Parts for Maytag YMED5430PBK0: Cabinet Parts

Replacement cover panel for dryers. Installs on the exterior housing to restore appearance and protect internal components when original is cracked or damaged.

Mounts the washer top panel to the cabinet frame. Replace if screw is stripped, rusted, missing, or damaged during cabinet disassembly and repair work.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Dryer drum seal prevents heat loss and improves efficiency. Replace if you notice excessive lint, reduced drying performance, or visible wear. Confirm fit with your model number.

Protective cover that finishes and seals the designated area on your dryer. Replace if cracked, broken, or missing to restore a clean appearance.

Fix a dryer that won't start or runs intermittently with this electrical connector plug. Replaces damaged or corroded wiring harness connectors.

Fix rattling or gaps at the top of your dryer with this front top panel lock. Secures the panel to the cabinet frame for a tight, aligned fit.

Dryer won't stop spinning when door opens or won't start at all? The door switch likely failed. DIY repair in 10-20 minutes with basic tools.

6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.

Includes two bumpers and two locking clips for securing dryer panels. Replace if clips are broken or missing to prevent rattling. Confirm fit with your model.

Secures the front panel to the dryer cabinet. Replace if cracked, broken, or damaged during disassembly. Installs at the panel-to-cabinet seam.

Adjustable leveling leg threads into the dryer base to set height and stabilize the unit. Replace worn, missing, or damaged legs to eliminate rocking.

Fix a dryer that won't heat or has burning smell at the power connection. This terminal wire kit replaces burned wires and connectors. Easy DIY repair.

Seals the gap between drum and front panel to retain heat and reduce friction. Replace if worn, torn, or causing noise. Confirm fit with your model.

Flat head screw secures panels, brackets, or trim for a flush fit on your dishwasher. Replace worn or missing screws to prevent rattling and shifting.

Seals dryer door to prevent heat loss and improve efficiency. Replace when torn, frayed, or loose. Fits in door groove; may need adhesive for install.

Replaces cracked, damaged, or worn dryer inner door panel. Restores door appearance and structural support. Essential for maintaining a clean finish.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Fixes excessive vibration and rattling from dryer motor movement. This clamp secures the motor to its bracket, restoring stability. DIY-friendly repair.

Dishwasher leaking or rattling? This motor mount clamp secures the pump assembly to prevent movement, leaks, and vibration. Quick DIY fix.

Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.

Connects the dryer motor shaft to the drum belt. Replace if cracked, broken, or worn. Includes mounting hardware for secure motor-to-belt connection.

Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.

Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.

Why this belt?

• Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
• Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
• Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.

Fixes these common dryer problems

DIY install — about 15 minutes

1. Unplug dryer; remove lint screen housing & front panel.
2. Release belt tension at idler pulley; lift drum slightly to slide old belt off.
3. Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
4. Re-assemble, run test cycle - enjoy quiet, consistent tumbling.

Fix excessive dryer noise or vibration with a new motor base. This support bracket secures the motor assembly for stable alignment and quiet operation.

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Foam seal cushions and seals dryer components to reduce vibration and prevent air leaks. Replace if worn, cracked, compressed, or missing.

Replacement mounting bracket for dryer internal components. Secures panels and parts in proper position. Needed when original is cracked, bent, or missing.

Fix washer control issues with this switch mounting screw. Secures cycle selector switch in console for reliable function. Simple DIY fix in minutes.

Dryer door seal creates an airtight barrier to contain heat and improve efficiency. Replace if torn, cracked, or allowing air leaks. Confirm fit with your model number before ordering.

Dryer door won't latch or stay closed? This door catch bezel secures the door mechanism. Common fix for broken latches. Easy DIY repair for most users.

Dryer drum support pad provides cushioning and reduces noise during operation. Replace if worn, cracked, or causing rattling sounds. Confirm fit with your model.