Kenmore Dishwasher 665.1743590 (6651743590, 665 1743590) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302868
Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.
Do-It-Yourself Stories from Customers like You
Dishwasher door panel was rusting Prashant K. • Fishers , IN • October 11, 2014
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193646
The Actuator is an OEM part for Whirlpool dishwashers. This actuator is responsible for releasing detergent from the dispenser at the appropriate time during the wash cycle, ensuring effective cleaning of the dishes.
Causes of a bad detergent dispenser actuator can include electrical malfunctions, wear and tear from frequent use, or physical damage to the actuator mechanism.
Symptoms of a bad detergent dispenser actuator include:
- The detergent not dispensing during the wash cycle
- The dispenser door not opening
- Dishes not being cleaned properly due to no detergent release
- Error codes related to the dispenser
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Latch would not open consistently on detergent dispenser James G. • Waxhaw , NC • January 12, 2015
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle.
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: 676458
Color: Gray. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For white order 675679. To attach these tine tips you will need to order the dishrack gray touch-up paintWP676455.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$27.25
- Compare At:
-
$32.43
- You Save:
-
$5.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10082894
This base heater assembly restores the oven's lower heating function in select convection microwaves. It delivers bottom radiant heat for baking and crisping so the unit can preheat properly and brown foods evenly.
- Supplies bottom heat during convection, bake, or crisp cycles
- Works with the control and temperature sensor to reach and maintain set temperature
- Common symptoms of a failed heater may include no heat in convection mode, very long preheat, or poor browning/crisping
- Visible damage to the element or tripping a circuit breaker may also indicate a shorted heater
What's included: 1 base heater assembly Install notes:
- Disconnect power before servicing. Microwaves contain high-voltage components that can retain a charge even when unplugged
- Allow the unit to cool completely; access typically requires removing the outer cover or lowering an over-the-range unit
- Note wire locations and routing before removal; transfer any brackets, shields, or screws from the original assembly
- Route wires exactly as original and avoid pinching; confirm clearances before reassembly and test a convection preheat
Do-It-Yourself Stories from Customers like You
Did not dry dishes David M. • Myrtle Beach , SC • November 11, 2016
Replaced the fuse resistor and the heating element.
Read more
More
$61.95
- Compare At:
-
$74.34
- You Save:
-
$12.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3373234
This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.
- Provides the pivot/anchor surface for the door spring at the cabinet frame
- Maintains balanced door opening and closing force
- Reduces friction, wear, and squeaks at the spring connection
What's included: Includes 1 bushing. Install notes:
- Disconnect power at the breaker and shut off water supply.
- Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
- Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
- Inspect both sides and replace worn components in pairs to keep door tension even.
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3368928
This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:
- Cuts power when overheating is detected to protect internal components
- Helps prevent damage from shorted heaters, motors, or wiring faults
- Common symptoms: no power, won't start, shuts off during operation, no lights/display
- A blown fuse reads open (no continuity) and must be replaced—it is not resettable
What's included:
Install notes:
- Disconnect power before servicing to avoid electrical shock
- Access the fuse location per your model's service information; note wire orientation and mounting
- Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.
Do-It-Yourself Stories from Customers like You
Heated dry wouldn't work Steven L. • Fenton , MI • June 13, 2014
I took a multimeter and found out that the old fuse was open. I ordered this new one and popped it in. Pretty easy fix and it's still going strong.
Read more
More
$54.61
- Compare At:
-
$57.76
- You Save:
-
$3.15
Genuine Whirlpool part
By: Whirlpool
Part Number: 675679
Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 4386996A
The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.
Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.
Symptoms of a faulty impeller include:
- Inadequate water circulation yielding poor cleaning
- Food particles or utensils not fully rinsed
- Loud clicking or grinding noises mid-cycle
- Error codes relating to low water pressure
Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.
Do-It-Yourself Stories from Customers like You
Water leak under the pump Tim V. • Affton , MO • June 02, 2014
Ordered the replacement pump seal kit from AppliancePartsPros. I watched the online how-to video on their website. The impeller was slightly stuck on the motor shaft due to age but overall was amazed at how easy it was to repair. Thanks AplianePartsPros!
Read more
More
$81.95
- Compare At:
-
$98.34
- You Save:
-
$16.39
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374343
This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.
- Counterbalances the door for smooth opening and closing
- Helps prevent the door from slamming open or feeling heavy
- Supports stable, mid-position hold when springs are intact and matched
- Common signs of failure: door drops quickly, is hard to lift, or won't stay in position
What's included: 1 door spring Installation notes:
- Disconnect power and water; remove the toe kick/access panel to reach the springs
- Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
- Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
- Wear gloves and eye protection; keep hands clear of moving hinges
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$21.95
- Compare At:
-
$26.34
- You Save:
-
$4.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3367052
This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.
- Applies clamping force around a hose to hold it on a barb or stub fitting
- Commonly used on washer drain and tub-to-pump hose connections
- Helps stop drips at the joint and prevents the hose from slipping off
- Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band
What's included: 1 hose clamp Installation notes:
- Unplug the appliance and turn off water supply; expect some residual water
- Seat the hose fully on the fitting; place the clamp just behind the bead/barb
- Tighten until snug and secure; do not overtighten to avoid damaging the hose
- Run a short test cycle and recheck for leaks at the connection
Do-It-Yourself Stories from Customers like You
Fill hose leaking at crimp fitting by faucet connector faucet adapter leaking (whirlpool portable dishwasher) Ralph P. • San Antonio , TX • August 21, 2016
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19