205C-2981-Pod-112 Parts

The Power Cord is an OEM part for Frigidaire refrigerators. It transmits electrical current from the wall outlet directly to the internal refrigerator components, allowing them to operate properly. As the critical link supplying energy, this power cord plays an essential role in refrigerator performance.

Causes can involve normal wear over many years, accidental punctures, harsh chemicals, or excessive bending/pulling that strains and weakens internal wiring. Rodent damage is another potential issue.

Symptoms of a bad power cord include:

• The refrigerator not powering on when plugged in
• Flickering lights or intermittent operation
• Warm temperatures inside the fridge compartment
• Evidence of cord damage like cracks, blisters, or exposed wires

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Temperature Switch is an OEM replacement part for Whirlpool washing machines. This switch monitors incoming water temperatures to ensure they fall within the thresholds required for selecting dependent wash cycles. It plays an important safety function by preventing the activation of vulnerable "hot" cycles if water is too cool. 

Causes of a bad water temperature switch can include failures from repetitive heating/cooling cycles, mineral deposits obstructing sensors over time, or defective temperature sensing mechanisms.

Symptoms of a bad water temperature switch include:

• Inability to select high-temperature cycles  
• Fault codes related to water supply temperatures
• Potential improper washing if the temperature reading is inaccurate

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

These lid bumpers are sold individually.

This small clip secures the washer's agitator assembly. It holds components in place so the agitator engages the drive properly, helping restore steady agitation and preventing looseness or rattling during the wash cycle.

• Retains agitator components in their correct position for consistent wash action
• Helps prevent the agitator or upper auger from lifting off or wobbling
• Can address symptoms like weak/intermittent agitation, a loose agitator, or clicking from the center post
• Commonly replaced during agitator service to ensure a tight, reliable fit

• Disconnect power and turn off water before servicing
• Remove the dispenser and agitator cap; take out the center fastener/retainer as your model requires
• Lift the agitator to access the clip; note its orientation and use needle-nose pliers to remove and seat the new clip fully
• Reassemble, ensure the cap is secure, and test for proper agitation

Used to lock washer cabinet to rear wall of washer.

The Infinite Knob is an OEM part for GE ranges and cooktops. This part provides control over the heating elements. This knob allows users to adjust the temperature setting of their range or cooktop, ensuring accurate cooking temperatures for a variety of dishes. 

Causes for issues with the Infinite Knob often involve regular wear and tear, accidental damage from cleaning or use, or degradation of the material over time.

Symptoms of a malfunctioning Infinite Knob include:

• Difficulty in adjusting the temperature setting
• The knob slipping or failing to engage with the control shaft
• Visible wear or damage to the knob

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.

Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.

Symptoms of a bad spacer include:

• Misalignment of components
• Unusual noises during operation
• Difficulty in assembling or disassembling parts
• Reduced efficiency of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Sold individually, four are needed to replace all parts. Screw part number WP3390631.

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

Nylon

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

Rubber grommet for motor mount stud.

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

10 - 16 x 1/2

This selector switch lets you choose the oven's operating mode from the front control knob. Replacing a worn switch restores reliable mode selection so power is routed correctly to the cooking function you select. What it does

• Connects the control knob to the proper circuit to engage the selected oven function
• Restores consistent operation when the oven won't start or won't stay in certain modes
• Addresses issues like only one function working or intermittent mode changes
• Helps when the knob turns but doesn't change functions or the selector shaft feels loose

• 1 selector switch

• Disconnect power at the breaker or fuse panel before servicing; allow the appliance to cool
• Pull off the control knob and remove the control panel/backguard to access the switch
• Move wires to the new switch one at a time, matching positions (take a photo or label leads)
• Secure the switch, reassemble, reinstall the knob, and test each oven function