Parts for Whirlpool WTW8100BW0: 02 - Motor, Basket And Tub Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This impeller cap fits over the dishwasher's wash pump impeller to secure it in place and help maintain proper water flow and spray pressure for effective cleaning. Replacing a cracked or missing cap can reduce noise and restore consistent performance.

• Secures the wash pump impeller and helps prevent wobble or rubbing
• Helps maintain proper water circulation to the spray arms
• Common symptoms of a failed/missing cap: poor cleaning, unusual grinding/rattling noises, or visible damage in the pump area
• Designed for the specific pump/sump design used on select models

• Disconnect power and turn off water supply before servicing
• Access the pump from inside the tub; remove the lower rack, spray arm, and filter/cover as required
• Note cap orientation; press or twist-lock fully onto the impeller (reuse any existing fastener if your model uses one)
• Inspect the impeller and seals while accessible; replace worn parts as needed

The Agitator Bolt is an OEM part for Whirlpool washing machines. This bolt secures the agitator in the center of the wash basket, ensuring it remains firmly in place during the wash and spin cycles. 

Causes of a bad agitator bolt can include regular wear and tear, corrosion due to exposure to water and detergents, or being loosened or damaged by heavy loads or improper handling during maintenance.

Symptoms of a bad agitator bolt include:

• The agitator wobbling or coming loose during cycles
• Unusual noises coming from the washer during agitation
• The agitator not turning properly, resulting in poor cleaning performance
• The bolt showing visible signs of rust or damage

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.

• Mounts to the drive hub to rotate and circulate laundry during the wash cycle
• Helps create water currents and friction to loosen soils
• Worn or stripped splines can cause slipping and poor agitation
• Common symptoms: clothes not moving, poor cleaning results, unusual clicking/grinding from the tub base, visible cracks or wobble

• Disconnect power and shut off water before servicing
• Remove the center cap/cover, then remove the retaining bolt and lift off the old washplate
• Clean and inspect the hub splines; seat the new plate fully and reinstall the bolt—do not overtighten
• Run a short test cycle to ensure proper wash action

The Whirlpool screw is an OEM replacement part responsible for securing various components and parts of your washing machine. These screws are designed to fasten different elements within the appliance, ensuring their stability and proper functioning. The specific location of these screws can vary depending on the washing machine model and design, but they are commonly used to secure panels, brackets, and other components in place.

This part fixes the following symptoms

• Excessive vibration or shaking during the wash or spin cycles
• Loud or unusual noises coming from the appliance
• Loose or wobbly parts within the machine
• Panels or components that become detached or dislodged
• Difficulty in assembling or disassembling parts during maintenance or repair

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Washer Basket Hub is an OEM part for Whirlpool washing machines. It is designed to connect the washer basket to the drive shaft, enabling the basket to spin during the wash and spin cycles. This component ensures that the basket rotates smoothly and efficiently, contributing to the overall performance and functionality of the washing machine.

You should replace the washer basket hub if it becomes worn out or damaged. Causes of a bad basket hub can include regular wear and tear from frequent use, corrosion due to water exposure, or damage from overloading the washer. A faulty basket hub can impair the spinning action, leading to inefficient washing and rinsing.

Symptoms of a bad washer basket hub include:

• The washer basket not spinning or agitating properly
• Loud noises such as grinding or clunking during spin cycles
• The washer failing to complete cycles or properly clean clothes
• The basket being loose or wobbling during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Washer Basket Hub is an OEM part for Whirlpool washing machines. It is designed to connect the washer basket to the drive shaft, enabling the basket to spin during the wash and spin cycles. This component ensures that the basket rotates smoothly and efficiently, contributing to the overall performance and functionality of the washing machine.

You should replace the washer basket hub if it becomes worn out or damaged. Causes of a bad basket hub can include regular wear and tear from frequent use, corrosion due to water exposure, or damage from overloading the washer. A faulty basket hub can impair the spinning action, leading to inefficient washing and rinsing.

Symptoms of a bad washer basket hub include:

• The washer basket not spinning or agitating properly
• Loud noises such as grinding or clunking during spin cycles
• The washer failing to complete cycles or properly clean clothes
• The basket being loose or wobbling during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part is a replacement outer tub. This part can be used to replace broken or defective outer tub in a variety of dryer models. The outer tub is critical for proper dryer functionality as it's what holds water that is emitted from materials or clothes as they dry. If this part is corroded, cracked, dented, bent, or otherwise rendered ineffective, the user may notice leaking, clothes not being dried properly, or other issues. Thus, the outer tub will need to be replaced. Before any repairs are made, the appliance should be entirely disconnected from the power sources and work gloves should be worn.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. As an authentic replacement part, this outer tub is suitable for use on dryer manufactured by Whirlpool, Maytag, Kenmore, and some other brands. This part is sold individually.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

Motor shield bumper kit includes 4 bumpers. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

This motor stator is the stationary windings for a direct-drive washer motor. Working with the rotor, it creates the magnetic field that turns the basket. Replacing a failed stator restores consistent wash and spin performance. What it does

• Provides the fixed windings for the direct-drive motor
• Works with the rotor to spin and tumble the basket
• Failure can cause no spin/tumble, intermittent movement, or loud humming
• May lead to motor/speed-related error codes and cycle shutdowns

• 1 motor stator assembly

• Disconnect power before servicing; allow moving parts to stop
• Access is typically from the rear; remove the rotor to expose the stator
• Handle the rotor's strong magnets carefully and keep metal objects clear
• Route and seat the wiring exactly as original; tighten mounting bolts evenly

This plate stator is the stationary motor plate used in compatible Whirlpool appliance motor assemblies. It supports the motor's stationary components so the motor can run smoothly and reliably. What it does:

• Secures and positions the motor's stationary winding and magnetic components
• Helps maintain correct air gap between rotor and stator for proper motor function
• Can contribute to noisy motor operation or failure-to-start when damaged
• Supports consistent motor rotation and reduces abnormal vibration

• Disconnect power to the appliance before starting any repair.
• Removal typically requires disassembly of the motor housing; retain fasteners and note orientation.
• Handle carefully—edges and mounting holes can be sharp and fragile.

The Rotor Position Sensor is an OEM part for Whirlpool washing machines. It is responsible for monitoring the position and speed of the rotor, ensuring the motor operates correctly to perform various washing cycles. The sensor sends precise data to the washing machine's control board, which adjusts the motor's function accordingly.

Causes of a bad rotor position sensor can include electrical failures, wear and tear over time, or physical damage from impact or moisture exposure. When this sensor fails, it disrupts the communication between the motor and control board, leading to operational issues.

Symptoms of a bad rotor position sensor include:

• The washing machine not spinning or agitating
• Error codes indicating motor issues
• The machine stopping mid-cycle
• Unusual noises coming from the motor area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

The Bearing Installation Tool is an OEM part for Whirlpool washing machines. This tool is specifically designed to aid in the installation of bearings in the washing machine tub, ensuring proper alignment and secure placement.

This tool is essential for replacing worn-out or damaged bearings, which can affect the performance of the washing machine. Over time, bearings can wear out due to continuous usage, exposure to moisture, or heavy loads. Using this tool ensures that new bearings are installed correctly, preventing potential issues caused by misalignment or improper installation.

Symptoms of bad bearings include:

• Loud, grinding noises during the spin cycle
• Excessive vibration or movement of the washer
• Leaks from the tub area
• The drum not spinning smoothly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Used to install the bearings in the bearing and tub seal kit, part number: W10435302. When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model.

The Bearing and Tub Seal Kit is an OEM part for Whirlpool washing machines. It includes high-quality bearings and a tub seal designed to ensure smooth operation and prevent water leaks. The bearings allow the tub to spin freely and quietly, while the seal protects the bearings from water and detergent, extending their life and the overall efficiency of the washing machine.

Causes of failure for these components can vary but often include water infiltration that leads to rust and deterioration of the bearings, or wear and tear from heavy or unbalanced loads that put additional stress on the seal and bearings. 

Symptoms of a bad bearing and tub seal kit include:

• Noisy operation, especially during the spin cycle
• Water leaking from the bottom of the washer
• The washing machine tub struggling to spin or not spinning at all

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.