Sdg-4606Aww Parts

The Drum Roller Axle is an OEM replacement part for Whirlpool dryers. It is the component that attaches to the rear panel and supports the dryer drum rollers.

Causes of a bad drum roller axle can include wear from years of operation, potentially leading to bending or wobbling that disturbs smooth drum spinning. Bearing seals may also deteriorate through continuous motion and heat exposure.

Symptoms of a bad Drum Roller Axle include:

• Vibrations or imbalanced drum rotations sensed during drying
• Premature failure of other drum or suspension components
• Reduced efficiency as uneven tumbling hinders fabric agitation
• Noises and rattling sounds from within the dryer cylinder area

This OEM Whirlpool part is also compatible with Maytag, Jenn-Air, Amana, and select Kenmore models

The Retaining Ring is an OEM replacement part for Whirlpool dryers and washing machines. This retaining ring holds the rear wheels on the axels of the washer or dryer. 

Symptoms of a bad retaining ring can include wear and tear over time, damage due to accident or impact, or corrosion affecting the structural integrity.

Causes of a bad retaining ring dryer include:

• Excessive vibration or movement of the drum during operation 
• Noise or banging sounds from loose components   
• Deformation or cracking of the retaining ring itself
• The dryer door not closing properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drum Glide Bracket is an OEM replacement part for Whirlpool dryers. This bracket serves to securely support the rotating drum assembly within the dryer cabinet while allowing it free movement during operation. 

Symptoms of a bad drum glide bracket include:

• Excessive vibration or noise from the drum area
• Difficulty turning or spinning of the drum 
• Scratching or damage to the dryer cabinet walls caused by drum contact
• Misalignment of the drum which can affect drying performance

Causes of a bad bracket can be extensive use over time which leads to wear of the mounting points, or accidental damage from overloading or abuse.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions. 

Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts. 

Symptoms of a bad light bulb include:

• The dispenser area not lighting up when activated
• Flickering or dim lighting
• The bulb failing to turn on consistently

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.

• Controls the heating circuit to maintain target drying temperatures
• Provides temperature feedback for accurate auto-dry operation
• Common symptoms: long dry times, very hot drum/cabinet or scorching odors, auto-dry not advancing correctly, or no heat if the thermostat fails open
• Typically mounted on the blower housing to sense exhaust air temperature

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat (commonly on the blower housing); remove the necessary panel(s)
• Transfer wires one at a time to the new thermostat and mount it flat against the housing
• Reassemble, verify clear venting/airflow, and run a test cycle

This factory fastener secures appliance components such as panels, brackets, and trim. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and helps keep assemblies aligned for reliable performance.

• Fastens appliance parts to maintain structural integrity and alignment
• Helps address symptoms like loose or vibrating panels, gaps, or hardware that won't stay tight
• Replaces lost, damaged, or corroded fasteners during repairs or reassembly
• OEM-matched thread and fit for the specified location

• Disconnect power; shut off gas or water supplies before servicing
• Replace one screw at a time to preserve alignment of parts
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver size/type specified for your model

10 - 16 x 1/2

This cycling thermostat regulates your dryer's internal air temperature by switching the heat source on and off, helping prevent overheating and keeping drying performance consistent. Replace it if temperatures are erratic, items run too hot, or dry times increase. What it does:

• Monitors drum air temperature and opens/closes to control the heater
• Maintains stable temperatures across fabric/temperature settings
• Failure symptoms include no or low heat, overheating/scorch smells, long dry times, or inconsistent cycling
• Helps protect against damage from excessive heat when functioning correctly

• 1 cycling thermostat

• Disconnect power; if it's a gas dryer, also shut off the gas supply
• Allow the unit to cool; access the thermostat (typically on an internal air duct or blower housing); note wire positions
• Transfer wires to the new thermostat one at a time; mount flush against the metal surface; do not overtighten
• After installation, clean lint passages and ensure proper airflow and temperature control

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This kit replaces a temperature-control thermostat and its mounting plate in select dryers. It helps restore accurate heat regulation and consistent cycling, protecting against overheating and poor drying results when the original thermostat or bracket has failed.

• Senses exhaust air temperature and opens/closes contacts to control the heater
• Helps maintain consistent drying temperatures and safe operation
• Failure symptoms include no heat, insufficient heat, overheating, or erratic cycling
• Mounts with the included plate to ensure proper positioning of the thermostat

• Disconnect power before servicing; for gas units, also shut off gas supply
• Access the thermostat location (typically on the blower/exhaust housing); note wire positions and transfer one at a time
• Attach the thermostat to the plate and secure the assembly using existing hardware if new fasteners are not provided
• After reassembly, verify proper airflow and clean the lint path and venting

For complete assembly for easier installation order WP37001287

This cycle selector knob is used on some Maytag washers and dryers. This is not the timer knob. Color: stainless steel. Measures about 2 inches in diameter where the handle extends.

Screw: 8-16 x 3/8 inch.

This LP gas conversion kit lets compatible gas ranges be converted from natural gas to LP (propane), supplying the correct orifices and settings so burners run safely and produce expected heat on LP fuel. What it does:

• Replaces factory burner orifices and related fittings to match LP fuel pressure and flow.
• Helps restore proper flame size and burner performance after switching from natural gas to propane.
• Addresses symptoms such as weak or yellow flames, uneven heating, or reduced burner output after fuel change.
• Intended for use only on ranges specified by the manufacturer for this conversion kit.

• Shut off the gas supply and disconnect power before beginning work.
• After installation, perform a leak test and verify correct flame characteristics on all burners.
• Keep original parts and the instructions for future reference and warranty requirements.

This electronic timer controls dryer cycle selection and timing, restoring proper cycle advancement and user control. It replaces a failed or unresponsive timer to help your dryer start and run the selected cycles reliably. What it does

• Advances dryer cycles and manages timed and automatic cycle control.
• Provides the user interface signals for start/stop and cycle selection.
• Can correct symptoms like a dryer that won't advance through cycles, won't start reliably, or has an unresponsive cycle selector.
• Works with the dryer's control circuitry to coordinate motor and heater operation during selected cycles.

• Disconnect power to the dryer before any service to avoid shock risk.
• Verify wire connections and match terminal locations to the wiring diagram before removal.
• Handle the control carefully; avoid bending terminals or contaminants on connectors.