Gld4458r00c5 Parts

The Drain Hose Kit is an OEM replacement part for GE built-in dishwasher models. It includes flexible tubing and attachments responsible for draining used water from the wash chamber via the internal pump outlet.

Symptoms of a bad drain hose include:

• Puddles or standing water left inside after cycles complete
• Slower overall wash and dry times from impaired drainage
• Nosier pump operation potentially from hose blockages

Causes of failure can stem from cracking over extended usage years, or mineral buildup restricting flow. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore refrigerators. 

The Lower Door Seal is an OEM replacement part for GE dishwashers. Located along the bottom edge of the dishwasher door, this rubber seal creates an airtight barrier when closed to prevent leaks during wash cycles.

Causes of a faulty lower door seal often involve normal deterioration of rubber over extended use, allowing cracks to form and reducing its flexibility.

Symptoms of an inadequate lower door seal include:

• Puddles or water leaks beneath the appliance
• Mineral deposits left behind after drying cycles
• Inability to maintain optimal interior humidity
• Gaps appearing along the bottom door perimeter

This OEM GE replacement seal is also compatible with Hotpoint, RCA, and some Kenmore models.

The Pump and Motor Assembly is an OEM replacement part for GE dishwashers. It works to circulate water throughout wash and rinse cycles. The motor spins the integrated pump impeller to draw fresh water into the dishwasher and drain used water.

Causes of a bad pump and motor assembly can include mineral buildup on pump parts inhibiting water flow, worn motor windings reducing efficiency, or damage from freezing temperatures.

Symptoms of a bad pump and motor assembly include:

• Inability to fill or drain water from the dishwasher
• Abnormal noises coming from the motor area
• Leaks or water not circulating properly

This OEM part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Circulation Pump Impeller Kit is an OEM replacement part for GE dishwashers. This kit includes the necessary impeller components responsible for circulating water throughout dishwashing cycles. 

Causes of a bad circulation pump assembly include normal wear from continuous pump operation, along with mineral or debris buildup that can affect water flow.

Symptoms include:

• Inadequate or lack of water circulation within cycles
• Dirty dishes even after full cycles due to insufficient cleaning 

This OEM GE part is compatible with some Hotpoint, RCA, and select Kenmore models. 

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Plunger Spring is an OEM part for GE dishwashers. This spring is part of the door latch mechanism, helping to ensure that the dishwasher door latches and unlatches properly. It provides the necessary tension to keep the door securely closed during operation, preventing leaks and ensuring the appliance runs efficiently.

Causes of a bad plunger spring can include wear and tear from regular use, corrosion due to exposure to moisture, or physical damage such as bending or breaking. Keeping the plunger spring in good condition is crucial for the proper functioning of the door latch.

Symptoms of a bad plunger spring include:

• Difficulty in latching or unlatching the dishwasher door
• The door not staying securely closed during operation
• Water leaking from the door
• The door feeling loose or not closing properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Specs: B-16 HXW 1/2 SS

This replacement part is an upper rack slide, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This upper rack slide is an important part of many appliances. This particular one is typically found in dishwashers and helps guide the upper rack in and out. This allows the user to have easy access to the rack in order to place and remove dishes before and after the cleaning process. A new upper slide rack might be needed if the current ones are broken or damaged in any way. It is possible that these slides become stripped over many years of use and need to be replaced. If the upper rack is tilted or not sturdy while being slid back inside the main tub, the upper rack slide might be the problem. Be sure the dishwasher is completely empty prior to replacing this part. This is a genuine OEM part and is sourced directly from the manufacturer. This upper arm rack slide is sold individually.

This middle spray arm hub secures the dishwasher's middle spray arm to the feed tube and lets it spin smoothly, helping deliver even spray coverage so dishes in the upper rack area get properly cleaned.

• Connects the middle spray arm to the water feed/manifold and serves as its rotating center
• Keeps the arm aligned so jets can distribute water evenly
• Wear or cracks can cause the arm to wobble, fall off, bind, or stop spinning
• Symptoms include poor cleaning on the upper rack and unusual noise from the arm area

• Disconnect power and water supply before servicing
• Remove the middle spray arm per your model's design and note its orientation
• Transfer and reuse any original screws, clips, or washers; install the new hub without overtightening
• Spin the arm by hand to ensure free movement before running a brief test cycle

Lower dishwasher rack roller axle only. Color: White. Measures about 1 inch wide by 1 inch high by a 1/2 inch deep. For Gray color order part number WD35X21041.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

Includes screws.

This inlet sump is the lower-tub water intake for the circulation system. It channels wash water to the pump and seals the connection, helping prevent leaks and restoring proper wash performance when the original is cracked, warped, or clogged.

• Directs wash water from the tub into the circulation pump
• Maintains a watertight seal at the pump/sump opening
• Common failure symptoms: water leaking from beneath the unit, poor cleaning results, unusual noise from the pump area
• Visual clues: cracks, deformation, or mineral buildup on the sump inlet

• Disconnect power and shut off the water supply before servicing
• Access is typically from inside the tub and/or the bottom; remove lower rack, spray arm, and sump cover as needed
• Transfer existing clamps/seals and inspect gaskets; replace any worn seals for a proper fit
• Seat the sump fully, secure connections, then run a short cycle to check for leaks

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 10-32 GXTT FLP.595 S