Wm3987hw Lg Parts

The Hose is an OEM part for LG washing machines. This component is crucial for the proper flow of water into and out of the washing machine, ensuring efficient washing and rinsing cycles. The hose is designed to withstand high water pressure and regular use.

Causes of a bad hose can include wear and tear over time, exposure to harsh water conditions, or accidental damage such as kinks or punctures. Ensuring the hose is in good condition is essential to prevent leaks and maintain optimal water flow.

Symptoms of a bad hose include:

• Water leaks around the hose connections
• Reduced water flow into or out of the washing machine
• Visible cracks, bulges, or kinks in the hose

This OEM LG part is also compatible with Sears/Kenmore.

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

This water inlet valve assembly regulates the flow of water into your washer during the fill and rinse cycle. Replacing a sticking or leaking valve restores proper filling and helps prevent drips when the washer is off. What it does:

• Controls and directs incoming water into the washer as signaled by the control
• Opens and closes to reach target fill levels, then shuts off water flow
• Symptoms include: washer won't fill or fills very slowly
• Symptoms include: water keeps running or drips into the tub when the washer is off
• Symptoms include: leaks from the valve body or hose connections at the back of the washer

• One water inlet valve assembly

• Unplug the washer and shut off both water supplies before starting
• Keep a towel or tray handy and relieve line pressure before removing hoses
• Move hoses and wire connectors to the new valve one at a time to avoid mix-ups
• Turn water back on, check all connections for leaks, then run a test fill

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

This replacement bolt secures the drum spider within the washer tub assembly. Replacing worn or missing hardware helps keep the basket properly mounted to reduce wobble, vibration, and noise during spin.

• Fastens the spider to the inner wash basket
• Maintains proper alignment and balance of the basket during spin
• Use when original bolts are rusted, stripped, loose, or missing
• Symptoms include rattling, thumping, off-balance errors, or visible basket wobble

• Unplug the appliance; shut off water and remove hoses if access requires moving the unit
• Access typically requires panel removal to reach the inner basket and spider
• Replace any damaged bolts and tighten evenly in a crisscross pattern; do not overtighten
• Inspect the spider and basket for corrosion or cracks before reassembly

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This washer motor stator assembly is the stationary windings of the direct-drive motor. Replacing a weak or shorted stator restores smooth drum tumbling and strong, consistent spin performance so wash cycles complete properly.

• Creates the rotating magnetic field that drives the rotor and spins the inner basket
• Works with the rotor to provide torque for wash/tumble and high-speed spin
• Common symptoms: drum won't spin or tumble, stops under load, or motor hums without turning
• Burnt odor or visible heat damage on windings can indicate stator failure

• Disconnect power and turn off water; access the motor from the rear panel
• Remove the rotor center bolt and slide off the rotor; strong magnets—handle carefully
• Unbolt and remove the stator; transfer/reconnect the motor position (Hall) sensor and harness if present
• Tighten fasteners evenly; verify drum rotates freely by hand before restoring power

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

The Drawer Front Panel Assembly is the complete replacement front for a pull-out drawer. It restores a clean look and solid handle support so the drawer opens and closes smoothly and sits flush again. What it does:

• Attaches to the drawer frame to provide the finished outer front
• Supports handle mounting and helps keep the drawer aligned
• Common fix for a cracked or dented front, broken mounting tabs, or a loose/missing panel
• Can help resolve a drawer that won't close flush or feels wobbly

• 1 drawer front panel assembly

• Disconnect power before servicing; remove items from the drawer to reduce weight
• Remove the handle and mounting screws; support the panel as you lift it off the drawer
• Transfer any reusable hardware from the old panel; align the new panel and tighten fasteners evenly
• Test drawer operation and fit; adjust as needed per service information

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This inlet hose channels household water to the appliance's fill system. Replacing a worn or leaking hose restores proper water flow and helps protect floors and internal components from water damage.

• Directs water from the household supply to the unit's inlet/fill assembly
• Maintains a watertight path to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or mineral-fouled
• Common symptoms: leaks at fittings or beneath the unit, slow or no fill, intermittent filling, or water-related error messages

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure slowly
• Route the hose without kinks; ensure sealing surfaces and/or washers are clean and properly seated
• Secure connections per the OEM design (compression fitting or clamp); restore water and check carefully for leaks on the first run

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.