Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces worn or leaking shock absorbers that cause excessive vibration and wobbling during spin cycles. Restores stability and smooth operation.
My washing machine was making a loud thumping sound and bouncing around a bit. Research suggested that it could be bearings and/or the spider shaft assembly. After watching the instruction videos to replace the spider or bearings, I seen you need to replace both the shaft seal and tub gasket to get to the spider and bearings. So I ordered both and waited for them to arrive. Plan was to disassemble the washer, determine what was needed, order the additional parts needed, and reassemble after the... Read more
Fixes loud banging during spin cycle and excessive vibration. Secures the drum spider assembly. Time-consuming repair (6 hours) but saves replacement costs.
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more
Creates watertight seal between washer drum halves. Replace if leaking during wash or spin cycles. Verify compatibility with your model number.
Secures the door boot gasket on your washer. Replace if seal pops off, leaks occur, or spring wire breaks. Confirm fit with your model number.
Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more
Fix a washer that won't drain or stops with a humming sound. This drain pump removes water during wash cycles. DIY repair takes about 10-30 minutes.
Replaced drain pump. Your video on your web site was very helpful. Read more
Prevents water leaks between washer tub and drum. Replace if you notice leaking, grinding noise, or water damage. Confirm fit with your model number.
Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more
Washer won't spin or shows 3C/3E error? Drive motor stator fixes grinding noises and spinning failures. DIY repair in 5-15 minutes with our video guide.
My washer would not spin. This fixed my problem only took me 5 minutes to uninstall and install. Read more
Washer not filling with water or showing 4E error? The water inlet valve controls flow into your machine. DIY repair in 15-40 minutes with video guide.
I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more
Fix a washer door that won't close or lock with this door latch assembly. Typical repair for broken latches takes about 15 minutes. Easy DIY install.
I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more
Fix 3E error codes or spinning issues with a rotor position sensor replacement. Detects motor position for smooth wash cycles. 15-minute DIY repair.
I watched the you tube video that completely explained how to do it. It was very easy to do. Read more
Replacement mounting bolt for washer counterweights. Secures balance weights to drum assembly. Order when bolt is broken, stripped, or missing.
I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more
Replace your broken or missing dryer control knob encoder assembly. This dial installs on the control panel to adjust cycle settings and temperatures.
Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more
Fix tub imbalance and loud clicking during wash cycle. This flange shaft assembly repairs broken spider arms. Challenging DIY repair, 4-6 hours.
Completely broke down washer and replaced part using the instructional video. Everything worked. We are still catching up on laundry. It's running like a champ now. Read more
Secures the inner door boot seal on front-load washers. Replace if seal is loose, leaking, or damaged. Confirm fit with your model number before ordering.
Fix excessive vibration and loud spinning noise in your washer. Balance ring assembly stabilizes the drum during spin cycles. Advanced DIY repair.
With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more
Fix a washer that won't fill with water or leaks onto the floor. This water inlet valve controls water flow into your machine. DIY repair in 10 minutes.
The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more