Parts for Ge GTW540ASP2WS: Tub & Motor Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power

The Pressure Hose Assembly is an OEM component specially designed for GE top-load washing machines. It provides pressurized water transport from the water inlet valve to the machine components that require it. 

Located internally behind the washer casing, this tough braided hose reliably conveys water from the home supply plumbing. Its reinforced construction prevents kinks that could obstruct flow to critical parts like the dispenser drawer and pump chamber. 

Causes related to hose failure center around splits or cracks developing due to stress from repeated machine-generated pressure pulses over 10+ years.

Symptoms of a bad pressure hose include: 

• Reduced or inconsistent water levels during cycles   
• Water leaking/dripping inside unit from hosed areas
• Noticeable splits or cracks visible in braided casing

Replacing with this authentic GE OEM hose restores optimized water transmission. Proper flow supports thorough cleaning for washer units like Hotpoint, RCA, or Kenmore top-loaders.

This dual harness connector is a direct-fit replacement plug that secures two wire harnesses to restore a reliable electrical connection. It helps eliminate loose or intermittent wiring connections for affected appliance circuits. What it does:

• Provides a secure, snap-fit connection between two wire harnesses
• Restores continuity to circuits that show intermittent power, no power, or erratic operation
• Holds wiring in proper alignment to prevent accidental disconnection
• Used where a dual-wire plug mates to a control, switch, or component

• One dual harness connector

• Always disconnect power to the appliance before servicing
• Inspect wire ends and terminals for damage; replace or repair wiring if needed
• Use appropriate tools to seat the connector fully; do not force or bend terminals

The Impeller/Auger Base is an OEM part for GE washing machines. It is responsible for agitating the laundry within the wash tub, ensuring thorough cleaning by rotating and moving the clothes through the water and detergent.

Causes of a bad impeller/auger base can include general wear and tear from regular use, damage from overloading the washer, or debris getting lodged in the mechanism.

Symptoms of a bad impeller/auger base include:

• Poor cleaning performance
• Unusual noises during the wash cycle
• Washer not agitating properly
• Clothes remaining tangled or not evenly cleaned

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Impeller Cap is an OEM part for GE washers. As an integral part of the wash pump assembly, it covers and protects the impeller during operation. Located inside the wash tub, the impeller cap covers the spinning wash impeller that circulates water through the garments. 

Symptoms of a bad impeller cap include:  

• Excessive vibration or strange noises from the pump motor
• Reduced or inconsistent water pressure inside the tub  
• Broken or missing pieces found in the tub after cycles
• Premature failures of the impeller or pump bearing

Causes may involve cracks developing from mineral buildup or wear over time. Improper handling during maintenance can also warp weak points.  

This genuine GE replacement is compatible with Hotpoint, RCA and select Kenmore models.

The Washing Machine Screw is an OEM replacement part for GE washing machines. This screw is used to secure various components within the washing machine, such as the drum, control panel, or housing. While it may seem like a small part, the screw plays an important role in maintaining the structural integrity of the machine.

Causes for a bad or missing screw can include corrosion, loosening due to vibrations during wash cycles, or it may simply be missing due to repairs or disassembly.

Symptoms of a bad or missing Washing Machine Screw include:

• Unusual noises coming from the machine
• Components appearing loose or misaligned
• Increased vibrations during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Washer Hub is an OEM replacement part for GE washing machines. It is a central component located inside the washing machine basket that the inner tub, drive motor, and suspension springs connect to. The washer hub rotates the washing basket during agitation and spinning cycles to clean clothes thoroughly.

Constant rotational motion and vibration placed on the hub can potentially cause cracks or weakness over an extended time. Improper load balancing causing excessive shaking may also damage the hub.

Symptoms of a bad washer hub include: 

• The washing machine basket fails to spin or agitate properly
• Loud grinding or clicking noises coming from inside the machine  
• Vibrations felt through the cabinets or floor during cycles
• Misalignment or wobbling of the inner washing tub

This OEM GE replacement part is compatible with some Hotpoint, RCA, and Kenmore.

The Hub Nut Washer is an OEM part for GE washing machines. It functions to secure the hub and ensure that the drum remains properly aligned during wash and spin cycles, contributing to the smooth operation of the washing machine.

Causes of a bad hub nut washer can include wear and tear over time, excessive vibration or movement, or exposure to harsh detergents. A damaged or worn-out hub nut washer can lead to issues with the drum's stability, affecting the overall performance of the washing machine.

Symptoms of a bad Hub Nut Washer include:

• Excessive noise or vibration during wash cycles
• The drum not spinning correctly or being misaligned
• Leaks around the drum area
• Loose or wobbly drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Hub nut is an OEM part for GE washing machines, designed to securely fasten the tub assembly to the drive system of the washer. This component is crucial for the stability and operation of the washing machine's drum, ensuring that it remains properly aligned and attached during the vigorous motion of the wash cycles.

Per the manufacturer due to the high torgue on the hub nut an impact wrench should be used to remove and replace the hub nut. It also rquires a 90 ft lb torque limiting extension WX05X10028 and a 1 5/16th impact socket WX05X10022. You can order these through the links or use ones you already have. WARNING: The 90 ft lb torque limiting extension must be used when removing or installing the hub nut to prevent damage to the hub nut and transmission due to over torquing with the impact wrench. 

Causes of these issues can range from natural wear and tear over time to improper installation or overloading of the washer, which can exert undue stress on the Nut Hub and other related components. Ensuring that the Nut Hub is in good condition and properly tightened is essential for the longevity and proper function of your GE washing machine.

Symptoms of a faulty Hub nut include:

• Unusual noises during the spin cycle, indicating that the drum may be loose or off-balance
• The washing machine's drum exhibiting excessive movement or vibration beyond normal levels
• Water leaks from the area surrounding the drum

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This belt protector is a replacement cover that shields the dryer drive belt and nearby components from damage, helping maintain smooth drum rotation and prevent premature belt wear. What it does:

• Covers and protects the dryer drive belt from contact with the cabinet and foreign objects
• Helps prevent belt fraying and rubbing that can cause noise or reduced performance
• Keeps lint and debris away from the belt path to reduce overheating risk
• Supports proper belt routing for consistent drum movement

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer top or rear panel—use basic hand tools
• Inspect the drive belt and idler for wear while the protector is off; replace if damaged

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

This platform bearing retainer and fasteners secure the dryer drum/platform bearing assembly, restoring stable drum support and reducing wobble or noise. Use this retainer kit when the existing retainer is cracked, worn, or missing hardware. What it does:

• Holds the platform bearing in place to maintain proper drum alignment and rotation
• Helps stop excessive drum movement, knocking, or squealing caused by a loose retainer
• Replaces damaged or missing fasteners that can allow bearing shift or misalignment
• Works with the existing bearing and platform to restore correct support

• One platform bearing retainer and the specified fasteners shown on the OEM parts list

• Intended for technicians or experienced DIYers; inspect surrounding bearings and seals while replacing the retainer
• Follow the appliance manufacturer's service manual for disassembly/reassembly steps and torque specs
• Unplug the appliance or disconnect power before starting any repair to avoid shock or injury
• Replace any worn bearings or hardware discovered during installation to prevent repeat issues

The Spring is an OEM part for GE front-loading washing machines. It is responsible for assisting with the opening and closing of the washer door during the loading and unloading of clothes.

Causes of a bad spring can include cracks or fractures from repeated flexing over thousands of cycles. Stress and damage from excessively heavy loads or forced/slammed door movements can hasten spring failure.

Symptoms of a failed spring include:

• The door being hard to open/close or moving too freely
• An inability to hold the door securely closed
• Unnecessary noise and vibration from the door

Replace the worn spring with this genuine GE OEM part to restore proper function and balance to the door. It is designed for precise performance and durability. This replacement is also compatible with some Kenmore machines using GE components.

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

The Washer Shift Actuator is an OEM part for GE washing machines. This component is responsible for transitioning the washer between agitating and spinning modes. By engaging and disengaging the transmission or motor, the mode shifter allows the washer to shift from the wash cycle's agitation motion to the high-speed spin necessary to extract water from the laundry. 

Causes for replacement often stem from wear and tear due to regular use, mechanical failures within the component, or electrical issues that prevent proper operation.  

Symptoms of a bad Washer Shift Actuator include:

• The washer fails to switch between agitating and spinning modes.
• Unusual noises or grinding sounds during the wash cycle, indicating mechanical struggles.
• The laundry is still soaking wet after the cycle ends, suggesting the spin cycle did not engage properly.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Clutch is an OEM part for GE washing machines. This component is essential for engaging the washer’s transmission to facilitate the proper spinning and agitating of the drum during wash cycles.

Over time, the clutch can wear out or become damaged due to frequent use, heavy loads, or mechanical stress. Replacing a faulty clutch is crucial for maintaining the washer’s performance and efficiency.

Symptoms of a bad clutch include:

• The washer failing to spin or agitate
• Unusual noises during the wash cycle, such as grinding or whining
• Clothes remaining wet after the spin cycle
• The drum not rotating smoothly or at all

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Clutch Spring is an OEM part for GE washing machines. The spring allows the clutch to engage and disengage with the spin mechanism, facilitating the transition between the wash and spin cycles. 

Over time, the Clutch Spring can wear out or become damaged, affecting the washer's ability to switch between cycles smoothly. 

Symptoms of a bad Clutch Spring include:

• The washing machine not spinning or spinning inadequately
• Clothes remaining wetter than usual after the spin cycle
• The washer making unusual noises during the spin cycle
• The machine struggling to transition between washing and spinning phases

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This GE Ball Joint Upper is an OEM part for GE washing machines. Designed to ensure smooth and stable movement of the washing drum, this ball joint plays a crucial role in the appliance's suspension system. 

A compromised ball joint can lead to a decline in the performance of the washing machine, making it essential to address the issue promptly.

Symptoms of a bad Ball Joint Upper include:

• Unusual noises during operation, especially during the spin cycle.
• The drum may seem to wobble or be off-balance.
• Excessive vibration of the machine, more than usual.
• Uneven wear of other suspension parts, leading to further maintenance issues.
• Potential leakage or damage to surrounding components due to misalignment.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Suspension Rod is an OEM part for GE washing machines. This component is crucial for stabilizing the washing machine drum during spin cycles, minimizing vibrations and ensuring smooth operation. The suspension rod measures approximately 25 inches.

You should replace the suspension rod if it becomes worn out or damaged. Common causes of a bad suspension rod include regular wear and tear, overloading the washing machine, or exposure to moisture and corrosive substances. When the suspension rod is compromised, it can affect the machine's balance and performance.

Symptoms of a bad suspension rod include:

• Excessive shaking or vibrating during the spin cycle
• The washing machine being off-balance or moving during operation
• Unusual banging or thumping noises
• Leaks due to increased stress on other components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Suspension Rod is an OEM part for GE washing machines. This component is crucial for stabilizing the washing machine drum during spin cycles, minimizing vibrations and ensuring smooth operation. The suspension rod measures approximately 25 inches.

You should replace the suspension rod if it becomes worn out or damaged. Common causes of a bad suspension rod include regular wear and tear, overloading the washing machine, or exposure to moisture and corrosive substances. When the suspension rod is compromised, it can affect the machine's balance and performance.

Symptoms of a bad suspension rod include:

• Excessive shaking or vibrating during the spin cycle
• The washing machine being off-balance or moving during operation
• Unusual banging or thumping noises
• Leaks due to increased stress on other components

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A general-purpose appliance grease used to lubricate moving parts and reduce friction for smoother operation. Helps protect metal components from wear and keeps mechanisms operating quietly and reliably. What it does:

• Lubricates gears, hinges, rollers and other moving parts to reduce friction and wear
• Helps stop or reduce squeaks, grinding noises and stiff or sticking movement
• Aids smooth operation of controls and mechanical linkages
• Provides light protection against corrosion on contact surfaces

• Disconnect power before servicing the appliance to avoid shock or injury
• Clean and dry the area to be lubricated; apply a light, even amount where parts make contact
• Avoid getting grease on electrical components, heating elements, or surfaces that require friction
• Wipe away excess lubricant and test operation before returning the appliance to regular use

The Drive Belt is an OEM part for GE washing machines. It connects the motor to the drum, enabling the drum to spin during the wash and spin cycles. This belt is crucial for the proper functioning of the washing machine, ensuring that clothes are thoroughly cleaned and water is effectively extracted.

Over time, the drive belt can wear out or break due to regular use, overloading, or improper tension. These factors can lead to a loss of connection between the motor and the drum, affecting the washer's performance.

Symptoms of a bad drive belt include:

• The drum not spinning or agitating
• Unusual noises such as squealing or thumping during operation
• The washer failing to complete cycles or properly clean clothes
• A burning smell coming from the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This pulley nut secures the washer's drive pulley to the shaft to keep the belt aligned and power transfer reliable. Replacing a worn or missing nut restores stable spin performance and helps prevent belt slippage and noise.

• Locks the drive pulley to the shaft for proper belt alignment and consistent power transfer
• A loose or stripped nut can cause pulley wobble, belt squeal, slippage, or the belt coming off
• Replace if the original nut is damaged, missing, or will not stay tight after adjustment

• Disconnect power and water supply; safely tip or elevate the washer for bottom access
• Remove the drive belt; hold the pulley while loosening the nut (verify thread direction—do not force)
• Hand-start the new nut to avoid cross-threading; tighten securely per service information and confirm pulley runs true
• Reinstall the belt, verify alignment, and rotate by hand before restoring power

This motor pulley and nut assembly secures the motor pulley to the motor shaft so the drive belt turns the drum or agitator smoothly. Replacing a worn pulley helps restore proper drive operation and reduces noise. What it does:

• Transfers motor rotation to the drive belt so the drum/agitation components rotate
• Keeps the pulley centered and secured on the motor shaft to prevent slipping
• Helps stop squealing, grinding or rubbing noises caused by a loose or damaged pulley
• Can reduce belt wear and prevent drum wobble from a misaligned pulley

• Disconnect power (and gas supply if applicable) before starting any repair
• Remove access panels and the belt as needed to reach the motor pulley
• Inspect surrounding parts (belt, idler, motor shaft) for wear and replace if damaged
• Tighten the nut securely to manufacturer spec and test the appliance for proper operation

The Transmission Pulley and Nut is an OEM part for GE washing machines, designed to play a crucial role in the operation of the appliance. This component is directly involved in the movement and control of the washer's drum, translating the motor's power into the spinning and agitation needed for the washing process. The pulley system ensures that the machine operates smoothly, providing the necessary tension and motion to the belt that drives the drum.

Causes of these issues can range from natural wear and tear over time to improper loading of the machine, which can place undue stress on the mechanical components. Regular maintenance, including checking the integrity and alignment of the pulley system, can help prevent these problems.

Symptoms of a faulty Transmission Pulley and Nut include:

• The washing machine failing to spin or agitate properly
• Unusual noises during the spin cycle, indicating a misalignment or wear in the pulley system
• The washer drum moving more slowly or erratically
• Visible wear or damage to the pulley or nut

This OEM GE  part is also compatible with Hotpoint, RCA, and some Kenmore models.

The 1/2 HP Motor and Nut is an OEM washing machine component specifically designed for GE top-load washers. It provides the primary power source for agitation and spinning motions. 

Centrally located inside the washer base, the sturdy universal motor efficiently rotates the drive shaft through a coupling and rear axle assembly. A large hexagonal nut secures this drive hub connection with the tub.

Symptoms of a bad motor include:  

• Failure to start or complete agitation/spin cycles
• Abnormal noises such as grinding or knocking sounds  
• Motor overheating or burnt smells detected

Causes relate to normal motor coil degradation from continuous load cycling. Replacing with this authentic GE OEM part restores optimized power and torque transmission for thorough cleaning. Compatible units include select Hotpoint, RCA, or Kenmore top-load models.
 

The Speed Sensor is an OEM part for GE washing machines. This sensor monitors the rotational speed of the drum and communicates with the control board to ensure the correct spin speeds during the wash and spin cycles. It helps maintain optimal performance and balance, contributing to efficient washing and energy usage.

Over time, the speed sensor can become faulty due to wear and tear, electrical issues, or damage from vibrations. If the sensor fails, the washing machine may not operate correctly, leading to various performance issues.

Symptoms of a bad speed sensor include:

• Washing machine not spinning or agitating
• Unbalanced loads and excessive vibrations
• Error codes related to spin or motor functions
• Irregular or erratic cycle times

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Pump Seal is an OEM part for GE washing machines. This seal ensures a watertight connection between the drain pump and the washer tub, preventing leaks during the draining process. It plays a critical role in maintaining the efficiency and cleanliness of the wash cycle by keeping water contained within the system.

Causes of a bad drain pump seal can include wear and tear from regular use, degradation due to exposure to harsh detergents or chemicals, or physical damage such as cracks or tears. A compromised seal can lead to water leakage and potentially damage other components of the washing machine.

Symptoms of a bad drain pump seal include:

• Water leaking from the bottom of the washer
• Unusual noises during the draining cycle
• The washer not draining properly
• Visible cracks or damage to the seal

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Pump is an OEM part for GE washing machines. It's engineered to remove the used water from the washer at the end of each cycle, ensuring the machine is properly emptied and ready for the next load. This component is responsible for the circulation and expulsion of water, playing a vital role in the washing machine's ability to clean clothes thoroughly.

Causes of a bad Drain Pump can include obstructions within the pump itself, such as small garments or debris that can block water flow, or mechanical failures like a burnt-out motor or damaged impeller blades. 

Symptoms of a bad Drain Pump include:

• Water remaining in the drum after the wash cycle has completed.
• The washing machine failing to start due to sensing water from a previous cycle.
• Unusual noises coming from the pump area

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Internal Drain Hose Asm is an OEM part for GE washers. It is the hose located inside the washer that channels drained water from the tub out to the external drain system. 

Proper drainage is essential for washer operation. Causes of a bad internal hose can include cracks, kinks, or holes developing over time, especially in hoses made of brittle plastic material. Mineral buildup can also obstruct flow.  

Symptoms of a bad Internal Drain Hose Asm include:

• Puddling or pooling of water inside the washer tub after cycles
• Water not fully draining or draining slowly from the tub  
• Leaks or wet surroundings near the back of the washer

This GE replacement hose ensures your washer continues draining efficiently. This is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Clamp is an OEM part for GE washers. It is used to securely fasten critical components like hoses, sensors, and wiring harnesses in place inside the washer cabinet. 

As a machine that handles water, chemicals, and moving parts, a washer requires many clamps to organize its internal systems. They ensure hoses and electrical wiring remain properly positioned and protected throughout years of operation. Without solid clamps, connections could loosen or detach, leading to leaks or electrical faults.

Causes of a bad clamp can include fatigue from constant vibration, outright breakage from impact or tension overload, or rust/corrosion damage over extended use. 

Symptoms of a failed clamp include:

• Loose, disconnected or damaged hoses and wiring  
• Water leaks from hose connections
• Electrical or sensor errors

The clamp is also compatible with some Kenmore and other brands that use GE components.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.