Parts for Maytag MHW6000AG2: 06 - Tub And Basket Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This rotor is the rotating core of the dishwasher's wash motor. Paired with the stator, it spins to drive water circulation through the spray arms, helping restore consistent spray action and cleaning performance.

• Works with the stator to create the magnetic rotation that powers the wash/circulation pump
• Failure can result in little or no spray action and poor cleaning results
• Can lead to intermittent wash or loss of circulation during the cycle

• Disconnect power and water supply before servicing
• Access the wash motor/sump from beneath the unit; removal from the cabinet may be required
• Remove the motor cover/retainer, pull the old rotor straight out, and fully seat the new rotor; handle magnet surfaces carefully
• Reassemble, restore connections, and run a short cycle to check for leaks and proper circulation

This replacement screw secures appliance components such as panels, brackets, and trim. Replacing a missing or damaged fastener restores a tight, rattle-free fit and helps keep your appliance assembled correctly after service or routine maintenance.

• Fastens panels, brackets, or covers to the cabinet/frame for proper alignment and support
• Replaces a stripped, corroded, or missing screw that no longer holds securely
• Helps reduce vibration and rattling caused by loose parts
• Useful when reinstalling components after repairs or part replacements

• Disconnect power; turn off water or gas to the appliance if applicable
• Use the correct driver size; hand-start threads to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Inspect the mating clip/threads and replace damaged hardware

This cap is a small protective cover used in select appliances. It helps secure and seal its mating component, preventing leaks, debris intrusion, or loosening during normal operation.

• Maintains a secure seal/cover over the designated fitting or opening
• Helps prevent leaks and contamination in the covered area
• Can resolve issues like minor leaks, loose or missing cap, or rattling noises
• Restores proper fit and finish after the original cap is lost or damaged

• Disconnect power and shut off water or gas supply before servicing
• Note the orientation of the original cap for correct placement
• Hand-tighten only unless the OEM specifies otherwise; do not overtighten
• Inspect the mating surface or threads for damage before reinstalling

This counterweight is a replacement door balance weight that helps stabilize an appliance door for smoother, more controlled opening and closing. It restores proper door balance and reduces sagging or uneven movement. What it does:

• Adds counterbalance weight to a refrigerator/freezer door assembly for correct alignment
• Helps prevent door sag, slamming, or uneven closing that can compromise the seal
• Reduces strain on hinges and ensures doors operate smoothly
• Quietly stabilizes the door during normal use

• One counterweight

• Disconnect power and empty/remove door contents before starting
• Follow the appliance service manual for door removal/installation; some steps may require two people
• Use appropriate hand tools and avoid forcing parts; retain fasteners for reuse

The Bellow is an OEM part for Whirlpool washing machines, designed to create a watertight seal between the washer door and the drum. This flexible rubber or silicone component prevents water from leaking out of the front-load washer during operation. 

Causes of a bad bellow can include regular wear and tear from constant use, exposure to harsh chemicals or detergents that degrade the rubber material, and the accumulation of foreign objects that can pierce or tear the bellow.

Symptoms of a bad Bellow include:

• Visible cracks, holes, or tears in the rubber
• Water leaking from the front door area during operation
• Mold or mildew smell coming from the bellow due to trapped moisture and debris
• Difficulty closing the washer door or an improper seal when the door is shut

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Inner Door Boot Seal Clamp is an OEM replacement part for Whirlpool front-loading washing machines. This clamp is responsible for securely holding the inner door boot seal in place. The door boot seal helps to prevent water leaks and contain washing processes. Its proper placement is ensured by this specialized clamp.

Causes of a bad clamp can include damage from over-tightening during installation and breaking or cracking over time due to normal use.

Symptoms of a bad Inner Door Boot Seal Clamp include:

• Gaps appearing around the edges of the door where water can seep or leak
• The inner boot seal not fitting or sitting flush any longer
• Developing puddles or drips of water outside the washer
• Visible water buildup inside the door seal cavity

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Some Kenmore models.

This drum baffle mounts inside the rotating drum and lifts items so they tumble evenly through the cycle. Replace a cracked, loose, or missing baffle to reduce noise and restore consistent tumbling performance. What it does:

• Lifts and separates laundry as the drum turns for even tumbling
• Helps prevent clumping that can lead to poor results or longer cycles
• Maintains balanced drum movement; damage or looseness can cause rattling or scraping
• May help if items aren't tumbling well, you hear thumping, or garments snag inside the drum

• 1 drum baffle

• Disconnect power before servicing; for gas dryers, also shut off gas. For washers, turn off water supply.
• Open the door and rotate the drum to access the baffle's mounting screw(s).
• Remove the screw(s), disengage the baffle from its slots, and lift it out.
• Seat the new baffle in the slots and secure with the screw(s). Hand-spin the drum to confirm clearance before use.

This spring-style hose clamp secures flexible appliance hoses to fittings, preventing leaks and keeping connections tight during operation. It's a small but critical fastener for reliable fluid containment. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to stop leaks
• Keeps drain, inlet, or recirculation hoses seated under pressure and vibration
• Helps prevent water damage and performance issues caused by loose hose connections

• Use pliers or a clamp tool to expand the spring clamp and slide it into position; release slowly to seat
• Inspect hose and fitting for damage and replace if cracked or worn before installing the clamp
• Disconnect power and water and follow appliance safety procedures before servicing

This replacement trap sits in the dishwasher's sump/filtration area and captures larger food particles before they reach the pump. It helps maintain cleaning performance and reduce clogs that can lead to poor wash results or draining issues.

• Screens debris to protect the wash and drain pump
• Helps maintain proper water circulation and draining
• Damage or warping can let debris bypass the filter system
• Symptoms include poor cleaning, standing water, unusual grinding noises, or odors

• Disconnect power and shut off water supply before servicing
• Remove the lower rack; take out the lower spray arm and filters to access the trap
• Release the trap's locking tabs/fasteners, remove, and seat the new trap fully
• Reinstall filters and spray arm; run a short cycle to check for leaks and proper operation

This small black clamp secures a hose, tube or wiring harness to prevent movement and abrasion. It's a direct-fit replacement used to keep connections stable so lines stay routed and protected during normal appliance operation. What it does

• Holds small hoses, tubing or wiring harnesses firmly in place
• Prevents chafing and accidental disconnection from vibration or movement
• Helps maintain routing to reduce stress on attached components
• Commonly used where a compact, non-corrosive clip is required

• Disconnect power before servicing any electrical appliances
• Use appropriate hand tools; avoid over-tightening which can damage hoses

The Tub Suspension Spring is an OEM part for Whirlpool washers. It is responsible for supporting and stabilizing the washer tub during the wash cycle. This spring ensures proper balance and reduces excessive vibrations and movement of the tub. 

A bad tub suspension spring can occur due to continuous use, heavy loads, or accidental mishandling. If you notice symptoms such as excessive shaking or vibrating during the wash cycle, loud banging noises, the washer moving or "walking" during operation, or leaks due to increased stress on the tub and other components, it may be time to replace the tub suspension spring set.

Symptoms of a bad tub suspension spring include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

Restore your washer by replacing the faulty or worn-out tub suspension spring with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Vent Hose is an OEM part for Whirlpool washers. This flexible hose is used to vent hot, moist air from the washer to the outside of your home, ensuring efficient operation by removing humidity and preventing mold growth inside the washer.

Over time, the vent hose can become clogged with debris, develop kinks, or suffer damage such as tears or holes. 

Causes of a bad vent hose can include the accumulation of lint or debris, physical damage from moving the washer, or general wear and tear over time.

Symptoms of a bad Vent Hose include:

• Longer drying times in washer-dryer combos
• Excessive humidity or mold growth inside the washer
• The washer feeling hotter than usual during operation
• Visible damage or kinks in the hose

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

The Water Pump is an OEM replacement part for Whirlpool washing machines. This component is responsible for circulating and draining water during the wash and rinse cycles, ensuring proper cleaning and rinsing of clothes.

Causes of needing to replace the water pump can include normal wear and tear over time, clogging or obstruction by debris or foreign objects, or mechanical failure due to excessive strain or motor burnout.

Symptoms of a faulty water pump include:

• Failure to drain water from the washer tub
• Leaking or standing water in the washer drum
• Unusual noises or vibrations during operation
•  Incomplete or insufficient water circulation during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

The Shock Absorber Washer is an OEM replacement part specific to Whirlpool-brand washing machines. It is a hydraulic device that absorbs the vibrations of the outer washer tub. Note: This is only one shock absorber.

Symptoms of worn or cracked shock absorber washers include:

• Noisy operation as the washer shakes or moves during cycles
• Physical signs of deterioration
• Over time, increased stresses can damage connected components

Causes involve many cycles of compression and release and solvents inside the washer degrading natural rubber. Deteriorated washers no longer absorb vibrations properly.  

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This shield is a protective cover that helps keep internal appliance components safe from heat, debris, and wear. Replacing a damaged shield restores protection to nearby parts and helps prevent further damage. What it does:

• Covers and protects internal components from debris, heat, and contact
• Helps prevent rubbing or chafing on wiring and nearby parts
• Reduces risk of heat-related damage when the original shield is warped or missing
• May stop rattling or vibration caused by a loose or broken shield

• Shield

• Disconnect power (and gas if applicable) before servicing
• Inspect the mounting area for damage or missing fasteners before installing
• Use the correct fasteners and alignment; do not force the shield into place

The Hose is an OEM part for Whirlpool washing machines. This hose is responsible for transporting water from the washer tub to the drain pump and then out to the external drain during the drain cycle. 

Causes of a bad drain hose can include regular wear and tear, blockages from debris, or cracking and splitting due to age and repeated use. 

Symptoms of a bad hose include:

• Water leaking from the washing machine during or after a cycle
• Slow or incomplete draining of water
• Visible cracks, splits, or other damage on the hose
• The washing machine stopping mid-cycle due to drainage problems

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This small replacement clip secures panels, trim, or wiring so appliance components stay properly positioned and the unit operates quietly. A simple, low-cost part that prevents loose pieces from shifting or rattling during use. What it does

• Holds trim, panels or harnesses in place to prevent movement and noise
• Keeps wiring or small components secured to reduce wear from vibration
• Helps maintain proper alignment of plastic or metal assemblies
• Commonly used where a simple snap-in retainer is required

• One clip/retainer

• Disconnect power (and water if applicable) before servicing the appliance
• Inspect surrounding parts for damage; replace any cracked or broken mounting features
• Typically installs with pliers or by hand; avoid forcing to prevent breakage

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This replacement seal restores a tight barrier between mating parts in your appliance, helping contain moisture at the joint. A fresh seal prevents leaks and supports proper performance when the original is worn, cracked, or compressed. What it does:

• Creates a moisture-tight seal between components to contain water at the connection
• Helps prevent drips, pooling, or seepage around the joint
• Replace if the seal is cracked, torn, flattened, deformed, or brittle
• Symptoms can include dampness at the joint, small leaks, or a loose fit

• 1 seal

• Disconnect power and shut off water supply before servicing
• Note the seal's orientation during removal to ensure correct placement
• Clean and dry mating surfaces; remove old residue or debris for a proper seal
• Seat the new seal evenly without twisting; verify full, uniform contact before reassembly

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

The Water Temperature Sensor is an OEM part for Whirlpool washing machines. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle. Note: The sensor does not include the seal WP8540766. Order separately if needed. 

Causes of a bad temperature sensor can be failures over time due to mechanical wear, thermal stress on electronic components, or damage from leaks/flooding inside the unit.

Symptoms of a bad water temperature sensor include:

• Inability to switch between wash steps or advance through the cycle
• Erratic or inconsistent temperature readings
• Failure alarms or error codes displayed
• Improper or incomplete washing even on high heat settings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This heater is the electric heating element that warms air or water so your appliance reaches the proper operating temperature. Replacing a failed heater restores normal heating performance and helps cycles finish correctly. What it does:

• Generates heat needed for normal drying or wash cycles
• Allows the appliance to reach and maintain operating temperature
• Common symptom: appliance runs but does not heat or takes much longer to finish
• Common symptom: cycles complete without expected temperature or sanitizing action

• One replacement heater element

• Turn power to the appliance off at the breaker before starting any repair
• Handle the element carefully to avoid bending or damaging terminals
• Follow the appliance service manual for panel removal and wiring re-connection

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.