Hardware Hand Snowblower Carburetor Repair Parts

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

Secured the inner and outer door together and screwed handle back in place. Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more

First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you... Read more

We found the parts on this website. Thanks to your search bar, we could see if the parts would work on our model microwave. Read more

I ordered the mounting bracket, mounting hardware and template for the top cabinet. Everything I ordered was an exact fit. Install only took about 30 minutes after running the new electrical for the microwave. Appliance parts helped me save almost $400. Read more

Replacing the trim takes a little bit of alignment and light force. The trim slides over the glass panel of the door, with the glass sliding into plastic tabs. We kept the door nearly vertical (almost closed), lined up the tabs on the trim with the glass door, and used mild force to slide the trim down onto the glass door. (Also, we found that the tabs on trim we ordered were much bigger than the tabs on our broken trim. This is probably due to slight variations in Frigidaire's design over... Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door. The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time. I replaced the inside steel panel. Took about an hour. Was able... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more