Mgr6775 Mgr6875 Parts

Had to drill out the portion of the old foot that was still in the grate. Cleaned out the opening. Popped in the new one and voilà- all fixed. I ordered 8 of the feet as I see this eventually happening to all of them. Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

Removed side moldings top molding and glass, removed broken handle. Reinstalled new handle, all modings and glass. Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

• Door won't open or close

The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

Ordered a new one and replaced it, Read more

No work needed. Read more

I ordered a new door glass from appliancepartspro.com it came within two days, but I forgot to order the 8 pieces of foam tape, assuming it would also be included in with the order, it wasn't, so after waiting for that to arrive, it was fairly easy, job after watching the video. However, the video doesn't tell you the painted side goes on the inside, or that the single sided foam tape goes on the top, and the double sided foam tape goes on the sides, I figured that out from the diagram on my... Read more