Range Burner & Related Parts

The Burner Head is an OEM replacement part for Whirlpool gas ranges. This is the smaller burner head and it distributes gas evenly through the ports to produce a focused and consistent flame for temperature control during cooking.

Size: Small

Due to spills, grease buildup, corrosion, or wear and tear, the small burner head can deteriorate, clogging its ports and affecting gas distribution. When this occurs, the burner head may struggle to maintain a steady flame, impacting cooking performance.

Symptoms of a faulty Small Burner Head include:

• Uneven or low flames on the small burner
• Difficulty igniting the burner
• Clogged ports or visible rust/corrosion

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Gas Range LP Conversion Kit is an OEM part for specific Whirlpool gas ranges. It allows built-in ranges fueled by natural gas to be safely converted for use with liquid propane (LP) fuel. 

Symptoms requiring an LP conversion would include: 

• Inability to ignite or achieve proper combustion using natural gas 
• Unstable burner flame patterns or inconsistent heat output
• Gas leaks or improper connection to an LP fuel supply

Causes for needing an LP conversion kit include choosing to install the range in an area only serviced by LP gas, rather than natural gas. Additional causes could be wear and failure of the original equipment over time.  

This OEM kit is compatible with select Maytag, KitchenAid, Jenn-Air, and Kenmore gas ranges.

This cooktop is the main top panel for gas units. It supports the burners and grates, helps contain spills, and restores a clean, safe cooking surface when the original top is chipped, dented, or corroded.

• Serves as the primary surface where burner heads, caps, electrodes, and grates mount
• Contains spills and shields internal components from heat and debris
• Restores proper fit if grates or burners no longer sit level
• Typical reasons to replace include chips, cracks, warping, severe staining, or rust

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; note screw locations and igniter lead routing
• Lift off the old top and transfer any brackets, grommets, or insulation as required
• Reassemble carefully and perform a leak check at burner connections after installation

This LP conversion kit converts a compatible natural-gas range or cooktop to run on liquid propane, restoring correct fuel flow and burner performance for homes using bottled propane. It provides the parts needed for proper gas type change. What it does:

• Replaces or adjusts burner fuel delivery so the appliance operates safely on liquid propane
• Restores correct flame characteristics and heat output after conversion
• Helps resolve symptoms like burners that burn poorly, produce yellow or sooty flames, or have reduced heat on the wrong gas type
• Supports safe operation by allowing proper jet/orifice sizing and regulator settings for LP

• Conversion kit components required to convert a natural-gas range or cooktop to liquid propane

• Conversion must follow the appliance's OEM instructions exactly; keep the manufacturer's supplied procedure and torque/adjustment notes
• Require basic tools; some kits need orifice removal/installation and regulator adjustment
• Shut off gas supply and disconnect power before starting work; check for leaks after conversion using a soap solution

This burner cap kit replaces worn or damaged black burner caps on gas cooktops to restore proper flame shaping and even heat distribution for safer, more reliable cooking. Fits select gas range burner configurations. What it does:

• Covers the burner head to help direct and shape the flame for consistent heating
• Protects the burner base from spills, corrosion, and debris that can affect performance
• Helps reduce flare-ups and uneven cooking caused by damaged or missing caps
• Resolve visible flame irregularities, poor ignition, or partial burner shutdowns

• Turn off the cooktop and gas supply and allow components to cool before servicing
• Remove old caps, clean burner head and surrounding area, then seat new cap flat and centered
• No special tools typically required; check fit and ignition before full use

This D simmer ring fits the cooktop burner to help control and focus the gas flame for low-heat cooking and simmering. It restores proper burner alignment and helps prevent uneven heating on compatible gas ranges. What it does:

• Centers and supports the burner cap so the flame burns evenly
• Narrows the flame for low-heat/simmer settings and gentler cooking
• Helps reduce hot spots and improves stove-to-pot heat transfer
• Resolves uneven or wandering flames when the original ring is warped or damaged

• Turn off all controls and ensure the range is completely cool before servicing
• Remove grate and burner cap, seat the simmer ring over the burner base, then replace cap and grate
• Inspect for cracks, warping, or heavy corrosion; replace if damaged
• If you smell gas or the flame remains abnormal after installation, stop use.

The Burner Cap is an OEM component specifically designed for Whirlpool gas ranges. Located atop each surface burner element, it creates an ideal heating footprint optimized for common cookware.

Symptoms of a faulty burner cap often include misshapen or distorted areas from prolonged exposure to high temperatures. Discoloration or scaling along outer rims occurs as well from mineral accumulation over many years.

Symptoms of a bad burner cap include:

• Caps appear badly twisted or misshaped
• Grime builds up in hard-to-clean sections
• Flame patterns become irregular or unstable
• They show signs of cracking

This OEM Whirlpool replacement burner cap restores safe, uniform heating. Installed promptly to remedy burners scorched underneath, it averts continued performance compromises from further damage or debris traps. 

Compatible also with some GE and Frigidaire range models, this part maintains efficient energy use for cooking convenience. 

This burner top is the cooktop surface component that holds and aligns a single surface heating element, restoring safe, even heating and a finished look to the cooktop. It's a direct-replacement top piece for one burner location. What it does

• Supports and centers the surface burner so cookware sits flat and heats evenly.
• Protects internal cooktop components from spills and drips.
• Helps maintain proper spacing between the element and cooktop for reliable operation.
• Replace when the top is warped, cracked, badly corroded, or interfering with burner contact.

• One burner top

• Disconnect power to the range before starting any repairs; for gas ranges, turn off the gas supply.
• Handle enamelled or glass surfaces carefully to avoid chipping or cracking during removal and installation.
• Confirm element alignment and secure mounting so the burner element makes proper contact.

The Burner is an OEM part for Frigidaire gas ranges and cooktops. It is a stainless steel component that emits radiant heat from below the cooktop grates, facilitating safe, efficient cooking. 

Proper burner operation is essential for dependable cooking performance. The burner utilizes a gas control valve and orifice to deliver a precisely regulated flame that heats pots and pans quickly and evenly.

Causes of a bad burner can include cracks or holes developing from use over time, or damaged brass burners from spills or heat exposure.

Symptoms of a bad burner include: 

• Irregular or uneven cooking temperatures
• Burner flames that are too high or low  
• Yellow flame tips instead of blue
• Non-selective control or inability to adjust flames

Replacing the burner with a genuine Frigidaire part restores robust heat output. This ensures safe, efficient operation. It is also compatible with Gas ranges by Electrolux, Gibson, Kelvinator, and Kenmore.
 

This burner base holds the surface burner assembly in place and helps route gas to the burner for safe ignition. It restores proper burner positioning so the cooktop lights and heats reliably. What it does

• Supports and locates the surface burner head and cap for correct flame formation
• Directs gas flow from the valve to the burner ports for consistent ignition
• Commonly replaced if the burner sits unevenly, won't light reliably, or flame is irregular
• Works with associated burner components to ensure normal operation

• Turn off the appliance gas supply and electrical power before beginning work
• Verify correct fit and orientation; seat the base fully before reinstalling burner head and cap
• Use basic hand tools; tighten fasteners securely but avoid over-torquing

The LP Conversion Kit with Instructions is an OEM replacement part for Frigidaire gas appliances. This kit is designed to convert a natural gas appliance to operate with liquid propane (LP) fuel. It includes all necessary components and instructions for a safe and effective conversion, ensuring optimal performance with propane.

Causes for needing an LP conversion kit typically include a change in the type of gas supply, such as moving to an area where propane is the primary fuel source. Proper installation is crucial to maintain safety and efficiency during operation.

Symptoms indicating the need for this kit include:

• The appliance is not functioning due to an incompatible gas type
• Incorrect or inconsistent burner flames
• Relocation to an area with propane-only gas service

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This medium crown burner sits on the gas cooktop/range burner to shape and distribute the flame for even heating. Replacing a worn or damaged crown restores reliable ignition and a consistent flame pattern on the medium-output burner.

• Distributes gas evenly around the burner for steady, uniform heat
• Works with the igniter for reliable lighting when properly seated
• Helps protect burner ports from spills and debris
• Helps with uneven or yellow flames, delayed ignition, inconsistent lighting, or visible cracks/warping

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the old crown and clean the mating surfaces
• Align the new crown with any locator pins/notches and seat it flat; if screws are present on your model, tighten gently and evenly
• Restore gas/power and test for proper ignition and flame pattern

Orifice spud secures the burner orifice to the gas valve/manifold and directs fuel to the burner for proper flame performance. Replaces a damaged or corroded spud to help restore correct gas flow at the burner. What it does:

• Holds the burner orifice in place and channels gas from the valve to the burner.
• Helps maintain consistent flame size for even heating and cooking.
• Commonly used when a burner has weak, uneven, or intermittent flame performance.
• Replace if the spud is cracked, corroded, damaged, or leaking.

• Turn off the appliance's gas supply and disconnect power before beginning any repairs.
• Remove burner components per the service manual and install the spud in the same orientation as the original.
• Hand-start threads, then snug with the appropriate wrench—do not overtighten.
• After installation, check fittings for leaks with an approved leak-detection method; if you smell gas or suspect a leak, stop.

The LP Conversion Kit is an OEM replacement part for Whirlpool cooktops. It allows you to convert your cooktop from natural gas to LP gas, ensuring compatibility with your available fuel source. It includes all the necessary parts and instructions to safely and effectively convert your cooktop.

Causes of needing a conversion kit include:

• Switching from natural gas to LP gas as the fuel source
• Moving to a new location with different gas supply requirements

By using this LP conversion kit, you can enjoy the versatility and convenience of using LP gas on your Whirlpool cooktop.
This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Cap-Burner is an OEM replacement part for Frigidaire cooktops. It is a component located at the top of each burner element on the cooktop. The cap-burner sits directly over the burner element to distribute and maintain heat levels evenly across the heating surface. 

Causes of a bad cap-burner can include warping or distortion from excessive heat exposure over time. Wet or sticky messes can also lead to clogging or blockages.

Symptoms of a bad cap-burner include: 

• Uneven or inefficient heating of pots and pans placed on the burner surface
• Hot spots or areas of excessively high heat 
• Burner elements that do not ignite or power on as expected
• Smoke or burning smells coming from below the cap-burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.