Gss25tgmacc Ge Refrigerator Parts

• Leaking

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

Replaced Read more

Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more

This fridge has had a problem of ice building up around evaporator coil in fresh food side. Wife (she HATES this thing) says it's done this from day one; 10 years. GE guy says all these models do this and there's no fix for it, so we have clean out the ice periodically... Like the 1940s pre auto defrost. Now with the issue of FF side temp too highi assumed the ice had built up around FF evaporator coil preventing proper cooling, but AppliancePartsPros.com suggested the FF temp thermistor may... Read more

Ordered replacement seals for both freezer and refrigerator sides. Followed directions that I had found on YouTube. The installation in a nut shell is warm the seals in a bathtub with very hot water for at least 2-3hrs then place the seals. Then warm the seals with a hair dryer as needed. After getting the seals out of the hot bath the installation took all of 20-25 minutes for both seals. Read more

When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more

Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both Read more

Used the schematic provided to select the parts needing replacement and placed the order. Parts arrived and swapping new for old was simple. For the most part it was a matter of taking out the old and putting in the new. There were a few screws with wheels to replace but that was easy as well. Before purchase I searched several different sites and found all the parts needed. I compared prices of each item as well as shipping cost. Prices for each item were nearly identical between sites... Read more

The hinge broke on the ice dispenser funnel and housing. I took them off and replace them, putting the old switches and bulb in the new housing. It took some time to put the return spring back because it does not appear in the assembly diagram. Once working, it secures to the door with 4 screws, and worked as it should. The support slide inside the freezer is held with two 1/4 in screws that were taken off with a nut driver. the rear screw is hard to get at. The new bracket just screws on, and... Read more

Watched short You Tube repair video. I saved at least on a $100 GE service call. The electronic ID assembly was priced much less than quote on GE.com! Read more

I thought I would have to buy a whole new refrigerator, but I looked online at AppliancePartsPros.com. I put in my model number of the refrigerator and the whole diagram came up. This made it so much easier to choose the parts I need to replace. I received the order in a few days so I was able to fix the problem quickly. The assembly was easy and the video helped also. Read more

I watched the videos and ordered the parts to fix the problem. Then I installed them and so far everything seems to work ok. It's only been a few days so we'll see if I got it right. Read more

Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more

I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more

Bought a new panel and installed it. It was simple 3 plugs and done. Read more

I bought two parts. The dispenser housing shield and the funnel ice dispenser. I watched the short video on how to put it back together and I was done in just a matter of minutes. The video was such a big help. I forgot how the spring went on and was able to watch the video and put it back together in just a matter of minutes. I know I must have saved a couple of hundred dollars on a service call. Read more