Parts for Jenn-Air JDS1750FS0: Chassis Parts

Insulation panel that lines the oven door to provide thermal protection. Replace if torn, compressed, or missing to restore proper heat retention.

Replace cracked or worn door insulation on your range. This thermal barrier installs between the door panels to improve heat retention and efficiency.

Cable retainer strap for electric and gas ranges. Secures wiring harnesses in place. Replace if cracked, broken, or missing to properly hold cables.

Replacement clip for dishwashers. Secures components and panels in place. Replace if cracked, broken, or missing to restore proper assembly and fit.

If your oven runs hot or cold or exterior surfaces feel too warm, damaged cavity insulation may be the cause. This thermal barrier restores even heat.

Replacement mounting screw for ranges. Secures panels, trim pieces, control boards, and brackets. Order when original screws are missing, stripped, or damaged.

Replacement side panel that restores your range's exterior finish. Covers dents, scratches, or damaged cabinet trim. Easy-to-install cosmetic part.

Secures the terminal block to your range's back panel. Replace if stripped, corroded, or missing to ensure safe electrical connections. 10-32 size.

Seals oven door to prevent heat loss and maintain consistent temperature. Replace if frayed, flat, or allowing smoke/heat to escape. Clips install easily.

Broiler not working or heating unevenly? This broil element directs intense heat downward to brown food. Simple DIY repair—just 2 screws and wire swap.

Oven not heating or baking unevenly? The bake element generates heat for baking. Most DIYers replace it in 10-15 minutes with a screwdriver.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Front leveling foot adjusts range height for stability. Replaces cracked, broken, or missing feet. Ensures proper leveling to reduce vibration.

Protects oven cavity components from direct heat and maintains temperature distribution. Replace if damaged, warped, or missing to prevent heat wear.

Range door insulation clip secures insulation retainer between inner glass panels. Replace if loose, broken, or missing to maintain door seal integrity.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Structural support base for range drawer rail assembly. Replacement needed when original is cracked, broken, or warped causing misalignment or instability.

Adjustable leveling leg installs on the front or rear corners of your range. Replace if broken, cracked, or worn to stabilize and level your appliance.

Oven won't heat or both elements stopped working? A faulty thermal fuse cuts power to prevent overheating. Easy DIY fix with basic tools in under an hour.

Replacement mounting screw for securing appliance panels, trim, and internal components. Restores proper fastening when original screws are missing or stripped.

Service bracket for electric and gas ranges. Mounts internal components securely. Replace if bent, broken, or missing to restore proper structural support.

If your range has a strong burning smell or won't power on, the terminal block may be heat-damaged. This insulated connector restores safe power flow.

Replacement mounting screw for securing range panels, brackets, and internal components. Replace missing, stripped, or rusted screws to restore fit.

Light socket assembly houses your oven bulb and provides electrical connections to illuminate the interior. Replace when bulb won't stay secure or light fails.

Replaces dim, flickering, or burnt-out bulbs in refrigerators, ovens, and microwaves. Restores interior lighting for visibility. Verify fit with model.

Self-tapping screw secures panels, brackets, and trim to range frames and housings. Replace worn, missing, or stripped fasteners to restore fit.

Oven not heating to correct temperature or overheating? The temperature sensor monitors and maintains accurate oven temps. DIY repair in 30 minutes.

Secures cooktop panels, burner components, and trim pieces. Replace missing, stripped, or damaged screws to eliminate rattles and keep parts aligned.

Protects range wiring from heat, abrasion, and vibration damage. Replace when insulation is cracked, frayed, or exposed. Verify fit with your model number.

Mounting screw secures panels, control boards, and burners inside your range. Replace if lost, stripped, or corroded to keep components stable.

Replacement mounting spacer for ranges. Maintains proper alignment and clearance between components. Replace if missing, cracked, or worn to restore spacing.

Protective panel lining the bottom of your oven cavity. Replace if cracked, warped, or rusted from heat exposure and spills. Provides smooth surface.

Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.

Fix loose or burnt wire connections in your range with this wire connector. Essential for restoring power to burners or oven elements. Simple repair.

Replace a convection fan motor when your oven heats unevenly or the fan won't run during convection cycles. Includes motor, fan blade, and heating coil.

Support bracket for ranges. Provides structural support for internal components. Replace if cracked, bent, broken, or missing to restore stability.

Oven floor dirty or stained? This hidden floor pan protects the cavity from spills and debris while maintaining heat distribution. Direct fit.

Replace the air duct in your electric or gas range. This component channels airflow through the appliance and may need replacement if cracked or damaged.

Fix F8E0 error code or slow cooling fan in your range. This fan motor circulates air for even heating. Moderate DIY repair takes 1-2 hours to install.

This door channel secures the range door glass panel. Replace if the original is cracked, broken, or missing to restore proper door assembly and appearance.

Wire cover for electric and gas ranges. Protects and conceals wiring connections. Replace if cracked, broken, or missing to maintain safe appearance.

Rear cover panel for electric and gas ranges. Installs on the back of the range to protect internal components. Replace if cracked, damaged, or missing.

Adjustable oven rack shelf for electric and gas ranges. Replaces worn, warped, or missing racks to restore proper cookware support and oven airflow.

Replace bent, rusted, or missing oven racks to restore a stable cooking surface. This rack slides in and out smoothly for safe baking and roasting.

Replace a bent, worn, or missing oven rack in your range. Provides a sturdy shelf for bakeware and pans, ensuring cookware sits level and slides smoothly.

Replace a range power cord if the unit won't turn on or loses power intermittently. This cord connects your range to the wall outlet. DIY install in 15 minutes.

Replacement mounting bracket for electric and gas ranges. Secures components in place and restores proper alignment. Use to replace bent, broken, or missing brackets.

Intermittent power or heat damage at wire connections? This terminal block nut secures wire lugs to studs for a reliable electrical connection. Quick fix.