Kenmore Washer 110.81361840 (11081361840, 110 81361840) Parts

The Washer Lid Screw is an OEM part for Whirlpool washing machines. This 6-32 x .340 screw secures the washer lid to the hinge assembly, ensuring the lid opens and closes smoothly and stays securely in place during operation.

Causes of a bad washer lid screw can include wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or mishandling. A compromised screw can lead to issues with the lid's stability and functionality.

Symptoms of a bad washer lid screw include:

• The washer lid feeling loose or wobbling
• Difficulty in opening or closing the lid
• Visible rust or corrosion on the screw
• The lid not staying securely in place

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Shoe is an OEM part for Whirlpool washing machines. This part stops the spinning tub during the spin cycle, allowing the washer to transition smoothly to the next phase of the cycle.

Causes of a bad brake shoe can include regular wear and tear, excessive friction from heavy loads, or breakage due to mishandling.  

Symptoms of a bad brake shoe include:

• The washing machine not stopping the spin cycle promptly
• Loud squeaking or grinding noises during or after the spin cycle
• The tub continuing to spin when the lid is opened
• The washer shaking or vibrating excessively during the spin cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

These lid bumpers are sold individually.

Used to lock washer cabinet to rear wall of washer.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

The straight-vane agitator is the finned center post that drives wash action in a top-load washer. It replaces a cracked or stripped agitator to restore proper clothes movement and consistent cleaning performance. What it does:

• Mounts on the drive shaft and oscillates to move laundry through wash water and detergent
• Restores wash action when vanes are broken or the internal splines are worn/stripped
• Helps address weak agitation, clothes not circulating, unusual rattling from a loose agitator, or visible damage
• Direct replacement for the original straight-vane agitator design

• 1 straight-vane agitator

• Disconnect power and turn off water before servicing
• Remove the center cap and hold-down bolt; lift the old agitator straight up
• Align splines, seat the new agitator, then reinstall the bolt and cap snugly
• Run a short cycle to ensure proper operation

The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.

Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.

Symptoms of a bad spacer include:

• Misalignment of components
• Unusual noises during operation
• Difficulty in assembling or disassembling parts
• Reduced efficiency of the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Sold individually, four are needed to replace all parts. Screw part number WP3390631.

This rear panel support is the structural bracket that secures the appliance's rear cover/backguard in place. Replacing a worn or broken support restores proper alignment, helps protect internal components, and reduces vibration noise.

• Secures the rear panel/backguard to the chassis for stable, proper fit
• Maintains alignment of panels and mounting points
• Helps minimize vibration, flexing, and rattles from a loose rear panel
• Common signs of failure: cracked or missing bracket, stripped mounting points, panel movement or buzzing

• Disconnect power at the breaker; shut off gas supply
• Pull the appliance forward carefully to access the back; protect flooring
• Remove fasteners, replace the damaged support, and reuse original hardware/clips
• Keep wiring clear of sharp edges; tighten screws evenly without over-torquing and check for vibration before repositioning

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

Rubber grommet for motor mount stud.

10 - 16 x 1/2

This thrust ring is a small spacer that controls end-play on a shaft or gear, keeping parts aligned and reducing friction. Replacing a worn ring restores smoother, quieter operation and helps prevent premature wear in the assembly.

• Maintains axial spacing and limits end-play in rotating assemblies
• Reduces friction and metal-to-metal contact between components
• Helps stabilize shafts/gears to minimize noise and vibration
• Replace if you notice scraping/grinding sounds, wobble, or visible wear on the old ring

• Disconnect power before servicing
• Refer to your model's parts diagram to confirm orientation and stack order with any spacers/washers
• Clean the shaft and mating surfaces; replace any companion parts that show severe wear
• After reassembly, check for smooth rotation and proper end-play before returning to service

This vacuum break is the washer's water-inlet anti-siphon fitting. It maintains a required air gap so the tub fills properly without drawing used water back into the supply, helping prevent leaks and backflow issues.

• Maintains an air gap at the inlet to prevent backflow/siphoning into household water lines
• Helps ensure consistent, unobstructed water flow into the tub
• Replaces a cracked, clogged, or leaking vacuum break at the fill area
• Common symptoms include leaks from the rear/top during fill, visible cracks, or restricted/noisy fill

• Unplug the appliance and shut off both water supplies before servicing
• Access the fill/inlet area; note hose routing and part orientation
• Remove hose clamps/hoses and the old vacuum break; install the new part and secure clamps
• Restore water and power, then run a fill test and check carefully for leaks

Specs: 10-16 x 1/2 inch.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.

• Delivers household power to the unit's main electrical connection
• Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
• Helps resolve issues like no power, tripping breakers, or visible cord damage

• Unplug the appliance and turn off the circuit breaker before starting
• Verify outlet type and cord routing match your original installation
• Transfer any cord clamp/retainer as needed and secure against sharp edges
• Inspect for proper grounding and test operation before returning to service