Need Help?
Call or text
Show parts
Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.
Dishwasher not washing or draining? This pump and motor assembly powers the wash and drain cycles. Requires dishwasher removal for installation.
This part is discontinued by the manufacturer and is no longer available for purchase.
Dishwasher won't drain or makes loud humming noise? This drain pump removes water from the wash cycle. Moderate DIY repair with unit removal required.
Mounting bracket that secures the drain pump in place inside your dishwasher. Replace if the original is cracked, broken, or missing to properly support the pump.
Usually ships within 4 - 14 days
Dishwasher won't drain or drains slowly? A worn check valve flapper may be blocking water flow. This 30-minute DIY fix prevents backflow issues.
Secures dishwasher hoses to fittings and prevents leaks. Replace if corroded, rusted, or loose to restore a watertight seal. Confirm fit with your model.
Secures hoses to fittings for leak-free operation. Replace when worn or corroded to stop drips on fill, drain, or circulation lines. Confirm fit.
Secures hose connections to prevent leaks in your dishwasher. Replace if water pools under the unit or connections feel loose. Confirm fit with your model.
Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Needed when original screws are stripped, missing, or lost.
Secures the dishwasher pump motor to the appliance frame. Replace if bracket is cracked, broken, or worn to restore motor stability and prevent vibration.
Rubber grommet seals openings where hoses and wires pass through your dishwasher. Replace if cracked, worn, or missing to restore proper fit.
Seals the sump to maintain water pressure and spray effectiveness. Replace if you notice weak spray, poor cleaning, or leaks. Confirm fit with your model.
This kit is used to repair a leaking pump on GE made dishwashers. For a complete pump/motor assembly get WD26X10013.
Secures the dishwasher sump connection at the tub base for a leak-resistant seal. Replace if weakened or corroded to stop drips. Confirm fit with model.
Secures dishwasher sump to tub, maintaining seal compression to prevent leaks. Replace if corroded or weak. Confirm fit with your model number.
This is a genuine OEM replacement lower spray arm bearing sourced directly from the manufacturer for use in dishwashers. The lower spray arm spins to distribute water to the dishes during the wash cycle. Thus spray arm bearing supports the spray arm and lessens the friction, which allows it to spin more easily. If the dishes are not clean after the wash and rinse cycle, or the arm is making loud noises, the spin arm bearing may need to be replaced. This bearing is a small metal part that may wear over time. If the bearing is distorted or damaged, the arm will not sit level, and spinning may be very loud, or it may not spin. The spray arm bearing should be replaced. Turn off the breaker or disconnect the power to the dishwasher. Open the dishwasher and pull the bottom rack out. Turn the lower spray arm counterclockwise to remove it. Use a telescoping magnet to pull the bearing up from the hole in the middle. Install the new bearing and reinstall the spray arm. Put the dishrack back inside and reconnect the power.This lower spray arm bearing is a gray metal part that is sold individually. It is designed for use in dishwashers designed by General Electric and Hotpoint.
The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.
Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.
Symptoms of a bad Fine Filter Hub Nut include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Dishwasher leaking from underneath? A cracked pump connector causes water pooling. Requires dishwasher removal; typically 1-hour repair once accessed.
Sump plate that mounts at the bottom of the dishwasher tub assembly. Replace if cracked, warped, or damaged to restore proper structural support.
Replaces cracked, kinked, or chewed drain hose that carries wastewater from your dishwasher to household plumbing. Essential for proper drainage function.
Dishwasher leaking from bottom or not draining? The sump assembly collects and recirculates water. Moderately easy DIY repair from underneath.
Traps food particles during wash cycles to prevent recirculation and ensure spotless dishes. Replace if clogged or damaged. Confirm fit with your model.
Secures dishwasher drain or inlet hoses to fittings to prevent leaks and slipping. Replace when loose, corroded, or during hose installation. Verify fit.
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.