Washer Liquid Valve Parts
Genuine Ge part
By: Ge
Part Number: WH13X10053
The Triple Water Valve is an OEM part for GE washing machines. This valve controls the flow of hot, cold, and warm water into the washer, ensuring the correct water temperature and volume for each cycle.
You should replace the triple water valve if it becomes faulty. Causes of a bad triple water valve can include mineral buildup from hard water, wear and tear from regular use, or electrical malfunctions affecting the valve's solenoids.
Symptoms of a bad triple water valve include:
- The washer not filling with water or filling slowly
- Incorrect water temperature during cycles
- Water leaking from the valve area
- No water flow when the cycle starts
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ge top loading washer slow drip leak from top of tub when off Matthew E. • Alexandria , VA • May 14, 2016
GE Top Loading Washer, slow drip leak from top of tub when off; ordered triple water valve. Removed 3 hex screws behind top control panel (in back); removed 2 rear hex screws on back of control panel. Removed hoses and plug. As you move panel forward, its lower tabs slide sideways in order to remove/roll panel forward. Unplug hot and cold wire harness leads. Unscrew 2 Phillips head screws. Removed hose clamp--BE CAREFUL--as you remove the hard plastic hose from the Triple Valve. Removed...
Read more
More
$45.95
- Compare At:
-
$54.68
- You Save:
-
$8.73
Genuine Frigidaire part
By: Frigidaire
Part Number: 134637810
The Water Dispenser Valve is an OEM part for Frigidaire washing machines. This valve controls the flow of water into the washing machine during the wash and rinse cycles. It ensures that the correct amount of water enters the drum, contributing to efficient and effective cleaning.
Causes of a bad water dispenser valve can include mineral deposits or debris clogging the valve, wear and tear over time, or electrical faults that affect the valve’s operation.
Symptoms of a bad water dispenser valve include:
- No water entering the washer
- Insufficient water during cycles
- Leaks around the valve area
- Inconsistent water flow
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking water dispenser inlet valve on washing machine Grete C. • Douglasville , GA • August 28, 2014
After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part...
Read more
More
$119.47
- Compare At:
-
$143.36
- You Save:
-
$23.89
Genuine Samsung part
By: Samsung
Part Number: DC62-30314K
The Washer Water Inlet Valve is essential for maintaining a steady and reliable water supply to your Samsung washing machine. This genuine OEM part ensures compatibility with a wide range of Samsung washer models, providing a perfect fit and seamless integration. Crafted from high-quality materials, the valve effectively controls the water flow, preventing leaks and ensuring that your washer operates efficiently during each cycle. Installing the Washer Water Inlet Valve can resolve issues such as inadequate water filling or inconsistent water levels, restoring your applianceGÇÖs optimal performance. Its durable design not only enhances the longevity of your washer but also minimizes the need for frequent repairs. Choosing this genuine OEM part guarantees that you receive a product that meets SamsungGÇÖs exacting standards, offering peace of mind and dependable functionality. Upgrade your washer with the Washer Water Inlet Valve to enjoy efficient washing cycles and extend the life of your appliance.
Do-It-Yourself Stories from Customers like You
Samsung washer wasn't getting hot water anymore Scott S. • Palo Alto , CA • April 25, 2014
I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in...
Read more
More
$90.63
- Compare At:
-
$107.85
- You Save:
-
$17.22
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304528029
The Water Valve is an OEM part for Frigidaire washing machines. This part controls the entry of water into the washer during the wash and rinse cycles.
Common causes of a bad valve include mineral deposits from hard water, electrical issues, or general wear and tear over time.
Symptoms of a bad washer water valve include:
- Washer not filling with water
- Slow water fill rate
- Leaking water from the valve area
- Inconsistent water temperature
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Water leak Matt C. • Simpsonville , SC • January 05, 2026
Replaced intake valve
Read more
More
$127.27
- Compare At:
-
$151.45
- You Save:
-
$24.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10110225
The Water Inlet Flow Meter is an OEM part for Whirlpool washing machines. It is responsible for monitoring and regulating the flow of water entering the washing machine during the fill cycle, ensuring the correct amount of water is added for efficient and effective cleaning.
Causes of a faulty Water Inlet Flow Meter include sediment buildup, physical damage, or electrical issues with the meter's sensors or connections.
Symptoms of a bad Water Inlet Flow Meter include:
- Incorrect water levels in the wash tub
- Washing machine not filling properly with water
- Error codes related to water inlet flow or water level issues
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Unnoticed leak until i removed the top of my front end washer George V. • Homestead , FL • January 03, 2015
This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap...
Read more
More
$76.95
- Compare At:
-
$92.34
- You Save:
-
$15.39
Genuine Ge part
By: Ge
Part Number: WH13X10024
The Water Inlet Valve is an OEM part for GE washing machines. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.
Symptoms of a failing Water Inlet Valve include:
- The washing machine not filling with water or filling very slowly
- The washer filling with water even when it is turned off
- Water leaking from the valve area
- The washing machine displaying error codes related to water supply issues
- Inconsistent water temperatures during cycles
Causes of a bad water inlet valve can include mineral deposits or debris clogging the valve, wear and tear on the solenoid coils, or electrical issues such as faulty wiring or connections.
This OEM GE part is also compatible with some models from Hotpoint, RCA, and Kenmore.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
There was a small water leak into the tub when the washer was off Jack C. • Atlanta , GA • July 16, 2014
Ordered water inlet valve. Two screws to take out. Disconnect the hose. Disconnect the two wires. Put in the new valve. Reverse the procedure. Whole thing took about 10 minutes.
Read more
More
$76.44
- Compare At:
-
$90.96
- You Save:
-
$14.52
Genuine Frigidaire part
By: Frigidaire
Part Number: 134371220
The Water Inlet Valve is an OEM part for Frigidaire washing machines. This part controls the flow of hot and cold water into the washer's tub, ensuring the correct temperature mix for various wash cycles. By opening and closing at the command of the washer's control system, it plays a pivotal role in the machine's ability to execute programmed wash cycles with precision, affecting everything from the initial fill to the rinse phases.
Causes for the replacement of the water inlet valve can range from mineral deposits and sediment build-up, which can obstruct the valve's flow, to mechanical wear and electrical failures affecting the valve's operation.
Symptoms of a malfunctioning Water Inlet Valve include:
- The washer not filling with water
- Water entering the machine slowly
- The washer filling with the wrong water temperature
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
The mixing valve that the water hoses attach to had frozen and broken. John M. • Commerce , TX • April 05, 2014
It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish.
Read more
More
$54.26
- Compare At:
-
$70.53
- You Save:
-
$16.27
Genuine Whirlpool part
By: Whirlpool
Part Number: W10853723
The Water Inlet Valve is an OEM part for Whirlpool washing machines. It controls the flow of water into the washer, ensuring the right amount of water enters the tub for each cycle. This valve connects to the water supply and is activated by the washing machine's control board to allow water to flow in and out as needed.
Over time, the water inlet valve can become faulty due to mineral deposits, wear and tear from constant use, or damage to the valve components. If the valve fails, it can cause issues with water flow, affecting the washing machine's performance.
Symptoms of a bad Water Inlet Valve include:
- No water entering the washer
- Slow filling or no water flow
- Washer not filling to the proper level
- Washer overflowing
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Water puddle on floor at front left corner; glass lid dripping water on soap dispenser from splashing and leaking down side panel onto floor Ronnie M. • Phoenix , AZ • June 25, 2019
As a Mechanic, I did the common sense approach:
INITIAL OBSERVATIONS & CHECKS:
- Unplug Machine & check inlet water hose connections for leaks and signs of hose failure;
- Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows...
- Inspect...
Read more
More
$93.95
- Compare At:
-
$110.86
- You Save:
-
$16.91
Genuine Speedqueen part
By: Speedqueen
Part Number: 205765
This dual water inlet valve kit controls the hot and cold water entering select top-load washers. Replacing a weak or leaking valve restores proper fill performance and helps prevent slow fills, wrong temperatures, and unwanted drips.
- Regulates hot and cold water flow into the tub during fill cycles
- Integrated inlet screens help trap debris from the water supply
- Failure can cause no fill, slow fill, incorrect temperature, continuous filling, or water seeping into the tub when off
What's included: One dual water inlet valve assembly (120V).
- Disconnect power and turn off both water supplies before servicing
- Place towels and a container to catch residual water; relieve pressure at the hoses
- Note and transfer hose and wire connections one-for-one to the new valve
- Restore water and power, run a test fill, and check for leaks
Do-It-Yourself Stories from Customers like You
Intermittent issues with the cold water fill Urrvano G. • Rochester , MN • January 03, 2026
I replaced both the solenoid (part of the inlet valve kit) and the pressure sensor. Online research suggested my intermittent issue with the cold water fill being just a trickle and then causing an error was likely due to one or both of those two parts failing. Since they are in the same spot it was suggested (and I agree) that it is best to replace both at the same time. The hardest and most frustrating part was getting the bracket back on with the two bottom tabs being in place. It took...
Read more
More
$36.63
- Compare At:
-
$40.70
- You Save:
-
$4.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 205613
The Water Inlet Valve is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer tub, ensuring the proper water level and supply for each wash cycle.
Causes of a bad water inlet valve can include sediment buildup or obstructions, electrical malfunctions, or normal wear and tear over time, leading to valve failure or improper operation.
Symptoms of a faulty water inlet valve include:
- The washer not filling with water or filling slowly
- Incorrect or inconsistent water levels during wash cycles
- Water leaks around the valve or inlet area
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
1 water leaking on the floor at left side and 2 occasionally tub filling a number of inches when sitting Kenneth S. • San Carlos , CA • April 15, 2016
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure...
Read more
More
$79.95
- Compare At:
-
$95.14
- You Save:
-
$15.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8540751
The Water Inlet Valve is an OEM part for Whirlpool washing machines. It controls the flow of water into the washer during the fill cycles, ensuring that the correct amount of water enters the tub for washing and rinsing. This valve is crucial for the proper functioning of the washing machine, as it regulates the water temperature and flow.
Causes of a bad water inlet valve can include mineral deposits from hard water, wear and tear over time, or electrical malfunctions. These issues can cause the valve to either not open or close properly, leading to water flow problems.
Symptoms of a bad Water Inlet Valve include:
- The washer not filling with water
- Slow fill cycles
- Water leaking from the valve
- Incorrect water temperature during cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Whirlpool duet showing an f20 code Cheryl T. • Chino Hills , CA • January 28, 2017
The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads.
Read more
More
$50.31
- Compare At:
-
$67.68
- You Save:
-
$17.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W11210463
The Water Inlet Valve is an OEM part for Whirlpool washing machines. It controls the flow of water into the washing machine during the wash and rinse cycles. This valve ensures that the correct amount of water is delivered to the tub, enabling optimal washing performance and efficiency.
You should replace the water inlet valve if it becomes faulty or damaged. Common causes of a bad water inlet valve can include mineral deposits or debris clogging the valve, wear and tear from regular use, or electrical issues affecting the valve's operation. A malfunctioning valve can lead to improper water levels and poor washing results.
Symptoms of a bad water inlet valve include:
- Washing machine not filling with water
- Washer filling slowly or with low water pressure
- Leaks around the valve area
- Washer not advancing to the wash or rinse cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
No cold water, down to a trickle no code screens clean good pressure from hose faulty valve Terry P. • Freedom , PA • October 26, 2020
Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer.
Read more
More
$89.95
- Compare At:
-
$107.04
- You Save:
-
$17.09
Genuine Bosch part
By: Bosch
Part Number: 00422244
The Cold Water Inlet Valve is an OEM part for Bosch washing machines. It is designed to regulate the flow of cold water into the washing machine during the wash cycle. This valve operates based on signals from the washing machine's control board, ensuring the right amount of cold water is provided.
Causes of a faulty cold water inlet valve can include wear and tear over time, clogs or blockages in the valve, electrical issues, or valve failure.
Symptoms of a bad cold water inlet valve may include:
- Insufficient or no cold water flow into the washing machine
- Leaking or dripping water from the valve during the wash cycle
- Inconsistent or inadequate water supply for washing clothes
- Error codes related to water supply or filling
This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
Note: For the Hot Water Valve, order part number 00422245.
Do-It-Yourself Stories from Customers like You
Leaking washer (bosch 10 years old) and found out that was a cracked cold water inlet valve once i investigated where leak was coming from F Gloria S. • Southampton , NY • May 30, 2015
First - shut off water valves & unplugged electric.
Second - opened up back of washer & removed top part as well.
Third - turned hot & cold water back on one at a time to see where the leak was coming from...lucky for me it was the inlet valve which was right there at the back of washer. Turned water off again.
Fourth - located part on internet - and found you & ordered part but not before I went to Lowe's and called local appliance part stores to see if I could find...did not...came home and...
Read more
More
$59.95
- Compare At:
-
$71.94
- You Save:
-
$11.99
Genuine Ge part
By: Ge
Part Number: WH13X10023
The Water Inlet Valve is an OEM part for GE washing machines. It controls the flow of water into the washer during the fill cycles. The valve opens and closes to allow the correct amount of water to enter the machine based on the selected wash cycle and settings.
You should replace this water inlet valve if it becomes defective. A bad water inlet valve can cause several issues such as improper water levels, slow filling, or no water entering the washer at all. These problems can be due to sediment build-up, electrical faults, or mechanical wear.
Symptoms of a bad water inlet valve include:
- Washer not filling with water
- Slow filling or low water pressure
- Leaking or dripping water from the valve area
- Incorrect water levels in the drum
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Error 22 error 23 on ge frontload washer Stephanie Y. • Indio , CA • June 13, 2014
I reseached these error codes and compared them to others problems. After deciding that I was gonna order the part and fix it myself I was at ease to find out it took 10min to fix! And it actually worked! The washer was pausing during cycles, cloths were soaking wet, spin cycle only worked on drain and spin at the end of the Ioad (it would spin slowly otherwise), soap dispenser still had the soap in it or it would be filled with water after the cycle was over. I watched videos on how to change...
Read more
More
$99.32
- Compare At:
-
$117.20
- You Save:
-
$17.88
Genuine Ge part
By: Ge
Part Number: WH13X23974
The Triple Water Valve is an OEM part specifically designed for GE washing machines. It precisely controls the flow of water into three separate circuits to fill the tub, dispense detergent and drain dirty water.
Symptoms of a faulty valve include:
- Inability to fully or properly fill the washer
- Inadequate rinsing or failure to drain fully
- Uneven or inconsistent water levels
- Leaks or water left in the tub after cycles
Causes can be mineral buildup affecting water flow, internal component wear over time, or damage that disrupts valve operation.
This OEM GE replacement part is also compatible with Hotpoint, RCA and some Kenmore models as well.
Do-It-Yourself Stories from Customers like You
The original valve for the cold water wasn't shutting off completely and would leak quite a bit after the wash cyle and again after the rinse cycle Betty B. • Vernon , NJ • May 31, 2014
My husband fixed it, he took out the leaky valve and replaced it with the new valve, which we received in the mail from your company, which was only a short time after we ordered it. Thank you for being so prompt. Our washer is only a little over 2 years old and upon looking online, we found out this model has since been discontinued due to problems. The parts are no longer available from GE, so we were thrilled to find your company online which carried the part. It saved us a lot of money...
Read more
More
$41.55
- Compare At:
-
$49.86
- You Save:
-
$8.31
Genuine Whirlpool part
By: Whirlpool
Part Number: W11688995
The Water Inlet Valve is an OEM part for Whirlpool washing machines. This part controls the flow of water into the washer during the filling cycles. This valve ensures that the correct amount of water is delivered to the tub, allowing for optimal washing performance.
Causes of a bad water inlet valve can include mineral buildup, electrical issues, or wear and tear from regular use.
Symptoms of a bad water inlet valve include:
- The washer not filling with water
- Slow filling or incorrect water temperature
- Water leaking from the valve
- The washer filling continuously or not at all
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Loud chugging noises when the washer filled followed by an occasional low flow error code Donn O. • Phoenix , AZ • November 15, 2020
Replaced both hot and cold water inlet valves. Works like a charm, issue resolved.
Read more
More
$68.95
- Compare At:
-
$81.36
- You Save:
-
$12.41