Lawn Mower Carburetor

This is a genuine OEM replacement float for use in a long list of snow throwers and lawn mowers. A float is a relay component of an engine's fuel tank. As its name suggests, it floats on top of the fuel in the tank, and as the liquid rises, it pushes the float upwards, blocking the float needle to prevent more fuel from entering the chamber. This helps prevent too much fuel from combusting, guaranteeing a balance of air and gasoline in the carburetor. Carburetor floats are generally designed to last the full lifetime of an engine, but they can occasionally wear out and need replacing. When this happens, the carburetor may begin to flood, causing fuel to leak from the engine. This poses a safety hazard and should be repaired as soon as possible. You will need a set of wrenches, socket wrenches, a screwdriver, and pliers to make this repair. This part is compatible with Cub Cadet, MTD, Craftsman, Toro, Tecumseh, and Lawn Boy snow throwers and lawn mowers and comes sourced from the original manufacturer. This is a high-quality replacement part and does not ship with additional hardware.

This carburetor nzle fits lawnmowers, lawn tractors, tillers, and other lawn and garden equipment. It is the part of the carburetor assembly that guides the fuel inside of the carburetor and maintains the proper fuel to air ratio. This is an essential part of engine performance. If the carburetor nzle is clogged, damaged, or broken, the engine will not run properly. The carburetor nzle can be replaced as a single repair or as part of an overall carburetor rebuild. Remove the carburetor float and float ring to get to the bowl. Remove the carburetor nzle from inside the carburetor throat with long nose pliers or by pressing it out manually. Ensure both o-rings come out with the nzle; if not, fish them out of the carburetor bowl. Install the o-rings on the new carburetor nzle before installation. This repair should be done in an area with adequate ventilation. Be sure to drain the fuel tank before removing the carburetor and take the spark plug off the engine.This carburetor nzle is sold as an individual unit. It is designed for lawn and garden equipment engines manufactured by Craftsman, Tecumseh, Cub Cadet, Lawn-Boy, and Toro.

The carburetor mixes air and gas to create combustible fuel for the engine to burn. If the carburetor or its seals are leaking or clogged, the correct amount of fuel will not reach the engine. When an engine runs rough or will not start at all, the carburetor may be clogged or damaged. It is possible that the engine is not receiving any fuel at all. If the engine is running rough or sputtering, the carburetor is likely clogged. If the engine will not start at all, it is more likely that the carburetor will need to be replaced. There are pieces to replace individual parts, or you can choose to replace and rebuild your whole carburetor. This carburetor diaphragm gasket kit is compatible with many manufacturers and various kinds of small engines in items like string trimmers, chainsaws, and more. It is a genuine OEM part.

The main nozzle is a part of the carburetor in pressure washers and snowblowers. This is a part of the carburetor assembly and it can be located between the carburetor bowl and carburetor body. It passes through the plastic float component. The nzle is used to direct air or water in the right direction when using the lawn and garden equipment. The main nzle can experience wear and tear or damage which will make it incapable of blowing air or water.If the nzle is broken or cracked, it needs to be replaced. A set of basic tools and work gloves will be useful during the process. First, the carburetor will need to be removed from the equipment. Disassemble the carburetor to gain access to the main nzle. Take the original component out and replace it with a new part. Make sure to reassemble all components before use.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The main nzle is designed for use in the carburetor of snowblowers and pressure washers manufactured by Lawn-Boy, Briggs & Stratton, Toro, and Tecumseh.

A primer bulb works to lubricate the engine with oil by pressing in the rounded tip of the primer bulb. It measures an inch in diameter and an inch tall. Over time these parts can wear out from sun exposure, contact with chemicals, or dry rot. The gasket may wear out before the primer bulb, so it is important to check this part regularly to discover any damage. Installing the new primer bulb kit should be easy and only take a few minutes. Only a screwdriver set and pliers are needed to complete this repair. This primer bulb kit works in conjunction with small engines, lawnmowers, log splitters, and pressure washers made by brands Briggs & Stratton, Craftsman, Cub Cadet, Lawn-Boy, MTD, Tecumseh, and Toro. It is a genuine OEM part and is sold individually.

Governor links are used on lawn and garden equipment engines. This component is used to adjust the throttle of a lawnmower or pressure washer so it works at a consistent speed. If the tool is running only at a low or a high speed, the governor might need to be adjusted or set. In some cases, the governor link may go bad or become damaged and require replacement.The first step is to inspect the governor link and springs to ensure they are operated correctly and not damaged or stretched out. Check the governor static adjustment to see if all free play has been removed between the carburetor and spindle by moving the throttle from idle to open and watching how the shaft moves. If it moves clockwise, loosen the clamp screw, turn the shaft all the way around, and retighten the nut. If it does not move freely after this, the part may need to be replaced.This governor link works with lawnmowers, pressure washers, snowblowers, and tillers by Tecumseh, Briggs & Stratton, Cub Cadet, Toro, and Craftsman. It is a genuine OEM product that is directly sourced through the manufacturer. It comes as a single component.

The primary function of a carburetor is to mix fuel and air in the right ratio. Fuel enters the carburetor through the fuel inlet fitting and then to the float bowl which delivers fuel to the other circuits. From there, the fuel goes to the needle valve, which is actuated by the float. When there is insufficient fuel, the float will stay down, keeping the valve open. Once the chamber has enough fuel, the float will go up and close the valve. A failed float bowl may leak or have too many dirt particles deposits that impede fuel flow. Luckily, you can easily replace a busted float bowl. This part is a genuine OEM Tecumseh 631867 float bowl replacement. You’ll have the assurance that this replacement is manufactured according to Tecumseh’s highest standards. It is compatible with mowers, tractors, and snowblowers from Toro, Cub Cadet, Lawn-Boy, MTD, and Tecumseh. This part is sold individually.

This is a replacement carburetor for use with various types of small engines. The role of the carburetor in the engine should never be overlooked. This part is responsible for providing the correct air and fuel mixture to the engine, so it can start and continue to run properly. In time, there may be issues with the carburetor. Parts of the carb could fail or become corroded and need to be replaced. To get a better idea of whether the carburetor is the problem, owners can remove the oil filter and add a teaspoon of fuel directly to it. Then, they will start the engine. If the engine starts, but stalls after a few seconds, it could be the carburetor. It should be replaced soon to ensure the engine continues to start and perform well. This is a genuine OEM replacement carburetor that is sold individually. It does come with the needed gaskets. The carburetor can be used on various models of log splitter, mowers, and other small engines. Compatible brands include Tecumseh, Craftsman, and MTD.

This is a carburetor bowl. It holds the gas that is mixed with air before it enters the engine. The carburetor bowl contains a float which regulates the amount of gas needed to mix and fuel the engine.There are times when the carburetor in of itself is considered in good working order but the bowl may be compromised. This can happen if the bowl has been corroded. Rust will damage the carburetor bowl and render it ineffective. When replacing the carburetor bowl, be sure to work in a well-ventilated area and to wear the proper gear when handling engine parts. Once the carburetor is free from the engine, unscrew the bowl from the unit over a catch pan. Any contents will fall into the pan. Disassemble the old bowl's hardware and use it when installing the new bowl.This is a genuine OEM part manufactured by Tecumseh. It is compatible for Toro, Cub Cadet, and MTD engines.

This part is an inlet needle. This inlet needle works like a valve to transport fuel into the carburetor bowl when the bowl has drained and then stops fuel intake when the carburetor bowl is full. A new inlet needle may be needed if the fuel is not flowing into the bowl as it is supposed to. This can be evident if the carburetor floods or if the engine does not have enough fuel when it's operating at high speeds. A visual inspection of the inlet needle can also be a good indicator of whether or not it needs to be replaced. If any physical signs of damage are present, the inlet needle will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine Tecumseh part and is an OEM part sourced directly from the manufacturer and it is sold individually. This inlet needle is compatible with snowblowers manufactured by Tecumseh and Toro.