Shaun February 01, 2023 for Model Number WDT750SAHW0 What is the size of the THREADED part the inlet valve and are the threads male or female?
Xacozelman January 20, 2023 for Model Number Maytag I found the wires @ the inlet valve have been severed by rodent & the remainig wire on the selinoid is too short to effect a splice so replacing the selinoind seems the obvious solution - but I don't know how to order it? I can provide the serial # & model # to make the order.
1 Answer xacozelman, To be able to assist you with the part number we will need to have the model number of your unit. Please resubmit your question with the model. Read More...
Geoc July 19, 2022 for Model Number KitchenAid KUDS30IXBL0 I get Error Codes 6 then 1 and 6 then 2 which would indicate Water Inlet Valve is not working. However, whatever cycle I choose, water fills, washes and drains on the first wash (rinse), but does not perform (fill) on any subsequent parts of the cycle. Wouldn’t this indicate that the problem is more than solely the inlet valve, since the valve seems to work on the first portion of any cycle?
1 Answer GeoC, the valve WPW10327249 would need to be tested for 120VAC during a refill cycle. If there is voltage and the valve did not allow water through, the valve has failed. If there is not 120VAC, the float would need to be inspected to identify if it is getting stuck in the upward position. If it is not stuck in an upward position, the main control WPW10380685 would be the most likely cause of failure. Read More...
Steve September 06, 2021 for Model Number JDB8000AWB1 Our Jennair dishwasher makes a high pitched whirring sound right at the start of a wash cycle, but stops once the washer has filled with water. Could this be the water inlet valve?
1 Answer Steve, Thanks for the question and based on the description it could be the valve but it also could be the water pressure, I would check the pressure first. Read More...
Sam Hale May 01, 2021 for Model Number KUDS30FXSS8 Press start, dishwasher appears to start but moves to drain immediately.
1 Answer Sam, The unit will start off with a short drain before it fills and starts washing. If it is going straight to drain after filling then this will most likely be an issue with the control board. Read More...
Thomas February 18, 2021 for Model Number GU2275XTVY1 Water appears to be dripping from the water inlet valve on the dishwasher. Is this a sign of a failed water inlet valve?
Tracey October 27, 2020 for Model Number KDTM354ESS3 Water is coming in sounds like it want to wash but it just does nothing. Not sure how much should be in the bottom but the water does make it to the float, but the float does not rise. I drain it turned the power off then back on nothing. Could my lower arm be clogged. We have a water softener and whole house water filtration system. This dishwasher is just three years old. Second time it has stopped on us.
1 Answer Tracey, it is possible that the lower wash arm W11553338 is clogged up and this can be checked. Another check that can be done is checking to ensure there is not a clog in the sump that could be preventing water flow through the circulation pump W10902589. If there is a clog in the sump, or an item preventing the impeller W10783130 from rotating properly, it would need to be cleared and the appliance tested. If there are no clogs and the impeller is not damaged, it is likely that the circulation motor has failed if it is receiving 120VAC from the main control W11341628. Read More...
Alan October 27, 2020 for Model Number WDT710PAYM3 I replaced the water inlet valve as directed but nothing is happening. The dishwasher makes a grunting sound a couple of minutes after hitting start and then shuts down. What is the next step? Thanks
1 Answer Hello Alan, If there are no harness issues, the control W10479763 will have to be the issue since the fill circuit is made up of the water valve, the control, and the wiring harness. Read More...
James September 23, 2020 for Model Number WDTA75SAHN When the dishwasher fills, it makes banging noise when the water shuts off. Other than that, the dishwasher works good. Could it be a problem with an intake valve? How can I find out what the problem is?
1 Answer Hello James, the water valve is working correctly if it opens to allow fill and closes with no leak, this however sounds like a plumbing problem, specifically, water hammer, which has various causes, high water pressure, loose water pipe mountings in-wall/floor, if that is the case there are water hammer arrestors of various types available in the plumbing aisle of home improvement stores. Read More...
Curtis July 02, 2020 for Model Number KUDS30IXSSA I have a dishwasher that seems to be not cleaning the top rack of dishes. The bottom rack is cleaning and the soap seems to be dissolved and used. I noticed that the water manifold probe was broke and the water supply tube had a piece missing. I ordered those parts and replaced them. I ran the dishwasher a few times after doing this and top rack dishes are still not getting cleaned. What do you think it might be? I seem to be getting water coming in so it is filling. Could you please give me some ideas or other things to check? Thank you
1 Answer Curtis, if there is not a crack in the water tower housing going up to the middle and upper spray arms, the next step would be to inspect the impeller assembly 8193951A to identify if there is a loose, broken, or a congested section. Read More...