Mdbh945aww2 Maytag Dishwasher Parts

• Will not drain

I ordered the part from you which amazingly showed up less than 20 hours after I ordered it. I then watched a video you produced about replacing the part. Between those two things I had my dishwasher up and running withing 36 hours of talking to your rep. Read more

New spring and cable Read more

Bottom replacement rack is a complete unit. Simply slid the old, rusted one out and slid the new one in. Read more

• Not cleaning dishes properly

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

Spun each of the three wash arms by hand. All could be made to touch/scrape but the top one was super wabbly. Ordered both the arm and clip. Repair took less than a minute. Used a screwdriver to pry loose one side of the old clip to remove. Aligned the new parts and easily snapped into place. Read more

I wasn't sure if the problem was going to be the key pad or the electronic control board, so I ordered both parts. The key pad fixed the problem, so I will be returning the control board. I had a bit of concern because I wasn't sure how the ribbon cable connector worked, but it turned out to be pretty easy. You slide the top part of the connector back along the axis of the ribbon cable to take it apart. Insert the ribbon cable from the new key pad and just snap the connector back together. No... Read more

• Will not fill with water

I replaced the float switch. It was an easy enough repair. I didn't have to remove the dishwasher to do the work. The part is accessible from behind the front skirt.The only problem was there is not a lot of space to work in. Getting the fastener off and on requires a stubby nut driver. I used a flexible extension instead. I had to feel for the nut as the bottom of the door blocked my view. A ten minute job and the dishwasher is back in service (for half the cost of my local parts place) While... Read more

Replaced pump and filter. Read more

• Will not dispense detergent

Ordered the part. Arrived the next day. Took the eleven screws off the door exposing the back of the Soap/Rinse Aid dispenser. Six screws hold it on the inside of the door. Popped off easily. There is a plug that runs from the timer to the dispenser…it's a pain to get off. Use a flat head screw driver. Screwed the new unit in place. Plugged it in. Put the door back together. I accidentally caught the door catch in the door and screwed it together seizing it...so I had to take the top screws off... Read more

Replaced dishwasher door latch assembly. Read more

Tested starter capacitor at 2.16µF. pic: http://s29.postimg.org/e05fufxdz/IMG_20150716_140312.jpg It should be 15µF. pic: http://s29.postimg.org/x3yrasa87/IMG_20150718_112327.jpg Contrary to service manual, capacitor is not accessible behind the toe/kick-plate; it is underneath but all the way towards the rear. To get to it, the dishwasher has to be removed and positioned face-down (drain first, use towels/drop-cloth). Read more

Ordered a new cover and installed it with no problems Read more

I bought the dishwasher used and the control panel never fully worked. The countdown timer was non-functional, many of the buttons were unresponsive, and "start" needed to be pressed multiple times before the dishwasher would turn on. After a few months, none of the lights worked, and all the buttons stopped responding. I first replaced the handle, since it was also broken (the door was difficult to open) and there was a chance it wasn't registering the door as fully closed. The new handle... Read more