Parts for Maytag SDE5401AYQ: Motor, Fan & Belt Parts

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

The Dryer Motor is an OEM part for Whirlpool dryers. It is a vital component that provides the necessary power and rotation to tumble the dryer drum, allowing for the proper drying of clothes and linens.

Causes of a bad dryer motor can include excessive wear and tear over time, electrical malfunctions, or physical damage from impact or overloading. Symptoms of a faulty motor may include:

• The dryer drum not rotating or tumbling
• Loud grinding or squeaking noises during operation
• Burning smells or excessive heat buildup
• Failure to start or run completely

 This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

Considered a crucial part of the dryer, the blower fan assembly is the part that pulls in air from outside and then circulates that air in the drum to ensure clothing gets dry. After the air is moved around the drum, it is then moved through the exhaust vent. This part is located on the motor shaft and is made of durable plastic. Regular use can lead to wear and tear or damage to this component. If this occurs, the air in the dryer may not dry the clothing. In this case, the blower fan assembly will need to be replaced.If the blower fan assembly needs to be replaced, first the dryer should be unplugged from power. Take the cabinet top off and remove the front panel on the appliance. Take out the drum, remove the motor clamp, and loosen the blower fan so it can be removed. Take it out and replace it with the new blower fan assembly.The blower fan assembly is designed to be used with dryers manufactured by Amana and Speed Queen. It is sold as an individual part. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This thermostat is a temperature-sensitive switch used in the appliance's heating circuit. It opens and closes at a specific temperature to regulate or limit heat, helping maintain correct operation and protect components from damage due to overheating.

• Monitors temperature and switches the heating circuit on/off at its preset trip point
• Helps prevent overheating and heat-related component damage
• Failure symptoms can include no heat or underheating, overheating or burnt odors, or heat that won't shut off
• May cause intermittent heating or frequent cycling as the unit warms and cools

• Disconnect power and allow the appliance to cool completely; shut off gas supply if applicable
• Access the thermostat, note/photograph wire positions, and transfer wires one at a time to the new part
• Mount securely against the proper surface/bracket so the sensor has good contact
• Restore power and test operation; if issues persist, diagnose related heating components per the service manual

This multi-temperature cycling thermostat regulates the dryer's drum heat, switching the heater on and off to match the temperature setting you choose. It can help restore consistent drying if temperatures are erratic, loads run too hot, or cycles take too long.

• Maintains target temperature by opening and closing the heater circuit across multiple heat settings
• Provides calibrated temperature control for safe, efficient drying
• Failure may present as no heat or low heat, overheating, very long dry times, or inconsistent temperatures
• Intended for models with multiple temperature selections

• Unplug the dryer; shut off gas supply if applicable. Allow the appliance to cool before servicing.
• Take a photo of wire positions; move wires to the new thermostat one at a time to matching terminals and ensure snug connections.
• Remove/install mounting screws and seat the thermostat flat against the mating surface for proper sensing.
• After reassembly, clear lint passages and verify proper vent airflow.

• If there's no heat at all, also check the thermal fuse, high-limit thermostat, heating element (electric), or igniter/burner components (gas).
• Restricted venting can mimic thermostat issues and cause overheating or long dry times.

This is the idler tension spring that holds the dryer belt tight for smooth drum rotation and reliable drying. It restores proper belt tension to help eliminate slipping and uneven drum movement. What it does:

• Applies tension to the dryer idler assembly so the belt stays engaged with the drum and motor pulley
• Helps stop belt slippage that can cause the drum to not turn or to turn intermittently
• Reduces squealing or rubbing noises caused by a loose or worn tension spring
• Works with the idler pulley and belt to maintain consistent drum rotation during operation

• 1 idler tension spring

• Disconnect power to the appliance before any service to prevent shock or injury
• Access may require removing the dryer front or top; follow OEM service instructions for your model
• Relieve belt tension carefully when removing/installing the spring; use gloves and eye protection
• After installation, verify proper belt alignment and test a short cycle to confirm normal operation

For complete assembly for easier installation order WP37001287

The Thrust Washer is an OEM part for Whirlpool washers and dryers, reduces friction between moving parts within the appliance. This small component is placed between rotating surfaces to ensure smooth operation and to extend the lifespan of those parts. The thrust washer can wear down or become damaged due to the constant pressure and movement.

Causes for replacement may include normal wear and tear, overloading the appliance, which puts extra stress on mechanical components, or a lack of regular maintenance.  

Symptoms of a bad Thrust Washer include:

• Increased noise during operation
• The appliance vibrating more than usual
• A decrease in performance efficiency

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Belt Tension Pulley is an OEM part for Whirlpool clothes dryers. It utilizes a tension mechanism to maintain precise alignment and contact between the drive belts and motor pulleys during operation.

Symptoms of a failed belt tension pulley include:

• Extended dry times or inability to dry clothes fully
• Abnormal noise or vibration coming from inside the dryer
• Premature belt wear requiring frequent replacement
• Error codes appearing or inability to start cycles

Causes of a bad pulley can include cracks, defects, or stiffness in the tension mechanism limiting its range of motion from years of operation. Lubricant breakdown within the pulley can also produce excessive friction or noise over time.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Retaining Ring is an OEM replacement part for Whirlpool dryers and washing machines. This retaining ring holds the rear wheels on the axels of the washer or dryer. 

Symptoms of a bad retaining ring can include wear and tear over time, damage due to accident or impact, or corrosion affecting the structural integrity.

Causes of a bad retaining ring dryer include:

• Excessive vibration or movement of the drum during operation 
• Noise or banging sounds from loose components   
• Deformation or cracking of the retaining ring itself
• The dryer door not closing properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 1/4-20 nut secures related fasteners in appliance assemblies to keep components aligned and stable. It's a direct-fit replacement when the original nut is worn, stripped, or missing. What it does:

• Threads onto a 1/4-20 bolt or stud to lock parts together
• Restores tight mechanical connections that reduce vibration and noise
• Helps maintain proper alignment of panels, brackets, or linkage
• Commonly replaced when the original nut is rounded, corroded, or loose

• One 1/4-20 nut

• Use the correct 1/4-20 bolt or stud size and thread engagement
• Tighten to manufacturer torque if specified; avoid over-tightening
• Inspect adjoining parts (bolt, washer, bracket) for wear before reassembly
• Turn off and unplug the appliance before performing repairs