Samsung Refrigerator Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Ice maker dispenses too much ice

I replaced the ice maker after replacing the ice try and before that the ice chute gasket. All easy fixes. However, I am still seeing some frost build-up leading me to believe that the issue is just a faulty design, which I have read other posts on. Just too much warm air gets in the ice maker because it is located in the refrigerator, plus warm air probably finds its way from the outside dispenser, up the chute into the ice maker. Oh well, nothing the occasional hair dryer won't take care of,... Read more

I noticed that the bottom of the plastic bucket was cracked even though it was less than two years old. I called Samsung and they wanted to charge me almost $200. Instead, I found the part at appliance parts pros for half that cost. Since I replaced the ice tray bucket assembly, my ice maker is working perfectly! Read more

• Fridge too warm
• Frost buildup
• Doesn't shut off

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

• Ice maker dispenses too much ice
• Ice maker not making ice

Since I could not find the correct thermistor from the schematic provided, I ordered the thermistor harness for the evaporator. I cut the harness and spliced it to the sheared thermistor wires on the roof of the freezer compartment. It now works fine with a little "farmer ingenuity" help. Samsung was absolutely no help at all, but the guy that I spoke with over the phone at APP sure was. This site is now my "go to" for appliance parts! Tip for others with this model. Do not overfill the upper... Read more

Slid out old bin and replaced it with the new one. No tools were required. Read more

• Leaking
• Not dispensing water

I called your company with the serial number of the fridge, and had the best service locating the exact items i needed. I placed by order . and company called to confirm my order and the method of my payment. Thank you very much Read more

I thought fixing this door would be too difficult/expensive, so I just spent a week manually closing the flap myself each time I closed the frig. Then I googled the model number of the frig just for fun. The first result was AppliancePartsPros.com, I clicked ONE SINGLE TIME and I arrived at this site, with the exact part I needed listed at the top, and a repair tutorial video that played beautifully with one more click. In the span of two total clicks, I saw how to fix the frig, and I saw... Read more

• Ice maker dispenses too much ice

This appears to be a weak spot on these refrigerators; the left-door ice maker will stop making (or at least consistently making) ice. Instead, an ice dam is created, which builds up in the ice maker corridor, making even getting the slide-in bucket nearly impossible to remove. The ice also freezes up the ice making tray, which therefore cannot drop the ice cubes. Generally, two things may go wrong which lead to this issue. The first is the ice-making assembly; its electrical components... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

Replaced fan motor, temperature sensor and defrost thermostat. Note: I had to replace connector on new defrost thermostat. Connector on new part did not fit mating connector in refrigerator.. spliced in old connector for new one. Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more

Repair went great thanks for your service Read more

Followed your instruction from your youTube instructions Read more

I ordered the French door housing, the new piece has a solid raised curved part that enters the guide, and a new center hinge. I watched both repair videos shown on appliance parts Pro. It looked pretty simple, so I got my 2 screw drivers and unplugged the refrigerator and started. The hardest part was removing the upper and lower hinges. The video didn’t show how he got them loose, after several minutes of frustration I figured out how to release the hinge. The new parts installed really... Read more

I loosened middle hinge by the 2 screws which holds a power cord that clips together, then slid the hinge flap upward to release from the door. My bottom clip hinge was broken away from spring and the only way to attach a new hinge clip was to carefully separate the hinge flap. This can be done by squeezing the flap to see where the separation seams are. Small narrow screwdrivers along with a spatula will do without damaging the plastic. This allowed for acess to the spring which connects to a... Read more