66513733K601 Kenmore Parts

• Will not fill with water

Cycle would complete but dishes weren't clean (not even really wet) and soap wasn't dissolving. Could hear fill at start but maybe not spraying or filling again in cycle. Thought it was the control board, but actually this was not the error. Replaced the control board and same problem arose, only new control board version actually stopped cycle with message that dishwasher couldn't fill. Looking underneath the pump had somehow become dislodged from the bottom of dishwasher and was laying on... Read more

• Not cleaning dishes properly

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

Replaced the upper spray arm seal Read more

First unplug or turn off the electrical breaker to the dishwasher. Then I removed the phillips head screws holding the inner door to the outer door panel. I then removed the hex head screws holding the dispenser assembly. The electrical connection needs to be disconnected and then reverse the procedure to install the new dispenser. Restore power to the dishwasher and your done. Read more

Order parts and replace. When removing attachments, do them one at a time and install them on new rack as you go. Watch for the small release tabs on the attachments (baskets, rollers and tine holders), "gently" put pressure to release; remember these units have been in hot water and they are brittle. Read more

Ordered new insulation from AppliancePartsPros. It was delivered quickly and easy to install. Read more

Replaced It With New One Read more

Touch up paint Read more

My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

This was a difficult problem to diagnose. Because the machine would start the wash cycle then shut down after a few minutes of running, it appeared that the cause might be a bad thermostat or heating element, but all checked out ok. That led me to believe that the control panel may be the culprit but it also appeared to be working correctly when I ran the diagnostics program. A visual examination of the components found that the door switch electrical connections looked discolored, so I removed... Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more

The odor in the dishwasher was due to scum buildup in the walls, the racks, and in the lower part of the drain below the lower rotating arm. One of the valves in the vertical tube was stuck in the open position; since the valves cannot be replaced, the entire tube needed replacement. The check valve probably needed no replacement, but once I opened the bottom part, I decided to replace it anyway. I used this Youtube video to replace the tube, open and clean the drainage part of the washer: ... Read more