Ge Gss22jfmdww Refrigerator Parts

Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more

The new slides fit perfectly. One thing to mention is that the slide rails come with the slide bearings so you do not need to buy those separate. When I called I was told I needed the bearings so I bought 3 assuming I would be able to salvage the others. Turns out I did not need them. Read more

Changed fan motor, rubber grommets, and dust cover. It sounded like the vibrating sound was being caused by the motor. But, come to find out I had a chipped blade on one of the fan blades. So make sure and check the fan blade first. Thanks Appliance Parts Pros everything for just as it should. Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

Pop out the old switches with a putty knife pressing down on the tab, grabbed with pliers to pull out, disconnect the wires and connect new switches, pressing back in place. Read more

I looked for a site that sold replacement parts for my make of GE refrigerator. I found AppliancePartsPros, and was very surprised at how organized it was. By entering the model number of my refrigerator, I was shown a set of (approximately) 8 general parts diagrams for my refrigerator. I chose the ice making/dispensing diagram. I matched the part that shattered (from use) to what was on the diagram. What I didn't know was how to install the part. I saw references by other customer comments to... Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

I replaced the supply line to the fridge - no change in taste. I replaced the MWF manifold and tubes, the water inlet valve and the water storage line. That did it, good tasting water again! The ice still has a bad taste, so I'll replace the supply tube from the valve to the ice maker. Overall, replacing these parts was easy and the videos from Appliance Parts Pros helped. Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

This was a two and half year issue as different things failed at different times. I would get one part, then another would fail. Ultimately, I got to a point where what failed, I hadn't been ordered the part yet. The seal on the freezer door took three bathing's before it plumped up and un-creased. The directions on the box it is shipped in said to heat the seal up in hot water then cool it down with tap water. I didn't need to do that. It took a lot of massaging of the seal, but... Read more

Check compressor with my Hotwire kit I made when I worked for GE. When removing the compressor relay it broke in pieces. Ordered and replaced new relay, overload & run capacitor. Still did not work. Check if there’s power to compressor and found no voltage. Took control board out and found a component burnt. Ordered and replaced control board. Everything is back to normal. Love your service. Parts was supposed to come in 3-5 days but came next day instead. I am very very impressed and grateful.... Read more

Replaced the stripper and fill cup - turns out that the fill cup came with the locking tab broken off. The stripper had a missing paddle, and ice cubes would jam and shut down the ice maker periodically. Let the ice maker warm up after you remove it so the plastic is not so brittle. You have to pry the old stripper out. Make sure the new one locks all across the front. My refrigerator has the ice maker mount toe the side instead of from the hangers in back. I wasn't sure how to remove it,... Read more

New cond fan & new evap fan & new defrost heater unit Read more

When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more

Had some confusion of what part I needed, needed the one with the motor and thermostat. Fortunately, I've been fixing wiring for many years, I simply cut the new motor out of the harness, and used that nice glue-inside-heat-shrink tubing to seal the soldered 'Western Union' style splices. New light socket and lamps fit fine, worked fine, new motor is fine, problem resolved. FYI: Look closely at the wiring in you unit, there are two wire harnesses, one feeds the light, the other feeds the motor... Read more

The hinge broke on the ice dispenser funnel and housing. I took them off and replace them, putting the old switches and bulb in the new housing. It took some time to put the return spring back because it does not appear in the assembly diagram. Once working, it secures to the door with 4 screws, and worked as it should. The support slide inside the freezer is held with two 1/4 in screws that were taken off with a nut driver. the rear screw is hard to get at. The new bracket just screws on, and... Read more