Parts for Kenmore 795.74077610 (79574077610, 795 74077610): Other Parts

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

A single mounting screw used to secure panels, brackets, or components in place so assemblies stay stable during normal appliance use. Simple replacement for stripped or missing fasteners. What it does:

• Secures panels, trim, brackets or interior components to prevent rattling or movement
• Restores proper fit and alignment after service or accidental damage
• Helps reattach parts removed during maintenance or part replacement
• Small, durable fastener designed for appliance interior mounting applications

• Use the correct screw driver or bit to avoid stripping the head
• Match screw length and thread engagement to the original location before tightening
• Tighten until snug—do not overtighten to avoid cracking plastic or damaging threads
• Disconnect power and follow appliance safety procedures before performing repairs

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

This is a replacement screw used to secure appliance panels, trim, and small components so damaged or missing fasteners don't leave parts loose. It restores proper fit and reduces rattling and movement. What it does:

• Secures panels, trim pieces, or internal components to restore proper fit
• Stops panels from shifting or vibrating during use
• Replaces stripped, corroded, or missing screws that prevent proper assembly
• Helps eliminate rattling noises caused by loose fasteners

• One replacement screw as pictured

• Unplug the appliance or shut off power before installing
• Use the correct screwdriver or bit to avoid stripping the head
• Hand-start the screw, then snug—do not overtighten to avoid cracking plastic parts
• If screw threads are damaged, replace with the exact OEM screw to ensure proper fit

This customized screw secures internal or external appliance components to restore proper fit and reduce movement. Use it to replace missing or damaged fasteners so panels and assemblies stay firmly attached during normal operation. What it does:

• Fastens panels, brackets, or small assemblies to maintain structural stability
• Prevents rattling, vibration noise, or loose trim caused by missing screws
• Restores correct alignment where a stripped or damaged screw allowed movement
• Works as a direct replacement for the matching screw specified for the repair

• One screw

• Disconnect power and water supply before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten to prevent thread damage
• Keep small parts away from children and retain any removed hardware for reuse if needed

This replacement door handle restores a secure grip and proper door operation on compatible refrigerators. Durable and contoured to match factory styling, it replaces cracked, loose, or broken handles for a safer, finished look. What it does:

• Provides a firm, ergonomic grip to open and close the refrigerator door
• Replaces cracked, damaged, or loose handles that affect door usability
• Restores the appliance's factory appearance and user comfort
• Helps prevent further damage from using a compromised handle

• Power off and unplug the appliance or disconnect power at the breaker before installation to avoid electrical risk
• Use appropriate hand tools; support the door during removal/installation to prevent injury or damage
• Follow the manufacturer service manual or on-page model fitment for proper screw locations and torque

This drain tube assembly channels defrost water from the evaporator to the drain pan, preventing leaks and water buildup. Replace a cracked or clogged tube to restore proper drainage and reduce puddles or ice inside your refrigerator.

• Directs defrost water from the drain outlet to the drain pan
• Helps prevent water leaks inside the fresh food or freezer compartment
• Addresses issues from a tube that is cracked, kinked, or obstructed by debris/ice
• Common symptoms: water under crisper drawers, puddles beneath the unit, or ice forming at the freezer bottom

• Unplug the refrigerator before servicing
• Access the drain outlet and remove any ice or debris from the drain path
• Fully seat the tube at both ends to ensure a secure, leak-free fit
• Test by pouring a small amount of warm water into the drain to confirm proper flow to the pan

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This DC motor assembly replaces the appliance's main DC drive motor to restore reliable motor-powered operation. It provides the exact-fit motor needed to regain normal mechanical function and reduce downtime. What it does:

• Drives the appliance's motorized components so the unit can run as intended
• Stops motor-related failures like no-spin, no-run, or intermittent operation
• Helps resolve motor humming or erratic movement when the motor is the cause
• Works with the appliance's existing mounting and electrical connections when compatible

• Disconnect power before servicing to avoid shock or injury
• Replacement typically requires removing panels and disconnecting electrical connectors—keep track of fasteners
• Inspect wiring harness and connectors for damage before reassembly

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

The Freezer Tray is an OEM part for LG refrigerators. It provides a convenient and organized space for storing frozen foods, ensuring they remain easily accessible and properly arranged within the freezer compartment.

Causes of a bad freezer tray can include cracks or breaks from heavy items, warping due to temperature fluctuations, or general wear from frequent use. A damaged tray can lead to improper storage and difficulty in organizing frozen items.

Symptoms of a bad freezer tray include:

• Cracks or splits in the tray
• Difficulty sliding the tray in and out
• Warping or bending
• Reduced storage capacity

This OEM LG part is also compatible with Sears/Kenmore.

This drawer tray assembly forms the shelf/base that supports a slide-out bin inside the refrigerator. Replace a cracked or warped tray to restore stable food storage and smooth drawer movement.

• Supports a slide-out drawer and food items in the fresh food or freezer section
• Helps drawers track correctly and sit level
• Damage can lead to binding drawers, tilting contents, or reduced storage
• Common signs: cracked plastic, sagging tray, drawer hard to open/close, visible wear

• Disconnect power and remove food from the affected area
• Slide out and remove the drawer(s) resting on the tray
• Lift out the damaged tray; transfer any reusable trim from the original if applicable
• Seat the new tray fully in the supports and reinstall the drawer(s)

The Tray Assembly Drawer is an OEM part for LG refrigerators. This tray assembly provides organized storage space in the freezer section, making it easier to access and manage frozen items.

Over time, freezer tray assemblies can become damaged due to regular use, accidental impacts, or overloading with heavy items. Damage can also occur if the drawer is forced open or closed when obstructed.

Symptoms of a bad freezer tray assembly include:

• Difficulty sliding the drawer in and out
• Cracks or breakage in the tray or its components
• Items not staying securely in place within the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

The Tray Assembly Drawer is an OEM part for LG refrigerators. This tray assembly provides organized storage space in the freezer section, making it easier to access and manage frozen items.

Over time, freezer tray assemblies can become damaged due to regular use, accidental impacts, or overloading with heavy items. Damage can also occur if the drawer is forced open or closed when obstructed.

Symptoms of a bad freezer tray assembly include:

• Difficulty sliding the drawer in and out
• Cracks or breakage in the tray or its components
• Items not staying securely in place within the drawer

This OEM LG part is also compatible with Sears/Kenmore models.

The Freezer Tray is an OEM part for LG refrigerators. It provides a convenient and organized space for storing frozen foods, ensuring they remain easily accessible and properly arranged within the freezer compartment.

Causes of a bad freezer tray can include cracks or breaks from heavy items, warping due to temperature fluctuations, or general wear from frequent use. A damaged tray can lead to improper storage and difficulty in organizing frozen items.

Symptoms of a bad freezer tray include:

• Cracks or splits in the tray
• Difficulty sliding the tray in and out
• Warping or bending
• Reduced storage capacity

This OEM LG part is also compatible with Sears/Kenmore.

This shelf net is a replacement mesh shelf for refrigerators that helps keep bottles and small items secured and organized on a fridge shelf. Restores containment for torn or sagging nets. What it does:

• Provides a flexible mesh surface to hold bottles, cans and other items in place
• Prevents small items from falling through or shifting during door access
• Replaces torn, stretched or sagging shelf nets that no longer secure contents
• Helps restore original shelf function and appearance

• Disconnect power or unplug the refrigerator before starting any repair
• Remove food and the affected shelf before replacing the net
• Typically installs by fitting the net into the dedicated shelf frame or clips; for exact instructions
• Wear gloves to avoid sharp edges on shelf frames during installation

The Crisper Glass is an OEM part for LG refrigerators. This glass panel sits on top of the crisper drawers, providing a clear view of the contents inside while supporting the items placed on top. It helps in maintaining the structural integrity of the crisper area and aids in the efficient organization of food items.

Causes of a bad crisper glass can include accidental dropping, heavy impact, or overloading the shelf beyond its weight capacity. A damaged crisper glass can compromise the safety and usability of the crisper drawers.

Symptoms of a bad crisper glass include:

• Cracks or chips in the glass
• The glass panel not fitting securely or evenly
• Difficulty in sliding the crisper drawers
• Potential risk of glass shards in the refrigerator

This OEM LG part is also compatible with Sears/Kenmore models.

This refrigerator glass shelf assembly replaces a broken, cracked or missing interior shelf so you can safely store food and restore usable shelving space. Tempered glass shelf with frame supports everyday fridge organization. What it does:

• Provides a stable, easy-to-clean surface for storing food and containers
• Replaces cracked, chipped or shattered glass shelves that cause leaks or safety hazards
• Prevents items from falling through open shelf openings and helps maintain internal organization
• Fits into existing shelf rails and rests on factory shelf supports

• Disconnect power and remove food before installing to avoid spills and injury
• Handle tempered glass carefully; wear gloves to protect hands during installation
• Slide shelf into existing rails until it seats securely on factory supports
• If shelf support clips or rails are damaged, replace them before installing this shelf

This rail holder is a small replacement mounting clip that secures a rail or guide in place so racks or sliding components stay aligned and operate smoothly. It restores proper fit and reduces shifting or rattling during use. What it does:

• Secures the appliance rail or guide to prevent the rail from coming loose
• Keeps racks or sliding parts aligned for smooth movement
• Reduces vibration and rattling caused by a loose rail
• Helps prevent minor wear from misalignment or shifting components

• Disconnect power (or unplug) and remove any obstructing parts before replacing the holder
• Replacement typically requires basic hand tools; retain all fasteners and note orientation
• Inspect mating rail and fasteners for damage; replace any worn parts to ensure a secure fit

This fresh room tray assembly restores the dedicated deli/snack drawer in your refrigerator. Replace a cracked, warped, or missing bin to keep foods organized and ensure smooth, reliable access.

• Provides a smooth-sliding storage bin for deli/snack items in the fresh food section
• Restores organization and usable space when the original tray is broken or missing
• Fits on the existing fresh-room rails/shelf designed for this drawer
• Symptoms it can resolve: cracked or broken tray, hard-to-slide drawer, missing bin

• Open the refrigerator and clear the area around the drawer location.
• Pull the old tray straight out; lift or tilt to clear the stops as your model requires.
• Align the new tray with the side rails and slide it in until fully seated.
• Handle plastic carefully to avoid damage; do not force the drawer.

The Slide Rail is an OEM part for LG refrigerators. This part allows the smooth and stable operation of the freezer drawer, allowing it to slide in and out. The slide rail supports the weight of the drawer and its contents, facilitating easy access to frozen items while maintaining proper alignment. The rail measures approximately 16” x 2”

Causes of a bad slide rail can include wear and tear from frequent use, physical damage from overloading the drawer, and the accumulation of debris or ice buildup that can obstruct the sliding mechanism.

Symptoms of a bad slide rail for the freezer drawer include:

• Difficulty in sliding the freezer drawer in and out
• The freezer drawer not staying in place or coming off the rails
• Unusual noises such as grinding or squeaking during movement
• Visible damage, bending, or rust on the rail

This OEM LG part is also compatible with some Kenmore models.

The Rail Guide Assembly is an OEM replacement part for LG bottom-mount refrigerators. It contains telescopic extension rails and channel brackets that accommodatingly glide freezer and fridge shelves in and out with simplicity. This assembly facilitates effortless access to every stored item.

Causes of part malfunction relate to prolonged retraction/extension stressing roller bearings and metal rails to the point of fatigue cracks or binding issues hindering smooth sliding.

Symptoms involve:

• Shelves that resist extension or fail to fully retract into fridge cavities
• Grating noises and vibrations emerging from misaligned or strained rails
• Inconvenient access as capacity-flexible shelving gets restricted

This OEM replacement part is compatible with LG and Kenmore bottom-mount refrigerators.

The Freezer Drawer Rail Assembly is an OEM part for LG refrigerators. This assembly includes the rails that support and guide the freezer drawer, allowing it to slide in and out smoothly for easy access to frozen foods.

Causes of a bad freezer drawer rail assembly can include wear and tear over time, buildup of ice or debris, or damage from excessive force or impact. A compromised rail assembly can hinder the drawer's movement and affect the overall functionality of the freezer.

Symptoms of a bad Freezer Drawer Rail Assembly include:

• Difficulty opening or closing the freezer drawer
• The drawer not staying aligned or on track
• Unusual noises when operating the drawer
• Visible damage or wear on the rails

This OEM LG part is also compatible with Sears/Kenmore.

This right-side Freezer Basket Support Rail is an OEM part for LG refrigerators. Located inside the freezer compartment, it provides elevated storage shelves for ice cream, frozen vegetables, meats, and more above the freezer floor.

Causes of a bad support rail can include damages such as cracks or breaks that compromise its load-bearing ability over years of use. Sharp freezer temperatures cause constant contraction and expansion.

Symptoms of a bad support rail include:

• Baskets or containers unstable and prone to tipping
• Reduced storage capacity within the freezer
• Safety concerns if a cracked rail were to fully collapse

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Freezer Basket Support Rail is an OEM part for LG refrigerators. This component is essential for supporting and guiding the freezer basket, allowing it to slide in and out smoothly. The rail measures approximately 13 x 2 inches.

Symptoms of a failing Freezer Basket Support Rail include:

• Difficulty sliding the freezer basket in and out
• Unusual noises such as grinding or squeaking when moving the basket
• The basket becoming misaligned or tilting when pulled
• Visible wear or damage to the rail

Causes of a bad support rail often include mechanical stress from overloading the basket, frequent use which can wear down the material, or accidental damage during cleaning or rearranging items within the freezer.

This OEM LG part is also compatible with Sears/Kenmore.

This holder assembly bracket secures and aligns a small appliance component so it stays in place during normal use, restoring reliable fit and reducing noise or movement caused by a loose part. What it does

• Provides a stable mounting point for the associated component to prevent shifting or detachment
• Restores correct alignment for doors, panels, or internal modules that rely on the bracket
• Helps stop rattling, vibration noise, or intermittent contact caused by a broken or bent bracket
• Supports safe operation by keeping parts properly positioned within the appliance

• Basic hand tools are usually all that's required; follow the appliance service manual for access steps
• Disconnect power (and water, if applicable) before starting any repairs to avoid shock or injury
• Inspect adjacent fasteners and mounting surfaces; replace any stripped screws or damaged clips for a secure fit

This tray cover assembly replaces a cracked or warped cover that supports the refrigerator bin/tray. Restoring a level, secure surface helps keep items stable and allows the drawer to move and seat properly. What it does:

• Forms the shelf/cover above a refrigerator drawer or tray
• Supports items stored above and aligns the bin beneath
• Replaces cracked, sagging, or broken frames and tabs
• Helps prevent spills and binding when opening or closing the drawer

• Includes 1 tray cover assembly

• Unplug the refrigerator and clear the compartment for safe access.
• Slide out and remove the bin/tray; lift the old cover off its support rails or tabs.
• Position the new cover; ensure all tabs fully engage before reinstalling the bin and checking movement.

This vegetable tray is the molded crisper cover that supports produce and separates the fresh-food compartment. Restores a stable shelf surface for drawers and keeps fruits and vegetables organized. What it does:

• Provides a flat, durable shelf above the crisper drawer so produce sits evenly
• Helps contain spills and prevents items in the drawer from pushing up into upper shelves
• Replaces cracked, warped or missing tray that can cause unstable storage
• Fits into the refrigerator's drawer area and supports normal storage loads

• Remove all food from the drawer area before installing to avoid spills
• Install by sliding the tray into the drawer rails or resting it on the shelf supports until it clicks into place
• Do not force the tray; inspect rails/guides for damage and replace if worn
• Clean with mild detergent and water; avoid abrasive cleaners or high heat

This vegetable tray is the removable crisper bin insert that organizes and stores fresh produce in the refrigerator, keeping fruits and vegetables contained and easy to access. Durable plastic construction fits into the crisper area. What it does:

• Provides a dedicated storage bin for produce to keep items organized and prevent rolling or bruising
• Helps contain spills and keeps messes confined to the tray for easier cleanup
• Restores a missing, cracked, or warped crisper surface that can affect storage capacity
• Fits into the refrigerator's crisper compartment to maintain usable shelf space

• Remove any food and empty adjacent bins before installing to avoid spills
• Slide the tray into the crisper compartment until it seats fully; no tools required for typical installs
• If the tray is cracked, discard damaged pieces to avoid contamination of stored food
• Keep away from open flames and high heat to prevent warping

This cover assembly is the molded trim panel labeled "TV" in the manufacturer's parts list. It replaces a cracked or missing cover to shield internal components and restore a secure fit and finished appearance.

• Provides a protective, finished cover for the designated opening/section
• Shields internal components from dust and accidental contact
• Restores secure mounting when the original cover is cracked, warped, or missing
• Can help reduce rattling or vibration noise caused by a loose/damaged cover

• Disconnect power to the appliance before servicing
• Access the cover location; remove screws or carefully release locking tabs
• Transfer any reusable inserts or hardware from the original if present
• Align the new cover, fully engage tabs, and reinstall screws without overtightening

This guide assembly secures and aligns internal components in the TV cabinet to restore proper panel alignment and stable fit. Replacing a worn or damaged guide helps reduce cabinet gaps and prevents rubbing or misalignment. What it does:

• Positions and supports internal TV components and the front cabinet for correct alignment
• Keeps the panel or chassis from shifting or rubbing against the cabinet
• Helps eliminate loose or uneven gaps around the display caused by a damaged guide
• Restores secure mounting where the original guide has cracked, worn, or broken

• One guide assembly as shown

• Unplug the TV and place it on a soft, flat surface before starting
• Remove cabinet screws or trim panels carefully to access the guide mounting area
• Match the replacement guide to the original orientation; reinstall hardware to manufacturer torque if specified

This rail guide assembly supports and aligns a refrigerator drawer so it slides smoothly along its track. Replacing a worn rail restores easy operation and helps prevent binding, sagging, or uneven travel when opening and closing.

• Supports and guides the drawer/bin along the cabinet track
• Helps the drawer open and close smoothly and stay level
• Maintains proper alignment so the drawer seats correctly
• Common symptoms: drawer hard to slide, tilts or binds, rough/noisy travel, visible cracks or damage on the rail

• Disconnect power and remove drawer contents for safety
• Pull out and lift the drawer/basket off the rails to access the mounting points
• Remove screws/clips, transfer any brackets or end caps from the old rail, and install the new assembly
• Re-engage the drawer on both rails and test for smooth operation before reloading

The Crisper Drawer Slide Rail is an OEM part for LG refrigerators. It is designed to support and guide the crisper drawer, allowing it to slide in and out smoothly for easy access to your fresh produce. The rail measures approximately 20 x 6 inches,

Over time, the slide rail can wear out or become damaged, affecting the operation of the crisper drawer. Common causes of a bad crisper drawer slide rail include repeated use, accidental impact, or the accumulation of debris and residue that can hinder movement.

Symptoms of a bad crisper drawer slide rail include:

• Difficulty sliding the crisper drawer in and out
• The drawer not staying securely in place
• Unusual noises when using the drawer
• The drawer becoming misaligned or falling out of the track

This OEM LG part is also compatible with Sears/Kenmore models.

This case assembly is the outer housing for the Magic Room compartment, restoring proper fit and protection for internal components. Replaces a cracked, warped or damaged compartment case to help maintain compartment integrity and appearance. What it does:

• Provides the structural housing for the Magic Room compartment and secures internal components
• Restores proper alignment and fit to prevent rubbing or interference with doors/drawers
• Helps maintain an even internal compartment environment by sealing the compartment area
• Addresses visible damage such as cracks, broken mounting tabs or deformation

• Refer to the refrigerator's service manual for disassembly/reassembly steps and proper fastener torque
• Disconnect power to the appliance before starting any repair to avoid electrical hazard
• Handle plastic components carefully to avoid further cracking; replace any broken mounting clips
• Replace damaged screws or brackets with OEM-specified hardware for a secure fit

The Door Gasket is an OEM part for LG refrigerators. It serves as a thermally-insulating boundary around the freezer door helping maintain intended sub-freezing temperatures.

Causes of a bad freezer door gasket can involve hardening of the rubber from prolonged exposure to freezer climate conditions. Mineral accumulation aggravates inflexibility over time as well.

Symptoms of a bad freezer door gasket include:

• Difficulty closing the freezer door fully or securely
• Reduced energy efficiency from cold air escape
• Premature evaporation of the door seals' adhesive
• Gap formation around the door exposing food to warmer air

This OEM LG part is also compatible with some Kenmore models.

This hinge cap covers and protects the door hinge, keeping the hinge assembly clean and improving the appliance's appearance. It replaces a cracked, missing, or worn hinge cover to help doors operate smoothly and look finished. What it does:

• Covers the door hinge to protect mating surfaces from dirt and damage
• Hides hinge hardware for a cleaner, finished look
• Helps prevent debris from interfering with hinge movement
• Can resolve cosmetic issues and reduce risk of snagging on exposed hinge parts

• One hinge cap

• Remove power and open the door to a safe, supported position before starting
• Typically snaps or screws onto the hinge—retain original fasteners unless replacement required
• Inspect hinge and fasteners while installing; replace any damaged hardware

This door gasket assembly seals the refrigerator door to help maintain proper internal temperature and reduce energy loss. Replacing a worn or torn gasket restores a tight seal for better cooling and food preservation. What it does:

• Forms an airtight seal between the refrigerator door and cabinet to limit warm air entry
• Helps prevent frost buildup and condensation that can occur with a failing seal
• Reduces compressor run time caused by air leaks, improving cooling consistency
• Commonly replaced when gasket is torn, deformed, hard, or no longer seats properly

• Disconnect power to the appliance before starting any repair.
• Inspect the door edge and mounting channel; remove any debris before seating the new gasket.
• Warm the gasket slightly if needed to help it seat; avoid open flames or overheating.
• Verify even seating around the entire door and check door alignment; run a paper test to confirm a consistent seal.

Door gasket assembly provides a secure, flexible seal around the appliance door to prevent leaks and maintain proper internal conditions. Replacing a torn or worn gasket restores sealing performance and reduces leaks, drafts, or temperature loss. What it does:

• Forms the primary seal around the door to keep water, air, and temperature inside the appliance.
• Stops visible leaks or pooling around the door opening.
• Helps prevent temperature fluctuations, frost buildup, or loss of cleaning/drying performance caused by a poor seal.
• Addresses visible damage symptoms such as cracks, tears, deformation, or persistent odors around the door edge.

• Always disconnect power (and water, if applicable) before starting any repair.
• Remove the old gasket carefully; inspect and clean the door channel and mounting surface before installing the new gasket.
• Ensure the replacement gasket is fully seated and any retaining clips or fasteners are secured per OEM instructions; test the door for proper fit and sealing.

This replacement gasket seals the Home Bar (door-in-door) access panel on your refrigerator. A fresh, flexible seal stops warm-air leaks that cause condensation, frost, and temperature fluctuations, helping the unit run efficiently and keep food cold.

• Forms an airtight seal around the Home Bar/door-in-door panel
• Helps maintain proper interior temperature and humidity
• Common symptoms: visible gaps, torn or warped gasket, condensation or frost near the panel, door not closing flush
• Restores reliable closing and reduces unwanted airflow

• Disconnect power before servicing
• Open the Home Bar panel, pull the old gasket from the channel, then align and press the new gasket fully into the groove—seat corners first
• Warm the gasket (hair dryer on low or soak in warm water) to relax folds; do not overheat
• Close and check for an even seal; adjust by massaging the gasket into place as needed

This drawer guide is the sliding rail that helps a refrigerator/freezer drawer open and close smoothly and stay aligned. It restores stable drawer movement and prevents sticking, sagging, or drawers coming off the track. What it does:

• Guides and supports the drawer as it slides in and out
• Keeps the drawer aligned to prevent binding or uneven movement
• Reduces drawer sag and helps prevent accidental removal
• Restores smooth operation when original guide is cracked, worn, or broken

• One drawer guide

• Disconnect power to the appliance before starting any repair
• Remove the drawer per the appliance service instructions to access the guide
• Replace the guide using the OEM fasteners or clips; keep original mounting hardware unless damaged

Replacement door basket that restores convenient storage on the appliance door, keeping bottles and small items secure and accessible. Replaces damaged or missing door bins to help keep your appliance door organized and usable. What it does:

• Provides a secure shelf on the appliance door for bottles, condiments and small containers.
• Replaces cracked, chipped or broken door bins that no longer hold items safely.
• Restores lost or reduced door storage capacity for easier organization.
• Helps prevent items from falling out of the door during normal use.

• Disconnect power (unplug or switch off) and remove all items from the door before starting.
• Most installations are hand-operated: lift or tilt the old bin out of the door track, then seat the replacement into the same track—do not force.
• Inspect mounting clips or supports during replacement; damaged clips must be replaced separately.

This cover lever replaces a damaged or worn dispenser lever cover to restore a clean, functional surface for pressing the dispenser. Helps keep debris out of the lever area and supports reliable lever actuation. What it does:

• Covers and protects the dispenser lever mechanism from chips, cracks, and debris.
• Provides a smooth contact surface for pressing the dispenser to activate water/ice dispensing.
• Helps prevent leaks or improper actuation caused by broken or warped lever covers.
• Restores cosmetic appearance at the dispenser area when the original cover is cracked or missing.

• Disconnect power and shut off the water supply before beginning any work.
• Removal typically requires accessing the dispenser bezel or door panel—use basic hand tools and retain all fasteners.
• Handle clips and tabs carefully to avoid breakage; test dispenser function after reassembly.

The Basket Assembly is an OEM component specifically designed for LG Door-in-Door refrigerators containing bottom-mounted crisper drawers. This integral assembly organizes stored items within the refrigerator doorway.

Symptoms of a bad basket assembly include:

• Cracked or broken perforated shelves  
• Detached mounting brackets failing to secure basket
• Warped contours no longer fitting base compartment
• Missing attachments inhibiting proper installation

Causes of failure involve stresses from repeated loading/unloading cycles, mineral buildup weakening plastic brackets over time, or impact damage compromising structural integrity.

Replace yours today with this genuine OEM LG assembly to maintain tidy organizational capacity. Precision slots provide adjustable shelf positioning optimized for produce, snacks, and beverages. Compatible across Samsung, Frigidaire, and GE models featuring removable door crisper baskets.

This is a refrigerator door basket that mounts on the inner door liner to hold bottles, condiments, and other small items. Replacing a damaged bin restores secure storage and helps keep items organized and accessible.

• Provides on-door storage space for beverages and condiments
• Helps keep items from tipping or falling when the door opens
• Replace if cracked, broken, warped, or no longer stays seated in the door slots
• Common signs include the bin falling off, visible cracks, or reduced capacity

• Unplug the refrigerator for safety before replacing interior parts
• Lift the old bin up and out of the door liner slots
• Align and press the new bin straight into the slots until fully seated
• Do not overload; distribute weight evenly to prevent future damage

The Refrigerator Door Shelf is an OEM part for LG refrigerators. It provides additional storage space on the door of the refrigerator, allowing for the organization and easy access of frequently used items such as condiments, beverages, and small containers. It measures approximately 14" x 4" x 4".

Causes of a bad refrigerator door shelf can include general wear and tear from repeated use, overloading the shelf with heavy items, or accidental damage during cleaning or reorganization. Cracks or breakage in the plastic material can also render the shelf unusable.

Symptoms of a bad refrigerator door shelf include:

• Cracked or broken shelf
• Items not staying securely on the shelf
• The shelf not fitting properly into the door brackets
• Difficulty in attaching or removing the shelf

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This lower hinge assembly secures and supports the refrigerator/freezer door at its bottom pivot, restoring proper door alignment and smooth opening. Replaces a worn or damaged hinge to help reduce sagging, rubbing, or uneven sealing. What it does:

• Provides the pivot point and mounting for the bottom of the appliance door.
• Restores correct door alignment to improve door closure and sealing.
• Helps eliminate door sag, binding, or scraping during operation.
• Durable molded/metal construction built to match OEM fit and function.

• Disconnect power and empty/secure the door before starting; prop or support the door to prevent dropping.
• Keep fasteners and alignment shims used during removal for reference; transfer any hardware only if explicitly required.
• Use basic hand tools; follow the appliance service manual for torque and alignment instructions.

This bushing is a replacement shaft support that stabilizes a rotating assembly and helps reduce wear and noise. It restores smooth movement and helps maintain proper alignment for the appliance component. What it does

• Supports and centers a rotating shaft or drum to reduce wobble and rubbing
• Reduces noise and friction from worn pivot or support points
• Helps prevent uneven wear on mating parts and prolongs assembly life
• Commonly replaced when you hear squeaking, grinding, or notice excessive play

• One bushing

• Inspect mating surfaces and replace any damaged clips, seals, or fasteners as needed
• Use basic hand tools; hold the assembly steady and press the bushing squarely into place
• If the bushing is press-fit, use a suitable driver or press to avoid damage
• Disconnect power and follow all safety precautions before beginning repairs

This door stopper mounts at the hinge to limit the refrigerator door's opening angle and provide a positive stop. Replacing a worn stopper helps protect the hinge, prevent over-swing, and promote a smooth, even door seal.

• Limits door opening at the hinge to prevent overextension
• Helps maintain door alignment and consistent gasket contact
• Reduces impact that can loosen hinges or damage the cabinet
• Common symptoms: door swings too far, clunks at full open, doesn't stop smoothly, or shows visible wear at the stop

• Disconnect power and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners as needed to access the stopper
• Install the new stopper in the same orientation; tighten hardware securely
• Verify door swing and sealing after reassembly

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

This slide rail lets a drawer move smoothly in and out, restoring proper alignment and stable operation. Replace a worn or bent rail to stop sticking, uneven travel, or a drawer that comes off its track. What it does:

• Guides the drawer along its track for smooth opening and closing
• Restores even, stable travel and prevents the drawer from catching or binding
• Replaces bent, worn, or damaged rail components that cause misalignment
• Helps keep the drawer aligned to prevent tilting or partial ejection

• One slide rail

• Disconnect power and remove the drawer before replacing the rail when applicable
• Verify rail orientation and slide fully into the track before securing fasteners
• Use basic hand tools; keep removed screws and clips for reinstallation
• If the drawer is heavy, have a second person assist to prevent injury or damage

This guide assembly rail is the replacement drawer slide that restores smooth, stable movement for a refrigerator or appliance drawer. It keeps the drawer aligned and reduces sticking or uneven operation for everyday use. What it does:

• Guides and supports the drawer as it opens and closes to maintain proper alignment.
• Reduces sticking, scraping, and uneven travel caused by worn or damaged rails.
• Helps prevent drawer sagging and improves load stability when pulling out the drawer.
• Works with the factory mounting points and keeps the drawer tracking true.

• One guide assembly rail.

• Disconnect power or follow appliance-specific safety procedures before servicing.
• Remove the drawer or access panel to reach the existing rail; keep fasteners for reuse unless replacement required.
• Compare the new rail to the old part to ensure fit and orientation before installing.
• If fasteners are damaged or missing, replace with OEM-specified hardware.

This guide assembly keeps a sliding appliance drawer or rack aligned for smooth, reliable movement and helps prevent sagging or derailment. It restores proper tracking so the drawer/rack opens and closes without binding. What it does:

• Guides and supports a sliding drawer or rack so it stays aligned during use
• Reduces binding, sagging, or derailment when loading or pulling the drawer/rack
• Eliminates scraping or grinding noises caused by a worn guide
• Helps restore smooth, even motion and proper engagement with the slide mechanism

• One guide assembly

• Disconnect power before starting any repair
• Remove the affected drawer/rack to access the guide; keep track of fasteners
• Align the guide with the slide channel and secure per the OEM fastening points; some designs snap in while others use screws
• If mounting hardware is worn or missing, replace with OEM-specified fasteners for safe operation

This replacement hinge assembly supports and pivots the refrigerator door. Replacing a worn or bent hinge restores smooth door movement and proper alignment so the gasket can seal correctly to help maintain performance. What it does:

• Provides the pivot point for the door to open and close
• Supports the door's weight to keep it aligned
• Helps the door gasket seal evenly against the cabinet
• May correct issues such as door sagging, rubbing, popping, or not closing/sealing fully

• One hinge assembly

• Unplug the refrigerator and remove items from the affected door
• Support the door while removing hinge screws; note the orientation of any spacers/bushings
• Transfer any reusable hardware from the old hinge to the new assembly
• Reinstall and tighten fasteners; verify door is level and check gasket seal

The Freezer Drawer Rail is an OEM component for select LG refrigerators.  Its operatation allows access to frozen foods.  

Causes of a bad rail could include debris accumulation, ice buildup, or physical damage that hinders smooth sliding. Over time, continuous usage may also cause wear of moving parts.

Symptoms of a failed freezer drawer rail include: 

• Resistance or stiffness when opening/closing drawers
• Noisy, squeaking, or grinding sounds  
• Drawers that do not fully extend or retract
• Drawers detaching from the rail mechanism

This OEM LG rail is compatible with LG and Kenmore French door refrigerator models.

The Freezer Drawer Rail is an OEM component for LG French door refrigerators featuring bottom drawer designs. It provides smooth gliding support for the refrigerator's lower freezer storage compartment.

Common causes involve typical fatigue damage concentrating stresses at sensitive drawer guide interfaces.

Symptoms include:

• Drawer difficult to fully extend or retract
• Noises or binding during operation 
• Reduced storage organization from impaired drawer support

This OEM LG part can also be used on Kenmore/Sears appliances.

This ice maker drive gear engages the ice maker's motor to rotate the ejector and harvest ice, restoring proper ice release and ejection. Ideal for common ice-maker failures where the tray doesn't cycle. What it does:

• Transfers motor torque to the ice ejector, allowing the ice maker to harvest and eject cubes
• Commonly used when the ice maker stops cycling or fails to eject ice
• Can reduce grinding or clicking noises if the original gear is stripped or worn
• Works with the ice maker's harvest and fill sequence to maintain normal operation

• Power off and unplug the refrigerator before beginning service
• Remove the ice maker assembly per manufacturer instructions to access the gear
• Inspect mating gears and motor shaft for wear; replace any damaged parts to prevent repeat failure

This supporter hinge is the OEM-style hinge support that helps secure and align the appliance door, restoring stable door movement and proper sealing. Built to match the original hinge geometry for reliable fit. What it does:

• Supports the door at the hinge mounting point to keep door alignment stable
• Helps prevent sagging or uneven door gaps that can cause poor sealing
• Restores smooth opening and closing when worn or damaged hinge support is the cause
• Works as the hinge mounting support component shown in OEM parts diagrams

• One supporter hinge

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Follow the appliance's service manual for disassembly order and hinge removal/installation steps
• Use common hand tools (screwdriver, socket) and keep fasteners organized for reassembly
• Check adjacent hinge components and mounting hardware

This center hinge assembly replaces the middle door hinge on compatible French-door refrigerators to restore proper door alignment and smooth opening. It helps prevent sagging, binding, and air leaks caused by a worn or damaged hinge. What it does:

• Supports and aligns the upper/lower refrigerator doors for correct sealing
• Enables smooth pivoting of the door to open and close without binding
• Corrects uneven gaps or door sag that can cause cooling loss or excessive wear
• Replaces a bent, cracked, or worn hinge that may cause noisy operation

• One center hinge assembly

• Remove power and empty the door(s) before beginning work; follow manufacturer service instructions
• Use proper tools and support the door while removing/installing the hinge to avoid injury or damage
• Inspect surrounding trim and fasteners; replace any worn screws or bushings as needed

This center hinge assembly replaces the factory door pivot and restores proper door alignment and smooth opening. It supports the refrigerator door at the center hinge point to help stop sagging, binding, or uneven gaps. What it does:

• Replaces the center pivot point that supports and guides the door
• Restores correct door alignment and even sealing to help maintain cooling efficiency
• Reduces door sag, sticking, and noise caused by worn hinge parts
• Allows the door to open and close smoothly when operating normally

• Disconnect power to the appliance and remove food from affected door before starting.
• Support or remove the door to avoid injury or damage; the door can be heavy.
• Use appropriate hand tools and follow torque guidelines in the OEM instructions.

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This tension spring provides the restoring force for a moving component in select LG appliances, helping doors or internal mechanisms return to their resting position and maintain correct alignment. It's a small mechanical part that restores motion reliably when functioning. What it does

• Supplies tension to return or hold a moving part (door, hinge or internal linkage) in its intended position
• Restores smooth, consistent motion and helps prevent slamming or sagging caused by worn springs
• Common symptom: door or component does not return, feels loose, or has uneven movement
• Works as a direct-fit service part when the original spring has stretched, broken, or lost tension

• One spring (quantity: 1)

• Inspect the matching mounting points and hardware before installing; replace any damaged clips or pins
• Use care when removing/installing under tension; wear eye protection and follow safe-handling practices
• Only install the part in appliances that list the same part number/location; do not force mismatched parts

This upper hinge assembly supports the refrigerator door at the top, providing a smooth pivot and proper alignment. Replacing a worn hinge restores even gaps and a tight seal to help maintain consistent cooling performance.

• Supports the door's weight and provides the top pivot point
• Maintains alignment for correct gasket compression and a tight seal
• Helps the door open and close smoothly without rubbing or binding
• Common signs of wear: door sagging or misalignment, rubbing/clicking noises, and poor sealing or condensation around the gasket

• Unplug the refrigerator before servicing.
• Remove the top hinge cover; retain screws and any shims for reuse.
• Support the door with a helper while removing and installing the hinge.
• Position the new hinge, align the door, then tighten screws and verify smooth swing and full gasket contact all around.

This replacement lever spring restores tension to a lever-style mechanism so the lever returns and operates reliably. Use it when a worn spring causes the lever to stick, slip, or fail to engage properly. What it does

• Replaces the worn or weakened spring in a lever assembly to restore proper return tension
• Helps prevent the lever from sticking, slipping, or failing to stay engaged
• Restores consistent mechanical movement for reliable operation
• Reduces intermittent or flaky lever behavior caused by a damaged spring

• Disconnect power to the appliance before starting any repair
• Inspect the lever assembly and mounting points; replace only the spring explicitly listed
• Use appropriate hand tools and pliers; avoid overstretching the spring during installation

This lever spring is a small replacement tension spring that restores proper return and engagement for a lever assembly. It helps maintain reliable lever movement and secure latching where a worn or broken spring causes play or non-return. What it does:

• Provides return tension for a lever or latch assembly so the lever snaps back into place
• Helps maintain proper engagement of latch/actuator mechanisms
• Common remedy for a loose, sagging, or non-returning lever
• Works as a direct-fit replacement when the original lever spring is damaged or fatigued

• One replacement lever spring

• Disconnect power and/or unplug the appliance before starting any disassembly
• Handle small springs carefully; keep track of orientation and any retaining clips during removal
• Installation may require partial disassembly of the trim or latch assembly

This lever holder is the replacement mounting bracket that secures the door lever so the microwave door operates smoothly and reliably. It restores proper lever alignment to help the door latch and release as intended. What it does:

• Secures the door lever assembly so the door can latch and release properly
• Keeps the lever aligned to prevent binding, sticking, or loose movement
• Helps restore normal door operation and user access to the oven cavity
• Common symptom: door feels loose, lever moves freely, or door will not latch

• Disconnect power before beginning any repair to avoid shock or injury
• Remove the outer cabinet or door trim only as needed to access the lever area
• Handle door components and glass carefully to avoid damage or injury

This replacement spring restores proper tension to a microwave oven door hinge so the door opens and closes smoothly and holds position. It's a direct-fit part that helps eliminate sagging or uneven door movement. What it does

• Replaces a worn or broken hinge spring to restore proper door tension and alignment
• Helps prevent door from dropping open or not staying closed securely
• Supports smooth, controlled door opening and closing motions
• Addresses symptoms such as a sagging door, uneven closing, or loose-feeling hinge

• One replacement hinge spring (quantity: 1)

• Disconnect power to the appliance before attempting any service to avoid electrical shock
• Access may require removing the outer door panel or control panel; follow OEM disassembly instructions
• Handle the spring carefully—springs can be under tension and may release suddenly

This funnel directs dispensed water or ice from the appliance's dispenser into your cup or container to reduce spills and ensure proper flow. It replaces a worn, cracked, or misaligned chute to restore clean dispensing. What it does:

• Guides water or ice from the dispenser to the user's cup or container
• Prevents drips and reduces splashing at the dispenser opening
• Helps position dispensed items so they clear the dispenser housing
• Addresses symptoms like leaking at the dispenser, uneven flow, or pieces falling inside the dispenser well

• One replacement funnel shown

• Disconnect power and water supply before starting any work
• Remove dispenser or front panel per your model's service instructions to access the funnel
• Align the funnel carefully with the mounting tabs and snap or fasten into place without forcing
• If clips or seals are damaged, replace them to ensure a secure, leak-free fit

This button assembly replaces the set of push buttons on the appliance control panel to restore reliable input and a finished appearance. Replaces worn, broken, or unresponsive control buttons so the unit accepts user commands correctly. What it does:

• Provides the user-facing push buttons used to select cycles, options, and start/stop functions
• Restores physical button action for hard-to-press, stuck, or missing buttons
• Helps resolve intermittent or non-responsive control inputs caused by damaged button hardware
• Maintains the original fit and appearance of the control panel

• One button assembly

• Disconnect power before beginning any repair
• Access typically requires removing the control console or top panel—keep fasteners and clips organized
• Handle the assembly carefully to avoid damaging plastic tabs or button contacts
• Test button operation before fully reassembling the console

This button assembly replaces a damaged or worn control-panel button cluster to restore reliable button response and user control. It fits into the appliance's console and provides the tactile interface needed to select cycles and settings. What it does

• Replaces the control-panel button cluster so unresponsive, stuck, or missing buttons can be fixed.
• Restores tactile feedback and reliable electrical contact for user inputs.
• Helps resolve intermittent or non-working button inputs when the switch/buttons are the cause.
• Matches the OEM form to fit into the factory console opening.

• Disconnect power (and water, if applicable) before starting any repair.
• Access typically requires removing the console or control panel.
• Handle the assembly and ribbon/contact connectors carefully to avoid damage.

This cover panel replaces a damaged or missing exterior trim piece to restore the appliance's appearance and protect internal components from dust and debris. It fits where the original cover was mounted and keeps wiring and parts shielded. What it does

• Covers and protects internal components from dirt and accidental contact
• Restores the appliance's exterior finish for a clean, finished look
• Helps reduce rattles by securing loose openings or edges
• Matches the original mounting locations for proper fit and alignment

• Disconnect power (unplug appliance or switch off breaker) before starting work.
• Removal/install typically requires basic tools (screwdriver or nut driver); keep original fasteners unless replacements are provided.
• Handle with care to avoid scratching the finish or breaking mounting tabs; avoid forcing clips.

This replacement hinge cover is a molded trim piece that snaps over the refrigerator door hinge to restore the appearance and protect the hinge area from dirt and damage. It keeps the hinge assembly concealed and the door looking finished. What it does:

• Covers and protects the door hinge assembly from dust, grease and accidental contact
• Restores a clean, finished look when original hinge cover is cracked, broken or missing
• Helps prevent debris buildup that can interfere with hinge movement
• Matches original mounting style for a secure snap-on fit when intact

• High-level replacement: typically snaps into place; inspect clips/tabs and align before pressing fully
• Power/disconnect: no electrical disconnect usually required, but follow appliance safety guidance and keep doors supported
• Handle gently to avoid breaking plastic clips during installation

This communication link module provides the refrigerator's control board with network and user-interface connectivity so features and diagnostics can be accessed and controlled. It helps restore lost app or panel communication. What it does:

• Handles communication between the refrigerator's control system and external interfaces (user panel, network app).
• Works with the main control electronics to transmit status and diagnostic information.
• Replaces a damaged or non-communicating module that prevents remote control or smart features.

• One link (communication) module.

• Disconnect power to the appliance before replacing this electronic module to avoid shock or damage.
• Handle the module by its edges and avoid touching circuit contacts.
• Installation typically involves removing an access panel and unplugging/reconnecting a wiring harness; keep track of screw and connector locations.

This damper assembly controls airflow between refrigerator compartments to help maintain set temperatures and even cooling. Replaces a failed or stuck damper to restore proper air distribution and temperature balance. What it does:

• Regulates airflow between compartments so cold air moves where needed
• Can stop stuck-open or stuck-closed airflow that causes uneven temperatures
• Often linked to symptoms like warm spots, inconsistent cooling, or temperature swings
• Help reduce excess frost or humidity issues caused by improper airflow

• Disconnect power to the appliance before starting any repair
• Access usually requires removing interior liners, shelves, or panels; follow the service manual
• Handle actuator and wiring carefully; avoid pinching wires when reinstalling

NOTE: This part also requires software update kit CJT30000002. DO NOT INSTALL WITHOUT UPDATING SOFTWARE. Call for more information.

This evaporator assembly is the sealed coil component that removes heat from the freezer section, helping maintain proper cold temperatures and consistent food preservation. It replaces a worn or damaged evaporator to restore effective cooling. What it does:

• Absorbs heat from inside the freezer compartment so the refrigerant can carry it away
• Supports proper airflow through the freezer evaporator compartment for consistent cooling
• Commonly used when the freezer is not reaching temperature or shows frost/freeze buildup on the evaporator area
• Works with the appliance's defrost system and refrigeration components to maintain correct operation

• Disconnect power before servicing; handle components carefully to avoid sharp fin injury
• Inspect surrounding gaskets, insulation, and mounting hardware during replacement and replace as needed
• Test defrost and fan operation after installation to confirm proper system function

The Thermistor Assembly, PTC is an OEM replacement part for LG refrigerator models. As a key sensor, the thermistor monitors and reports temperature levels inside fridge and freezer compartments to the main control board. It ensures optimal cooling through precise thermal feedback.

Causes of a bad thermistor can include failure to calibrate accurately due to age, loose connections disrupting readings, or external impacts compromising sensor integrity.  

Symptoms of a bad thermistor include:

• Abnormal or inconsistent temperatures within fridge sections  
• Compressor and fans cycling on and off too frequently
• Error codes relating to temperature display
• Inability of the control board to read temperature values

This OEM LG part is also compatible with Sears/Kenmore. Replacing a faulty thermistor restores exact temperature control for safe, long-lasting food storage.

The Overload Compressor is an OEM part for LG refrigerators. This part protects the refrigerator's compressor from overheating and potential damage by acting as a safety device. It works by monitoring the compressor's electrical current and temperature. If the compressor operates under conditions that could lead to overheating or overcurrent, the overload protector will cut off the power to the compressor, allowing it to cool down before potentially restarting.

Causes of damage to the Overload Compressor can include power surges, electrical faults within the refrigerator, or a malfunctioning compressor that requires more current than usual to operate. 

Symptoms of a bad Overload Compressor include:

• The refrigerator not cooling properly or not cooling at all
• The compressor failing to start, indicated by a clicking sound coming from the back of the refrigerator where the compressor is located.
• The refrigerator or freezer section warming up

This OEM LG part is also compatible with some Kenmore models.

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This fan guide directs airflow from the blower/fan assembly to improve cooling and airflow routing in the appliance. Replaces a cracked or missing guide to restore proper airflow and reduce noise from misdirected air. What it does:

• Channels air from the fan/blower to the correct vents or components
• Helps maintain even cooling and prevents hot spots near electronics or food compartments
• Reduces vibration-related rattles by securing the fan's airflow path
• Common symptom: airflow is weak, noisy, or misdirected when the guide is damaged or missing

• One fan guide

• High-level replacement — remove access panels and unplug appliance before starting
• Confirm correct orientation and secure mounting tabs/screws; avoid forcing plastic clips
• Use gloves to protect hands from sharp sheet metal edges inside the cabinet
• If airflow or noise persists after installation, inspect fan/blower and motor assembly for damage

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.

This drain tray assembly collects and directs moisture and condensate to the drain system, helping prevent leaks and pooling under the appliance. Designed to fit the appliance's drain path and restore proper drainage. What it does:

• Captures condensate and channel water toward the drain to reduce standing moisture.
• Helps prevent water from pooling under components that could cause corrosion or odors.
• Restores proper drain routing after a damaged or cracked tray is removed.
• Works with existing hoses and clips to maintain normal drainage performance.

• Disconnect power and water before beginning repair.
• Remove access panels or components as needed to reach the drain tray; keep fasteners organized.
• Inspect surrounding seals, hoses, and clips and replace any worn parts to ensure a watertight fit.
• Reassemble panels and test the appliance for proper drainage and leaks before returning to service.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This damper controls airflow between compartments to help maintain proper temperatures and consistent cooling. It replaces a worn or broken damper to restore normal airflow and temperature balance inside the appliance. What it does:

• Regulates air flow between compartments so the refrigerator can maintain set temperatures
• Helps reduce uneven cooling and temperature swings caused by a stuck or broken damper
• Works as part of the appliance's air distribution system to route cooled air where needed
• Common symptom: compartment temperature too warm or inconsistent airflow noise from the damper area

• One damper assembly

• High-level replacement; access usually requires removing interior panels or duct covers
• Disconnect power before any repair to avoid shock or injury
• Handle with care to avoid bending or damaging mounting tabs and linkage

The Defrost Control Assembly is an OEM part for LG refrigerators. It is designed to regulate the defrost cycle, ensuring that frost buildup on the evaporator coils is periodically melted away. This helps maintain efficient cooling performance and prevents excessive ice accumulation, which can hinder the refrigerator's functionality.

You should replace the defrost control assembly if it becomes faulty. Causes of a bad defrost control assembly can include electrical failures, regular wear and tear, or damage from power surges. A malfunctioning defrost control can lead to issues such as inadequate defrosting, which results in excessive frost buildup and affects the cooling efficiency of the refrigerator.

Symptoms of a bad defrost control assembly include:

• Frost buildup on the evaporator coils
• The refrigerator not cooling properly
• The defrost cycle not initiating or running too frequently
• Increased energy consumption due to the refrigerator working harder to maintain temperature

This OEM LG part is also compatible with Sears/Kenmore models.

The Refrigerator Control Assembly is an OEM part for LG refrigerators. This component is crucial for managing and regulating the refrigerator's cooling and defrosting cycles. It ensures the proper operation of the refrigerator by controlling the temperature and defrost settings.

Causes of a bad control assembly can include electrical surges, wear and tear over time, or moisture damage. These factors can lead to malfunctioning controls or inconsistent temperature regulation within the refrigerator.

Symptoms of a bad control assembly include:

• Refrigerator not cooling properly
• Unusual noises from the control panel
• Inconsistent temperature readings
• Refrigerator not defrosting automatically

This OEM LG part is also compatible with Sears/Kenmore.

Door switch magnet for reed switch

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

This DC motor drives the refrigerator's circulation fan, moving air across the coils and through the compartments for steady, efficient cooling. Replacing a weak, noisy, or seized motor restores airflow and temperature stability. What it does:

• Converts DC power into rotation to spin the attached fan and promote airflow
• Supports efficient heat exchange for even compartment temperatures
• Common symptoms: fan not running or intermittent, loud humming/squealing/grinding, warm spots or frost buildup, longer run times
• Contributes to reduced ice production or error codes in some models

• 1 DC motor

• Disconnect power and wear cut-resistant gloves; internal panels may have sharp edges
• Access the motor behind the interior panel or rear service panel; note connector orientation and wire routing
• Transfer the fan blade, grommets, and any mounting hardware from the old motor if needed
• Seat the blade fully and verify it spins freely before reassembly and restoring power

The Motor Assembly,dc is an OEM part for LG refrigerators. This fan motor assembly is responsible for circulating air within the fresh food compartment, ensuring proper cooling and temperature distribution. It provides the necessary airflow to keep your food items fresh and properly chilled.

Symptoms of a bad fan motor assembly include:

• Inadequate cooling in the fresh food compartment
• Unusual noises coming from the refrigerator
• Fan not spinning properly

A bad fan motor assembly can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as inadequate cooling in the fresh food compartment, unusual noises coming from the refrigerator, or the fan not spinning properly, it may be time to replace the fan motor assembly.

This LG replacement part is also compatible with Sears/Kenmore refrigerators.
 

The Evaporator Fan Motor is an OEM part for LG refrigerators. This motor circulates air within the refrigerator, ensuring even cooling and maintaining the desired temperature throughout the appliance.

Common causes of failure include wear and tear over time, electrical issues such as power surges, or physical damage from mishandling or impact.

Symptoms of a bad evaporator fan motor include:

• Unusual noises from the freezer or refrigerator compartments
• Inconsistent or insufficient cooling
• The motor not running or running sporadically
• Ice buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with some Kenmore models.

This lamp cover is the replacement clear/white lens that protects and diffuses the appliance interior light, restoring proper illumination and preventing direct bulb contact. It helps keep the light assembly enclosed and looking finished. What it does:

• Protects the interior light bulb from spills, dust, and impact
• Diffuses light for even illumination inside the appliance
• Restores a cracked, yellowed, or missing lens to improve visibility
• Prevents direct contact with the bulb for safer operation

• One lamp cover (lens) as shown

• Remove power to the appliance before replacing the lens (unplug or shut off circuit)
• Typically snaps or screws into the light housing; use care to avoid breaking the new lens
• Inspect the light housing and bulb; replace bulb if damaged before reassembly