Kenmore Dishwasher 363.14579000 (36314579000, 363 14579000) Parts

We ordered the item appliance parts pros said would fit our make/model. the part arrived in perfect condition faster than i could possibly imagine, and while it fit our machine, it was a big bigger than the original and it fits off-center, but i guess it works fine! excellent speed and ease of ordering. thanks Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

• Will not dispense detergent

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

• Won't start
• Door latch failure
• Door won't close

With the power to the dishwasher on, I removed the six or seven screws holding the door panel together. With the door separated, I manually moved the switch which should close when the dishwasher latch closes. This illuminated and activated the control panel telling me that the problem was in the door latch. I purchased a new latch from appliance parts pros and installed it. Very easy fix for a homeowner, taking thirty minutes. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

• Will not fill with water
• Will not drain

Put in the new parts and now it does not leak anymore. Very simple Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more

Replaced the upper and lower racks. AppliancePartsPro shipped the racks fast and they are a perfect fit. I think they're even a better, stronger design then the factory originals. Read more

Myself removed old part replaced with new Read more

In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside. Read more

Replaced heating element. Read more

• Leaking

I replaced the pump drain assembly. The flapper valve was included in the assembly, so I did not need to order that. On previous repairs, the old drain hose was tricky to reinstall, so I replaced it and the hose clamp.The silverware basket had holes in the bottom and required replacement. I had some broken tine clips. Read more

Repair parts arrived super fast. Installed the new parts according to the supplied instructions. All went well. It took over 2 hours because the unit had to be removed after the water and power were disconnected and then the initial problem diagnosed (motor brushes worn beyond service limits). The removal of the spray bar tower assembly was a challenge until it was discovered that the tower unscrews in a CW direction from the bar that then allowed access to the attachment screw that holds that... Read more