for Oven Igniter by Whirlpool

Oven Igniter

Questions & Answers

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

1 Answer

Have questions? Ask our pros!

Or ask a question by filling in the form

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Customer Questions and Answers for Oven Igniter by Whirlpool

Questions & Answers

Have questions? Ask our pros!

Or ask a question by filling in the form

Ask your question