Search Results

Took it apart and replaced it. Read more

After checking the suggested fixes and parts on Appliance Parts Pros, I ordered the defrost thermostat and evap motor for my refrigerator, a Kitchen Aid KSSC42QTS00. Installation was very easy, simply emptying the freezer and removing the access panel in the back bottom half. Upon getting everything open, I found out that the existing evap motor was working fine, so I didn't install that part. I did install the defrost thermometer, which was a 5-minute process. I also cleared out the vent... Read more

Replaced the auger motor. Read more

I replaced the defrost thermostat and the fan motor. Very impressed with service. Ordered the parts Thursday night and they where on my porch Saturday morning. Read more

Went to appliance parts pros and typed in the problem, and they had a video on that problem and how to fix it, easy fix, ordered the part, had it 2 days later, took my washer apart while I was waiting for the part to come, and then reviewed the video several times, and then completed my repair, probably saved 150-200 dollars by doing it myself, also had my dryer conk out last year, did the same thing, looked up the problem, ordered the part, and made the repair, the pair is 20 years old, parts... Read more

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

Checked and found the evaporator frozen causing the fan to stop working. Took the interior panels off and applied a blow dryer to the ice, once the ice melted I cut the tabs on the grommet holding the fan since everything is thin plastic and replaced the grommet and fan. Placed everything back and found no further issues. Tools I used were a small flat head screwdriver to pry the panels off and a 1/4 socket to remove the center drawer (4), water filter cover (2), and the ice maker (2). Not too... Read more

Very easy to replace. Take off cover to auger compartment. Unplug power connector from auger motor. Remove four screws holding auger motor to refrig. Put new auger motor in place, insert screws, insert power connector, replace cover. Use ice maker! Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more

After removing the rear panel, I vacuumed the area. Then was easy to see condenser fan not spinning. I replaced the fan with a compression ring and a fan motor. First pulled the wiring harness connected to fan motor, then pulled off the fan with hands. Then used a wrench to remove 2 bolts for the motor. Next, pushed on new fan and screwed in the 2 bolts for the motor. Initially, I purchased a new temperature control to replace as well but after replacing fan and motor, I believe it was still... Read more

• Freezer section too warm
• Noisy
• Fridge too warm

I googled the issue and read several articles. Most started with cleaning the coils (which mine are on the bottom) (19yr old Kenmore 363.9557812). I had not really ever cleaned them well, vacuuming did little. I had to remove the cardboard cover off the back of the frig, and blew them clean (front to back). Once that was done, I started cleaning from the back and noticed the fan wasn't turning week (condensor fan). Blew it out too, have it a good soon with a pencil, it puffed out a bunch of... Read more

Replaced rotor assembly due to hub being stripped. New part was upgraded with steel insert. After watching youtube video on AppliancePartsPros site, it took about 15 minutes for entire job. Part arrived in two days. Great service. Read more

Replaced the fan Read more

• Oven not heating evenly
• temperature not accurate

First I did a search for my model stove, I read the discriptions of what it was doing and came to the conclusion it was the fan motor. I then called an appliance dealer in my local area to find out that the fan motor cost all most double what I could get it online. I called to see how much it would cost to have a repair man come out and fix it, which would have cost 260 dollars. So in one of the suggested comments that someone previously left it stated that it could be done in about 20... Read more

When I looked up LG washer E6 code on the web I saw the tip from LG: unplug the washer and call for service. To me that's a challenge. I saw the AppliancePartsPros.com story on Google, read it and decided to try the solution that worked for other people. A clutch shifter motor that was around $20. I checked a few local appliance parts stores and no one carried the part I needed in stock (even though their websites said available for pickup). I then ordered the part through AppliancePartsPros on... Read more