Kenmore Washer Dryer Combo 110.98764791 (11098764791, 110 98764791) Parts

The Thermal Cutoff is an OEM replacement part for Whirlpool dryers. This cutoff component plays a crucial role in starting and stopping power to the dryer during operation. It does so through a sensitive thermal limiter that responds to temperature changes inside the dryer drum. 

Causes of a bad cutoff can include damage or wear to the thermal limiter over time, loosening of internal wiring connections, or issues with the cutoff's electronic components. 

Symptoms of a bad thermal cutoff include: 

• The dryer not turning on at all 
• The dryer fails to turn off after a full cycle
• Fluctuations in heat output during drying
• Buzzing or clicking noises coming from the cutoff area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Broken Belt Switch Kit is an OEM replacement part for Whirlpool dryers. It is an assembly that includes a microswitch and bracket installed to monitor the dryer drum belt status. The broken belt switch plays an important safety role by automatically stopping the dryer if it detects the drum belt breaking or slipping off the motor pulley during a cycle. The kit includes a switch, actuator lever, screws, and wire terminals.

Causes of a bad broken belt switch can include wear and tear over time, electrical malfunctions, or physical damage from a broken belt or other internal issues. Ensuring the switch is functioning correctly is crucial for the safe and efficient operation of the dryer.

Symptoms of a broken or failing switch include: 

• The dryer failing to shut off if the belt breaks during operation
• Inability to diagnose belt issues through error code displays  
• Intermittent stopping or variance in belt tension detection

This genuine Whirlpool switch replacement is also compatible with Kenmore, Maytag, Jenn-Air, and KitchenAid dryer models.

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

This idler pulley assembly keeps the drive belt properly tensioned and aligned so your appliance runs smoothly and quietly. Replacing a worn or seized idler restores reliable belt drive and helps prevent slippage, noise, and no-drive issues.

• Maintains spring-loaded tension on the drive belt
• Spins freely to reduce friction and belt wear
• Helps route and align the belt between the motor and drum/basket
• Typical symptoms of a failing idler: squealing/chirping, belt fraying or coming off, intermittent or no tumble/spin, burning rubber smell

• Disconnect power; for gas units, also shut off the gas supply.
• Relieve belt tension, swap the assembly, and route the belt per your unit's diagram.
• Rotate the drum/basket by hand to check alignment.
• Wear cut-resistant gloves and use caution around sharp edges and spring tension.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

These lid bumpers are sold individually.

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This lint screen traps fibers and debris as air circulates through the dryer. A clean, intact screen helps maintain airflow, improve drying performance, and protect the blower and vent from excessive lint buildup.

• Captures lint and debris from laundry during drying
• Helps maintain proper airflow to reduce extended dry times
• Assists in preventing lint from entering the blower housing and vent
• Replace if mesh is torn, frame is warped, or screen no longer seats properly

• Unplug dryer before servicing
• Remove the old screen from the filter housing; clear any lint from the chute
• Insert the new screen fully so it seats flat and snug
• Clean the lint screen before or after each load to maintain performance

10 - 16 x 1/2

The door switch detects whether the dryer door is open or closed, enabling the motor and heater only when it's safe. Replacing a failed switch restores proper start/stop control and drum light behavior.

• Senses door position and completes or interrupts the dryer's run/heat circuits
• Shuts the dryer off when the door opens for safety
• Common symptoms: dryer won't start with the door closed; doesn't stop when door opens; drum light stays on or won't turn on
• Intermittent operation when the door is moved or pressed

• Disconnect power before servicing; allow components to cool
• Access the switch from the door opening or front panel; remove screws or release locking tabs
• Note wire positions and transfer them one at a time to the new switch
• Verify operation before reassembly: dryer should not run with the door open; drum light should respond

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

Specs: 10-16 x 1/2 inch.

This top front lock secures the front edge of a lift-up range cooktop to the cabinet frame. Replacing a worn lock restores a flush, stable fit so the cooktop stays closed during everyday cooking and cleaning.

• Locks the cooktop down to prevent unintended lifting during use or cleaning
• Maintains alignment so the front edge sits flush and stable
• Reduces vibration and rattling from a loose or misaligned top
• Common symptoms: cooktop won't latch or stay down, front gap, rattling or movement

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Lift the cooktop to access the front frame, remove the old lock, and install the new lock in the same orientation
• Secure with the original fasteners and verify the lock fully engages the mating catch
• Close the cooktop and confirm a flush, stable fit

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This tub ring mounts to the top of the washer's outer tub to act as a splash guard and cover. Replacing a cracked or loose ring helps contain wash water and helps prevent leaks or debris from the top. What it does:

• Forms the upper splash guard around the outer tub to keep water contained during wash and spin
• Serves as the top cover at the tub opening, locking in with tabs/clips
• Damage (cracks, broken tabs) may lead to leaks from the top, rattling, or a loose ring
• Visible wear can leave plastic fragments in the basket or around the tub opening

• 1 tub ring

• Disconnect power and turn off water supplies before servicing
• Lift or remove the top/console per model design to access the tub opening; support the lid
• Release the locking tabs/clips and remove the old ring; clean the tub lip
• Align and press the new ring evenly until all tabs fully engage; reassemble and test