Valve Parts

• Leaking
• Not dispensing water

Installed a new water valve assembly and a new ice maker assembly. Read more

Replaced water valve and ice maker Read more

• overflowing

This was not my first rodeo have repaired our appliances and those of our daughters for years, have ordered parts from this site several times. We had a cold spell in Texas, as you may have heard. We weathered it okay but left the dishwasher closed on one of the colder nights, woke up to water on the floor in the kitchen. Turned off the supply line, shut off the dishwasher power, bailed out the bottom, and mopped up. Had a fair idea of what the cause was, checked a few websites, watched some... Read more

A bit of online research and some component testing narrowed my issue down to either a faulty ice maker or a bad supply valve. Appliance Parts Pros had both of these, at reasonable prices, so I purchased and replaced both items. I recommend watching online videos to get a sense of what to do, and how to go about doing it. The repairs were relatively easy, other than this being a bottom freezer model hence the ice maker was difficult to access: I removed the freezer door (four screws) to get... Read more

• Ice maker not making ice
• Leaking

Replaced inlet water valve Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered water inlet valve. Two screws to take out. Disconnect the hose. Disconnect the two wires. Put in the new valve. Reverse the procedure. Whole thing took about 10 minutes. Read more

I replaced both the solenoid (part of the inlet valve kit) and the pressure sensor. Online research suggested my intermittent issue with the cold water fill being just a trickle and then causing an error was likely due to one or both of those two parts failing. Since they are in the same spot it was suggested (and I agree) that it is best to replace both at the same time. The hardest and most frustrating part was getting the bracket back on with the two bottom tabs being in place. It took... Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more

1.) Located where the water leak was coming from in the refrigerator. 2.) Unplugged the refrigerator. 3.) Shut off the water supply to the refrigerator. 4.) Unscrewed the back cardboard panel. 5.) Unscrewed the Water Valve attached to the side of the refrigerator (one screw). 6.) Disconnected the three electrical plugs on the water valve. The plugs are different sizes so there is no need to worry about reconnecting incorrectly. 7.) Disconnected the two water lines by pushing down on... Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

I ordered a new solenoid valve set and watched the online video of the replacement process. So after emptying my freezer and fridge, removing the doors and freezer drawer, so I could mover the fridge out of its cove, I discovered after taking the panels off the rear, that my fridge is different than that shown in the video. I went back online and discovered in one of the exploded views of the cabinet there is a panel inside the refrigerator which can be removed after taking the shelves out of... Read more

• Will not fill with water
• Will not stop filling with water

The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads. Read more

Replaced icemaker Read more